71.080.40 有机酸 标准查询与下载

HG/T 5401-2018 工业甲基磺酸铜

Industrial Copper Methanesulfonate

ASTM D5562-95(2018) 在铵或三乙醇胺皂存在下测定游离脂肪酸/酸值的酸度的标准测试方法

1.1 This test method covers determination of the acidity as free fatty acids in the presence of ammonium or triethanolamine soaps, or both, existing in a sample of sulfonated or sulfated oil, or both, by calculation from the total alkalinity and free-and-alkali combined fatty acids. 1.2 The values stated in SI units are to be regarded as standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Determination of the Acidity as Free Fatty Acids/Acid Number in the Presence of Ammonium or Triethanolamine Soaps

ASTM D5560-95(2018) 用于测定脂肪和油中的中性脂肪物质的标准测试方法

1.1 This test method covers all degraded glycerides, since they are neutral fats. However, this procedure does not necessarily determine all the mono and diglycerides that may be present in the sample. This is due to the water soluble characteristics of some mono and diglycerides. 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Determination of Neutral Fatty Matter Contained in Fats and Oils

T/ZZB 0462-2018 2,4,5-三氟苯乙酸

本标准规定了2,4,5-三氟苯乙酸的基本要求、技术要求、试验方法、检验规则、标志、包装、运输和贮存、劳动防护、质量承诺。 本标准适用于以1,2,4-三氟苯为原料制备而得的2,4,5-三氟苯乙酸。该产品可作为合成糖尿病药物西他列汀的关键中间体。 分子式：C8H5F3O2。 相对分子质量：190.12（按2016年国际相对原子质量）。 结构式： 。

2,4,5-Trifluorophenyl acetic acid

ASTM D8207-18 原子吸收光谱法测定精对苯二甲酸（PAT）中金属含量的标准试验方法

1.1 This test method covers the determination of aluminum, chromium, cobalt, titanium, iron, manganese, molybdenum, sodium and nickel in purified terephthalic acid (PAT) by graphite furnace atomic absorption (GFAA) spectrometry. It is applicable to PAT samples containing sodium, chromium, cobalt, titanium, manganese, molybdenum and nickel over 0.004 mg/kg, and iron and aluminum over 0.054 mg/kg. 1.2 In determining the conformance of the test results using this method to applicable specification, results shall be rounded off in accordance with the rounding-off method of Practice E29. 1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Some specific hazards statements are given in 6.3, 6.10, 6.11, Section , and 9.1. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Determination of Metals in Purified Terephthalic Acid (PAT) by Atomic Absorption (AA) Spectrometry

ASTM D1240-14(2018) 松香化学品松香酸含量的标准试验方法 包括松香 妥尔油和相关产品

1.1 These test methods cover the determination of rosin acids in tall oil, tall oil fatty acid, tall oil rosin, and other pine chemicals products. 1.2 These test methods may not be applicable to adducts or derivatives of rosin, fatty acid, or other pine chemicals products. 1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Methods for Rosin Acids Content of Pine Chemicals, Including Rosin, Tall Oil, and Related Products

ASTM D5317-98(2017) 用电子捕获检测器通过气相色谱法测定水中氯化有机酸化合物的标准测试方法

1.1 This test method covers a gas chromatographic procedure for the quantitative determination of selected chlorinated acids and other acidic herbicides in water. Similar chemicals may also be determined by this test method, but it is the user’s responsibility to verify the applicability of this test method to any compounds not listed in this scope. The acid form of the following compounds were interlaboratory tested using this test method, and the results were found acceptable:2 Analyte Chemical Abstract Services Registry Number Bentazon 25057-89-0 2,4-D 94-75-7 2,4-DB 94-82-6 DCPA acid metabolites 2 Dicamba 1918-00-9 3,5-Dichlorobenzoic acid 51-36-5 Dichlorprop 120-36-5 5-Hydroxydicamba 7600-50-2 Pentachlorophenol (PCP) 87-86-5 Picloram 1918-02-1 2,4,5-T 93-76-5 2,4,5-TP (Silvex) 93-72-1 1.2 This test method may be applicable to the determination of salts and esters of analyte compounds. The form of each acid is not distinguished by this test method. Results are calculated and reported for each listed analyte as the total free acid. 1.3 This test method has been validated in an interlaboratory test for reagent water and finished tap water. The analyst should recognize that precision and bias reported in Section 18 may not be applicable to other waters. 1.4 This test method is restricted to use by or under the supervision of analysts experienced in the use of gas chromatography (GC) and in the interpretation of gas chromatograms. Each analyst must demonstrate the ability to generate acceptable results with this test method using the procedure described in 19.3. It is the user’s responsibility to ensure the validity of this test method for waters of untested matrices. 1.5 Analytes that are not separated chromatographically, that is, which have very similar retention times, cannot be individually identified and measured in the same calibration mixture or water sample unless an alternate technique for identification and quantitation exists (16.6, 16.7, and 16.8). 1.6 When this test method is used to analyze unfamiliar samples for any or all of the analytes given in 1.1, analyte identifications must be confirmed by at least one additional qualitative technique. 1.7 The values stated in SI units are to be regarded as standard. The values given in parentheses are mathematical conversions to inch-pound units that are provided for information only and are not considered standard. 1.8 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific warning statements, see Sections 6, 8, 9, and 10. 1.9 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Determination of Chlorinated Organic Acid Compounds in Water by Gas Chromatography with an Electron Capture Detector

