71.080.60 醇、醚 标准查询与下载

T/CPCIF 0136-2021 工业用甲基丙烯酸羟乙酯、 2-甲基丙烯酸-1,2-丙二醇单酯 和2-丙烯酸-1,2-丙二醇单酯

表1　工业用甲基丙烯酸羟乙酯技术要求 项    目　要    求 　Ⅰ  型　Ⅱ  型　Ⅲ  型 甲基丙烯酸羟乙酯，w%                   ≥　99.0　97.0　93.0 色度/Hazen单位（铂-钴色号）              ≤　10　15　— 酸度（以甲基丙烯酸计），w%             ≤　0.1　0.1　0.2 水分，w%                               ≤　0.1　0.1　0.2 乙二醇二甲基丙烯酸酯，w%               ≤　0.2　0.5　— 阻聚剂/（mg/kg）　180～220　150～450　150～450 表2　工业用2-甲基丙烯酸-1,2-丙二醇单酯技术要求 项    目　要    求 　Ⅰ  型　Ⅱ  型　Ⅲ  型 2-甲基丙烯酸-1,2-丙二醇单酯，w%          ≥　98.0　96.0　93.0 色度/Hazen单位（铂-钴色号）              ≤　10　15　— 酸度（以甲基丙烯酸计），w%              ≤　0.1　0.1　0.2 水分，w%                                ≤　0.1　0.1　0.2 阻聚剂/（mg/kg）　150～450 表3　工业用2-丙烯酸-1,2-丙二醇单酯技术要求 项    目　要    求 　Ⅰ  型　Ⅱ  型　Ⅲ  型 2-丙烯酸-1,2-丙二醇单酯，w%              ≥　97.0　95.0　93.0 色度/Hazen单位（铂-钴色号）              ≤　10　15　— 酸度（以丙烯酸计），w%                  ≤　0.1　0.2　0.3 水分，w%                                ≤　0.1　0.1　0.2 阻聚剂/（mg/kg）　150～450

2-Hydroxyethyl methacrylate，Hydroxypropyl methacrylate（mixture of 2-hydroxypropyl and 2-hydroxy-1-methylethyl methacrylate）& Hydroxypropyl acrylate（mixture of 2-hydroxypropyl and 2-hydroxy-1-methylethyl acrylate）for industrial use

ASTM D7637-10(2021) 滴定法测定甘油含量的标准试验方法（偏高碘酸钠）

1.1 This test method provides the quantitative determination of glycerin by the titrimetric method. It is applicable to all glycerin or glycerin/water mixtures >75 %. 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 This standard may involve hazardous materials, operations, and equipment. This standard does not purport to address all of the safety concerns associated with its use. It is the responsibility of the user of this standard to consult the established and appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Specific precautions are listed in Section 8. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Determination of Glycerin Assay by Titration (Sodium Meta Periodate)

ASTM D7638-10(2021) 甘油中脂肪酸和酯测定的标准试验方法

1.1 This test method provides the quantitative determination of the fatty acid and ester content in purified glycerin by the titrimetric method. 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 This standard may involve hazardous materials, operations and equipment. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Specific precautions are listed in Section 8. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Determination of Fatty Acids and Esters in Glycerin

T/SDHCIA 009-2021 粗双三羟甲基丙烷

本文件规定了粗双三羟甲基丙烷的要求、试验方法、检验规则以及标志、包装、运输和贮存。 本文件适用于利用三羟甲基丙烷装置生产的粗双三羟甲基丙烷，用于生产工业用双三羟甲基丙烷及其他中间体合成。

Crude Ditrimethylolpropane

BS EN 15692:2021 乙醇作为汽油的调和成分 水分含量的测定 卡尔费休电位滴定法

Ethanol as a blending component for gasoline. Determination of water content. Karl Fischer potentiometric titration method

