71.080.20 卤代烃 标准查询与下载

ASTM D3401-97(2022) 卤化有机溶剂及其混合物中水的标准试验方法

1.1 These test methods describe the use of the Karl Fischer (KF) titration for determination of water in halogenated organic solvents and mixtures thereof. Water concentrations from 2 ppm to 1000 ppm can be determined in these solvents. Two test methods are covered as follows: 1.1.1 Test Method A, Water Determination Using a Coulometric KF Titrator—The coulometric test method is known for its high degree of sensitivity (typically

Standard Test Methods for Water in Halogenated Organic Solvents and Their Admixtures

ASTM D2989-01(2022) 卤化有机溶剂及其混合物酸碱度的标准试验方法

1.1 This test method covers the determination of acidity in halogenated organic solvents and admixtures thereof. The alkalinity may be determined utilizing Test Methods D2106, by substituting the end point measured at pH 7 by bromothymol blue or pH meter. 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Specific precautionary statements are given in Section 7. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Acidity-Alkalinity of Halogenated Organic Solvents and Their Admixtures

ASTM D2109-01(2022) 卤化有机溶剂及其混合物中非挥发性物质的标准试验方法

1.1 These test methods cover the determination of nonvolatile matter in halogenated organic solvents and admixtures. 1.2 Five test methods are covered, as follows: 1.2.1 Test Method A—For halogenated organic solvents or admixtures having less than 50 ppm nonvolatile matter; or where precision better than 610 ppm is required. 1.2.2 Test Method B—For halogenated organic solvents or admixtures having more than 50 ppm nonvolatile matter or where precision of 60.001 % (10 ppm) is satisfactory. 1.2.3 Test Method C—For low-boiling halogenated organic solvents or their admixtures (for example, methylene chloride, trichlorotrifluoroethane) that may superheat and cause bumping while evaporating to dryness with steam. A precision of greater than 610 ppm can be attained. 1.2.4 Test Method D—For rapid measurement of nonvolatile matter in halogenated organic solvents and their admixtures and where precision better than 610 ppm is required. 1.2.5 Test Method E—For halogenated organic solvents or admixtures and where precision better than 610 ppm is required. 1.3 The values stated in SI units are to be regarded as standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Methods for Nonvolatile Matter in Halogenated Organic Solvents and Their Admixtures

ASTM D5616-04(2022) 回收三氯乙烯的标准规范

1.1 This specification covers the grades of trichloroethylene2 typically needed in various industries for noncritical applications such as in metal cleaning formulations. It may be used as a reference document by purchasers or persons establishing in-house trichloroethylene recovery programs. 1.2 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Reclaimed Trichloroethylene

ASTM D4079-00(2022) 蒸汽脱脂级二氯甲烷的标准规范

1.1 This specification covers vapor-degreasing grade methylene chloride. 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. NOTE 1—Guide D3844, Practice D4276, and MNL22 provide additional important information on vapor degreasing and solvent properties. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Vapor-Degreasing Grade Methylene Chloride

ASTM D2110-00(2022) 卤化有机溶剂及其外加剂水萃取物pH值的标准试验方法

1.1 This test method covers the measurement of the pH of water extractions of halogenated organic solvents and admixtures thereof. This test method is applicable for the determination of the pH of water extractions of virgin, reclaimed, or used solvents. 1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for pH of Water Extractions of Halogenated Organic Solvents and Their Admixtures

T/SDSCCE 012-2022 溴代正丁烷

本文件规定了溴代正丁烷的相关要求、试验方法、检验规则及标志、包装、运输、贮存等。 本文件适用于以氢溴酸和正丁醇为原料，在催化剂作用下经反应、精馏制得的溴代正丁烷。

1-Bromobutane

T/CCASC 6002-2021 氯碱工业绿色设计产品评价 氯化石蜡

前言　 1　范围　 2　规范性引用文件　 3　术语和定义　 4　评价原则　 5　评价要求　 6　评价方法　 附录A（规范性附录）检验方法和指标计算方法　

Evaluation of green designing for chlor alkali industry - Chlorinated paraffin

T/CPCIF 0135-2021 亚磷酸二乙酯副产氯乙烷

项    目　要    求 外观　12 ℃以下为无色透明液体，并无可见水 氯乙烷，w/%                                  ≥　95.0 乙醇，w/%                                    ≤　2.5 乙醚，w/%                                    ≤　2.4 水分，w/%                                    ≤　0.1 酸度（以HCl计），w/%                         ≤　0.002 蒸发残留物，w/%                              ≤　0.001

Chloroethane by product of diethyl phosphitel

T/ZZB 2338-2021 工业用八氟环丁烷

本文件规定了工业用八氟环丁烷的术语和定义、基本要求、技术要求、试验方法、检验规则、标志、包装、运输、贮存、安全和质量承诺。 本文件适用于由二氟一氯甲烷（HCFC-22）裂解生成四氟乙烯、再由四氟乙烯或四氟乙烯与八氟环丁烷共裂解、洗涤、压缩、精馏纯化制备的工业用八氟环丁烷。 化学名称：八氟环丁烷 分子式：C4F8 相对分子质量：200.03（按2018年国际相对原子质量）

