71.060.10 化学元素 标准查询与下载

ASTM D2798-11a(2019) 用于显微镜测定煤的玻璃体反射率的标准测试方法

Standard Test Method for Microscopical Determination of the Vitrinite Reflectance of Coal

ASTM D8093-19 核级石墨无损评价的标准指南

1.1 This guide provides general tutorial information regarding the application of conventional nondestructive evaluation technologies (NDE) to nuclear grade graphite. An introduction will be provided to the characteristics of graphite that defines the inspection technologies that can be applied and the limitations imposed by the microstructure. This guide does not provide specific techniques or acceptance criteria for end-user examinations but is intended to provide information that will assist in identifying and developing suitable approaches. 1.2 The values stated in SI units are to be regarded as the standard. 1.2.1 Exception—Alternative units provided in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Guide for Nondestructive Evaluation of Nuclear Grade Graphite

ASTM D5817-19 粒状和#x2014炭黑的标准实施规程；试验用总样品的还原、混合和干燥

Standard Practice for Carbon Black, Pelleted—Reduction, Blending, and Drying of Gross Samples for Testing

T/EERT 004-2019 工业副产品 硫磺

外观、硫（S）含量、水分、灰分、酸度（以H2SO4计）、有机物（以C计）

Industria by-product sulfur

ASTM D2414-19 炭黑的标准试验方法&x2014；吸油量（OAN）

Standard Test Method for Carbon Black—Oil Absorption Number (OAN)

ASTM D8255-19 小型核石墨试样断裂测量工作的标准指南

1.1 This guide provides general tutorial information and best practice for measuring the work of fracture on manufactured graphite and carbon specimens. Although applicable to all carbon and graphite materials, this guide is aimed specifically at measurements required on nuclear graphites, where there may be constraints on the geometry and/or volume of the test specimen. 1.2 The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not considered standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Guide for Work of Fracture Measurements on Small Nuclear Graphite Specimens

ASTM D6556-19 炭黑的标准试验方法&x2014；氮吸附的总表面积和外表面积

Standard Test Method for Carbon Black—Total and External Surface Area by Nitrogen Adsorption

ASTM D7854-18c 平均压力下炭黑空隙体积的标准试验方法

Standard Test Method for Carbon Black-Void Volume at Mean Pressure

ASTM D7854-18ce1 平均压力下炭黑空隙体积的标准试验方法

Standard Test Method for Carbon Black-Void Volume at Mean Pressure

ASTM D2414-18a 炭黑的标准试验方法&x2014；吸油量（OAN）

Standard Test Method for Carbon Black—Oil Absorption Number (OAN)

ASTM D8186-18 用电热蒸发电感耦合等离子体发射光谱法（ETV-ICP-OES）测量石墨中杂质的标准试验方法

1.1 This test method covers the measurement of mass fractions of the elements silver (Ag), aluminum (Al), arsenic (As), boron (B), barium (Ba), berylium (Be), bismuth (Bi), calcium (Ca), cadmium (Cd), cobalt (Co), chromium (Cr), copper (Cu), iron (Fe), potassium (K), lithium (Li), magnesium (Mg), manganese (Mn), molybdenum (Mo), sodium (Na), nickel (Ni), phosphorus (P), lead (Pb), sulfur (S), antimony (Sb), silicon (Si), tin (Sn), strontium (Sr), titanium (Ti), vanadium (V), tungsten (W), yitrium (Y), zinc (Zn), and zirconium (Zr) in graphite. 1.2 Provided that an appropriate validation procedure is carried out, this test method is also applicable to other carbon materials such as coal, coke, carbon black, graphite-felt, graphite-foil, graphite-foam, and fiber reinforced carboncarbon composites. 1.3 This test method is applicable to element contents from approximately 0.0001 mg ⁄kg to 1000 mg ⁄kg (0.1 ppmw to 1000 ppmw), depending on element, wavelength, measurement parameters, and sample mass. 1.4 The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not considered standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Measurement of Impurities in Graphite by Electrothermal Vaporization Inductively Coupled Plasma Optical Emission Spectrometry (ETV-ICP OES)

DIN 51918:2018 碳素材料试验.体积密度和开孔率的测定

The method is used for the determination of the bulk density and the open porosity by buoyancy method and the determination of the bulk density with of carbon and graphite materials (solid materials).

Testing of carbonaceous materials - Determination of bulk density and the open porosity

ASTM D2414-18 炭黑的标准试验方法&x2014；吸油量（OAN）

Standard Test Method for Carbon Black—Oil Absorption Number (OAN)

ASTM C1415-18 α光谱法测定²³⁸钚同位素丰度的标准试验方法

1.1 This test method covers the use of alpha spectrometry for determining the 238 Pu isotopic abundance in plutonium samples. It is particularly useful for samples in which the 238 Pu content is less than 1 % of the total plutonium content. For such samples, mass spectrometric results are vulnerable to bias because of potential interference from any 238 U isobar remaining after ion exchange. 1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for ²³⁸Pu Isotopic Abundance By Alpha Spectrometry

ASTM D7854-18b 平均压力下炭黑空隙体积的标准试验方法

Standard Test Method for Carbon Black-Void Volume at Mean Pressure

ASTM D7854-18a 平均压力下炭黑空隙体积的标准试验方法

1.1 This test method covers a procedure to measure a carbon black structure property by Void Volume at mean pressure. Compressed void volumes are obtained by measuring the compressed volume of a weighed sample in a cylindrical chamber as a function of pressure exerted by a movable piston. A profile of void volume as a function of pressure provides a means to assess carbon black structure at varying levels of density and aggregate reduction. For the purposes of standardized testing a single value of void volume is reported at 50 MPa mean pressure. 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Carbon Black-Void Volume at Mean Pressure

ASTM D7854-18 平均压力下炭黑空隙体积的标准试验方法

Standard Test Method for Carbon Black-Void Volume at Mean Pressure

ASTM D7633-13(2018) 炭黑碳含量的标准试验方法

1.1 This test method covers the instrumental determination of carbon content in a carbon black sample. Values obtained represent the total carbon content. 1.2 The method is applicable to tread, carcass and specialty type carbon blacks obtained from partial combustion or thermal decomposition processes, which typically contain 95 to 100 % carbon. 1.3 The results of these tests can be expressed as mass % carbon. 1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Carbon BlackCARBON CONTENT

KS M ISO 3425-2017(2022) 工业用硫.在850-900℃下灰分的测定

Sulphur for industrial use — Determination of ash at 850-900

KS M ISO 3705-2017(2022) 工业用硫.砷含量的测定.二乙基二硫代氨基甲酸银光度法

Sulphur for industrial use — Determination of arsenic content — Silver diethyldithiocarbamate photometric method