GSO ISO 17786:2021 燃料用二甲醚（DME） 高温（105℃）蒸发残渣的测定 质量分析法

ISO 17786:2015 specifies a procedure of test for high temperature (105 °C) evaporation residue in DME used as fuel by the mass analysis method. This procedure is applicable to determine the amount of high temperature (105 °C) evaporation residue up to the value specified in ISO 16861. Several tests can be applied to determine amount of evaporation residue in liquefied products. Among them, this International Standard specifies the method that has detection limit sufficient for a DME specification in ISO 16861, using less resource compared to other methods. When more precise quantitative test is required, use of ISO 13757 instead of this International Standard is recommended. Because of the procedure applied, the evaporation residue which has a boiling point lower than 105 °C will not be determined. NOTE The precision of this method has been studied for a limited set of samples and content levels by a limited amount of labs. It allows establishment of a quality specification of DME but cannot be considered as a full precision determination in line with the usual statistical methodology as in ISO 4259.

Dimethyl ether (DME) for fuels — Determination of high temperature (105°C) evaporation residues — Mass analysis method

T/CPCIF 0129-2021 工业用3-氯-2,2-二甲基丙酰氯（氯代特戊酰氯）

项        目　要        求 　I型　II型 3-氯-2,2-二甲基丙酰氯（氯代特戊酰氯）质量分数，w/%    ≥　99.00　98.50 二氯特戊酰氯质量分数，w/%                           ≤       　0.50　0.50 三甲基乙酰氯（特戊酰氯）质量分数，w/%               ≤            　0.30　0.50 氯代特戊酸酐质量分数，w/%                           ≤　0.20　0.50

3-Chloro-2,2-dimethyl propionyl chloride（Chloropivaloyl chloride）for industrial use

GSO ASTM D7666:2021 甘油三酯燃烧器燃料标准规范

This specification covers two grades of burner fuel consisting of triglycerides and naturally occurring constituents of triglycerides including monoglycerides, diglycerides, and free fatty acids and distinguished by the pour point. The triglyceride burner fuels, Grade TBF5 and Grade TBF6, are intended for use in commercial or industrial air or steam-atomized fuel oil burning equipment manufactured under various climatic and operating conditions for the purposes of heat generation. This specification describes the properties and limits for triglyceride burner fuels to provide acceptable performance in liquid fuel burning equipment. It also addresses significance and use, sample collection and handling, and properties that are those of greatest significance in obtaining acceptable performance of the burner. The requirements enumerated in this specification shall be determined in accordance with the following ASTM test methods except as noted: pour point (Test Method D97), flash point (Test Method D93, Procedure B, except when other methods may be prescribed by law), water and sediment (Test Method D1796), viscosity (Test Method D445), density (Test Methods D1298, D4052, D5355, or D7042), titer (Test Method D1982), acid number (Test Method D664), ash (Test Method D482), sulfur (Test Method D4294), insolubles (Grade TBF5 and Grade TBF6) (Test Method D128, Section 12, Method 1), and heating value (heat of combustion) (Test Method D240).

Standard Specification for Triglyceride Burner Fuel

ASTM D1133-13(2021) 烃溶剂中贝壳杉丁醇值的标准试验方法

1.1 This test method covers the determination of the relative solvent power of hydrocarbon solvents used in paint and lacquer formulations. This test method is suitable for use with solvents having an initial boiling point over 40 °C and a dry point under 300 °C when determined in accordance with the procedures in Note 1. NOTE 1—Test Method D86 is used to determine the initial boiling point and dry point for mineral spirits and similar petroleum solvents. Test Method D1078 is used for pure compounds and narrow boiling range cuts. 1.2 For purposes of determining conformance of an observed or a calculated value using this test method to relevant specifications, test result(s) shall be rounded off “to the nearest unit” in the last right-hand digit used in expressing the specification limit, in accordance with the rounding-off method of Practice E29. 1.3 For specific hazard information and guidance, consult the supplier’s Material Safety Data Sheet. 1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Kauri-Butanol Value of Hydrocarbon Solvents