Octafluorocyclobutane for industry use

T/ZZB 2337-2021 工业用二氟甲烷（HFC-32）

本文件规定了工业用二氟甲烷的基本要求、技术要求、试验方法、检验规则、标志、包装、运输和贮存、安全和质量承诺。 本文件适用于二氯甲烷和氟化氢为原料，用气相法或液相法，在催化剂作用下反应、精馏而得二氟甲烷。 分子式：CH2F2 结构式： 相对分子质量：52.024（按 2018 年国际相对原子质量）

Difluoromethane（HFC-32） for industrial use

T/SDEPI 017-2021 环氧氯丙烷副产 1,2,3-三氯丙烷

本文件规定了环氧氯丙烷副产1，2，3-三氯丙烷的原料及生产流程、要求、试验方法、检验规则、 标志、包装、运输和贮存。 本文件适用于以生产环氧氯丙烷过程中产生的副产物为原料，经过精馏提纯得到的1，2，3-三氯丙 烷，主要用作工业合成原料。其它通过精馏提纯含有1，2，3-三氯丙烷的废液生产的1，2，3-三氯丙烷 也可参照执行本文件。

By product 1,2,3-trichloropane from epichlorohydrin production

T/SDEPI 019-2021 环氧氯丙烷副产顺-1,3-二氯丙烯

本文件规定了环氧氯丙烷副产顺-1，3-二氯丙烯的原料及生产流程、要求、试验方法、检验规则、 标志、包装、运输和贮存。 本文件适用于以生产环氧氯丙烷过程中产生的副产物为原料，经过精馏提纯得到的顺-1，3-二氯丙 烯，主要用作工业合成原料。其它通过精馏提纯含有顺-1，3-二氯丙烯的废液生产的顺-1，3-二氯丙烯 也可参照执行本文件。

By product cis-1,3-dichloropropene from epichlorohydrin production

T/SDEPI 016-2021 环氧丙烷副产 1,2-二氯丙烷

本文件规定了环氧丙烷副产1，2-二氯丙烷的原料及生产流程、要求、试验方法、检验规则、标志、 包装、运输和贮存。 本文件适用于以生产环氧丙烷过程中产生的副产物为原料,经过精馏提纯得到的1，2-二氯丙烷，主 要用作工业合成原料。其它通过精馏提纯含有二氯丙烷废液生产的1，2-二氯丙烷也可参照执行本文件

By product 1,2-dichlopropane from propylene oxide production

T/SDEPI 021-2021 环氧氯丙烷副产 2,3-二氯丙烯

本文件规定了环氧氯丙烷环氧氯丙烷副产2，3-二氯丙烯的原料及生产流程、要求、试验方法、检 验规则、标志、包装、运输和贮存。 本文件适用于以环氧氯丙烷装置中回收的1，2，3-三氯丙烷为主要原料，经过合成反应制得的2， 3-二氯丙烯，主要用作工业合成原料。

By product 2,3-dichloropropene from epichlorohydrin production

T/SDEPI 015-2021 环氧氯丙烷副产二氯丙烷

本文件规定了环氧氯丙烷副产二氯丙烷的原料及生产流程、要求、试验方法、检验规则、标志、包装、运输和贮存。 本文件适用于以生产环氧氯丙烷过程中产生的副产物为原料，经过精馏提纯得到的二氯丙烷，主要 用作工业合成原料。其它通过精馏提纯含有二氯丙烷废液生产的二氯丙烷也可参照执行本文件。

By product dichloropropane from epichlorohydrin production

T/SDEPI 018-2021 环氧氯丙烷副产 3-氯丙烯

本文件规定了环氧氯丙烷副产3-氯丙烯的原料及生产流程、要求、试验方法、检验规则、标志、包 装、运输和贮存。 本文件适用于以生产环氧氯丙烷过程中产生的低沸物为原料，经过精馏提纯后得到的3-氯丙烯，主 要用作工业合成原料。其它通过精馏提纯含有3-氯丙烯的废液生产的3-氯丙烯也可参照执行本文件。

By product 3-chloropropene from epichlorohydrin production

T/SDEPI 020-2021 环氧氯丙烷副产反-1,3-二氯丙烯

本文件规定了环氧氯丙烷副产反-1，3-二氯丙烯的原料及生产流程、要求、试验方法、检验规则、 标志、包装、运输和贮存。 本文件适用于以生产环氧氯丙烷过程中产生的副产物为原料，经过精馏提纯工艺得到的反-1，3- 二氯丙烯，主要用作工业合成原料。其它通过精馏提纯含有反-1，3-二氯丙烯的废液生产的反-1，3- 二氯丙烯也可参照执行本文件。

By product trans-1,3-dichloropropene from epichlorohydrin production

T/CPCIF 0128-2021 工业用三甲基乙酰氯（特戊酰氯）

项        目　要        求 　I型　II型 三甲基乙酰氯（特戊酰氯），w/%  ≥           　99.30　99.00 特戊酸质量分数，w/%            ≤           　0.20　0.50 特戊酸酐质量分数，w/%          ≤           　0.20　0.50 三氯化磷质量分数，w/%          ≤      　0.30　供需双方协商商定

Trimethylacetyl chloride（Pivaloyl chlorid）for industrial use

ASTM D7326-21 HFC混合物B（CH2FCF3、CHF2CF3和CO2）的搬运、运输和储存的标准实施规程

1.1 This practice covers guidance and direction to suppliers, reclaimers, purchasers, and users in the handling, transportation, and storage of HFC Blend B. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Handling, Transportation, and Storage of HFC Blend B (CH2FCF3, CHF2CF3, and CO2)