ASTM D4416-09(2017) 丙烯酸标准规范

1.1 This specification covers glacial acrylic acid2 (99.0 % grade) for use in paint, varnish, lacquer and related products. 1.2 The following applies to all specified limits in this standard; for purposes of determining conformance with this standard, an observed value or a calculated value shall be rounded off “to the nearest unit” in the last right-hand digit used in expressing the specification limit, in accordance with the rounding-off method of Practice E29. 1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.4 For hazard information and guidance, see the supplier’s Safety Data Sheet. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific hazard statements, see Section 6. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Acrylic Acid

ASTM D3620-04(2017) 冰醋酸标准规范

1.1 This specification covers glacial (99.8 %) acetic acid for use in paint, varnish, lacquer, and related products. 1.2 The following applies to all specified limits in this standard; for purposes of determining conformance with this standard, an observed value or a calculated value shall be rounded off “to the nearest unit” in the last right-hand digit used in expressing the specification limit, in accordance with the rounding-off method of Practice E29. 1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 For specific hazard information and guidance, see the supplier’s Safety Data Sheet for materials listed in this specification. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Glacial Acetic Acid

HG/T 5279-2017 三氟乙酸（TFA）

Trifluoroacetic acid (TFA)

ASTM D5559-95(2017) 用于测定磺酸和硫酸化油中铵或三乙醇胺皂的游离脂肪酸/酸值的酸度的标准测试方法

1.1 This test method covers the determination of the acidity as free fatty acids existing in a sample of sulfonated or sulfated oil, or both, by titrating the sample dissolved in a solvent. It is not applicable in the presence of ammonium or triethanolamine soaps or salts or other compounds that do not react neutral to phenolphthalein when dissolved in alcohol. 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Determination of Acidity as Free Fatty Acids/Acid Number in the Absence of Ammonium or Triethanolamine Soaps in Sulfonated and Sulfated Oils

ASTM D4711-89(2017) 烷基苯磺酸中磺酸和硫酸的标准试验方法

1.1 This test method is applicable to the determination of sulfonic and sulfuric acids in branched and linear alkylbenzene sulfonic acids used as intermediates in synthetic detergents. 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Material Safety Data Sheets are available for reagents and materials. Review them for hazards prior to usage.

Standard Test Method for Sulfonic and Sulfuric Acids in Alkylbenzene Sulfonic Acids

ASTM D8130-17 采用感应耦合等离子体原子发射光谱法测定精对苯二甲酸(PTA)中金属含量的标准试验方法

4.1 The presence of metals in PTA used for the production of polyester is undesirable because they may speed up or slow down the reaction and be impurities in the final product. 4.2 Determination of the metals in PTA is often required. This test method is suitable for setting specifications and for use as an internal quality control where these products are produced or used. 4.3 This test method covers the determination of sodium, chromium, cobalt, aluminum, titanium, potassium, magnesium, manganese, iron, nickel, molybdenum and calcium. 1.1 This test method covers the determination of metal elements in purified terephthalic acid (PTA) by inductively coupled plasma atomic emission spectrometry (ICP-AES).This method is applicable to PTA samples containing sodium, chromium, cobalt, aluminum, titanium, potassium, magnesium, manganese, iron, nickel, molybdenum and calcium over 0.055 mg/kg, respectively. 1.2 In determining the conformance of the test results using this method to applicable specification, results shall be rounded off in accordance with the rounding-off method of Practice E29. 1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Determination of Metals in Purified Terephthalic Acid (PTA) by Inductively Coupled Plasma Atomic Emission Spectrometric Method

KS M 1655-2016(2021) 乙酸戊酯

Amyl acetate

KS M 1655-2016 醋酸戊酯

Amyl acetate

KS M 1661-2016 酒石酸

Tartaric acid

KS M 1662-2016 草酸

Oxalic acid

HG/T 5025-2016 工业甲基磺酸锡

Industrial tin methane sulfonate

SH/T 1499.4-2016 精己二酸 第4部分：灰分的测定

Adipic acid Part 4: Determination of ash content

HG/T 4792-2014 工业用DL-酒石酸

本标准规定了工业用DL-酒石酸的产品分类，要求，试验方法，检验规则以及标志、包装、运输和贮存等。 本标准适用于以顺丁烯二酸酐和过氧化氢为原料经氧化、水解制得的酒石酸。该产品主要用于生产酒石酸盐类产品，它在鞣革、照相、玻璃、搪瓷、电讯器材等工业也有非常重要的作用。 分子式：CHO ? nHO (结晶品n = 1，无水品n=0) 化学名称：2,3-二羟基丁二酸 相对分子质量：结晶品168. 11；无水品150. 09 (按2011年国际相对原子质量)

DL-tartaric acid for industrial use