SN/T 5298-2021 进口粗甘油检验规程

Inspection Regulations for Imported Crude Glycerol

T/CPCIF 0120-2021 工业用正戊醇

项    目　要    求 　合成级　溶剂级 外观　透明液体，无机械杂质 色度（铂-钴色号）/Hazen单位　≤15　≤15 正戊醇含量，w/%　≥99.0　60.0～65.0 2-甲基丁醇含量，w/%　≤0.2　35.0～40.0 水分，w/%　≤0.2　≤0.2 游离酸（以乙酸计），w/%　≤0.1　≤0.1

n-Amyl alcohol for industrial use

T/CPCIF 0123-2021 工业用3-甲基-3-丁烯-1-醇（异戊烯醇）

项    目　要    求 　Ⅰ  型　Ⅱ  型 3-甲基-3-丁烯-1-醇（异戊烯醇），w/%            ≥　99.50　99.00 水分，w/%                                    ≤　0.030　0.10 色度（铂-钴色号）/Hazen单位                   ≤　20　50 酸值（以氢氧化钾计）/（mgKOH/g）               ≤　3.0　6.0 过氧化值（以活性氧含量计），w/%              ≤　0.050　0.050

3-Methyl-3-buten-1-ol（Isoprenol）for industrial use

ASTM D7577-12(2021) 用于测定变性燃料乙醇和乙醇燃料混合物的加速铁腐蚀等级的标准测试方法

1.1 This test method measures the ability of inhibited and uninhibited Ethanol Fuel Blends defined by Specification D5798 and Denatured Fuel Ethanol defined by Specification D4806 to resist corrosion of iron should water become mixed with the fuel, using an accelerated laboratory test method. Corrosion ratings are reported based on a visual, numbered rating scale. 1.2 The values stated in SI units are to be regarded as standard. The values in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Specific hazard statements are given in Sections 7 and 8. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Determining the Accelerated Iron Corrosion Rating of Denatured Fuel Ethanol and Ethanol Fuel Blends

ASTM D7794-21 与汽车火花点火发动机混合的柔性燃料车辆用中级乙醇燃料共混物的标准实施规程

1.1?This practice applies to the blending of automotive spark-ignition engine fuels with ethanol concentrations greater than those suitable for conventional-fuel vehicles and less than the minimum ethanol content specification limits of Specification D5798. These mid-level ethan

Standard Practice for Blending Mid-Level Ethanol Fuel Blends for Flexible-Fuel Vehicles with Automotive Spark-Ignition Engines

prEN 15491-2021 作为汽油调合组分的乙醇 总酸度的测定 颜色指示剂滴定法

Ethanol as a blending component for petrol - Determination of total acidity - Colour indicator titration method

HG/T 2543-2021 工业用氯甲基甲醚

Industrial chloromethyl ether

HG/T 5801-2021 工业用十二碳醇酯

Industrial dodecyl alcohol ester

HG/T 5799-2021 一缩二丙二醇

Dipropylene glycol

T/CPCIF 0077-2020 工业用丙烯酸羟乙酯

项目　指标 　Ⅰ型　Ⅱ型　Ⅲ型 色度/ Hazen单位（铂-钴色号）           ≤　10　30　50 酸度（以丙烯酸计），w%                ≤　0.1　0.2　0.3 水分，w%                            ≤　0.1　0.2　0.3 丙烯酸羟乙酯含量，w%                ≥　97.0　93.0　90.0 乙二醇二丙烯酸酯a，w%                ≤　0.5　0.8　- 阻聚剂（对羟基苯甲醚）b，mg/kg                    　  150~450 注：Ⅰ型主要应用于高端涂料及油墨用树脂等领域，Ⅱ型主要应用于树脂、胶粘剂等领域，Ⅲ型主要应用于减水剂等其它领域。 a  当有特殊要求时，由供需双方协商解决。 b  当有特殊要求时，由供需双方协商解决。

2-Hydroxyethyl acrylate for industrial use

HG/T 4122-2020 工业用三羟甲基丙烷

Industrial trimethylolpropane