75.180.30 容积设备和容积测量 标准查询与下载
共找到 529 条与 容积设备和容积测量 相关的标准，共 36 页
ISO 6578:2017 specifies the calculation procedure to convert the volume of liquefied petroleum gas (LPG) and liquefied natural gas (LNG) under the conditions at the time of measurement to the equivalent volume of liquid or vapour at the standard condition, i.e. 15 °C and 101,325 kPaA, or to the equivalent mass or energy (calorific content). It applies to the quantities of refrigerated hydrocarbon liquids stored in or transferred to/from tanks and measured under static storage conditions. Calculation of pressurized gases is out of the scope of ISO 6578:2017.
Refrigerated hydrocarbon liquids — Static measurement — Calculation procedure
- ICS
- 75.180.30
- CCS
- 发布
- 2021-07-01
- 实施
ISO 2715:2017 describes and discusses the characteristics of turbine flowmeters. Attention is given to the factors to be considered in the application of turbine meters to liquid metering. These include the properties and nature of the liquid to be metered, the correct installation and operation of the meter, environmental effects, and the wide choice of secondary and ancillary equipment. Aspects of meter proving and maintenance are also discussed. ISO 2715:2017 is applicable to the metering of any appropriate liquid. Guidance is given on the use of turbine meters in the metering of two-component liquid mixtures such as water and oil. It is not applicable to two-phase flow when gases or solids are present under metering conditions (i.e. two-phase flow). It can be applied to the many and varied liquids encountered in industry for liquid metering and is not restricted to hydrocarbons. Guidance on the performance expected for fiscal/custody transfer applications for hydrocarbons is outlined. ISO 2715:2017 is not applicable to cryogenic liquids, such as liquefied natural gas (LNG) and refrigerated petroleum gas. It does not cover potable water applications.
Liquid hydrocarbons — Volumetric measurement by turbine flowmeter
- ICS
- 75.180.30
- CCS
- 发布
- 2021-07-01
- 实施
ISO 12917-1:2017 specifies manual methods for the calibration of nominally horizontal cylindrical tanks, installed at fixed locations. The methods in this document are applicable to insulated and non-insulated tanks, either when they are above-ground or underground. The methods are applicable to pressurized tanks and to both knuckle-dish-end and flat-end cylindrical tanks as well as elliptical and spherical head tanks. ISO 12917-1:2017 is applicable to tanks inclined from the horizontal, provided a correction is applied for the measured tilt. Although this document does not impose any limits on the maximum tank diameter and maximum tank tilt to which this document is applicable, the practical limits would be about 4 m in diameter and 10° in tilt.
Petroleum and liquid petroleum products — Calibration of horizontal cylindrical tanks — Part 1: Manual methods
- ICS
- 75.180.30
- CCS
- 发布
- 2021-07-01
- 实施
ISO 91:2017 refers to temperature volume correction factors, which allow users to convert volumes, measured at ambient conditions, to those at reference conditions for transactional purposes. This document also refers to compressibility factors required to correct hydrocarbon volumes measured under pressure to the corresponding volumes at the equilibrium pressure for the measured temperature.
Petroleum and related products — Temperature and pressure volume correction factors (petroleum measurement tables) and standard reference conditions
- ICS
- 75.180.30
- CCS
- 发布
- 2021-07-01
- 实施
ISO 2714:2017 describes and discusses the characteristics of displacement flowmeters. Attention is given to the factors to be considered in the application of positive displacement meters to liquid metering. These include the properties and nature of the liquid to be metered, the correct installation and operation of the meter, environmental effects, and the wide choice of secondary and ancillary equipment. Aspects of meter proving and maintenance are also discussed. ISO 2714:2017 is applicable to the metering of any appropriate liquid. Guidance is given on the use of positive displacement meters in the metering of two-component mixtures of the same phase such as water and oil. It is not applicable to two-phase flow when gases or solids are present under metering conditions (i.e. two-phase flow). It can be applied to the many and varied liquids encountered in industry for liquid metering only. It is not restricted to hydrocarbons. Guidance on the performance expected for fiscal/custody transfer applications for hydrocarbons is outlined. ISO 2714:2017 is not applicable to cryogenic liquids such as liquefied natural gas (LNG) and refrigerated petroleum gas. It does not cover potable water and fuel dispenser applications.
Liquid hydrocarbons — Volumetric measurement by displacement meter
- ICS
- 75.180.30
- CCS
- 发布
- 2021-07-01
- 实施
Petroleum measurement systems - Calibration - Volumetric measures, proving tanks and field measures (including formulae for properties of liquids and materials) - Amendment 1: Correction of two typographical errors (ISO 8222:2020/DAmd 1:2021)
- ICS
- 75.180.30
- CCS
- 发布
- 2021-07-00
- 实施
本文件是在我国燃油加油机（以下简称加油机）现行制造能力水平的基础上，结合技术发展和计量器具管理需求，参考国际法制计量组织技术文件、国家及行业相关标准制定。本文件充分考虑了《实施强制管理的计量器具目录》对加油机法制监管的要求和加油机行业自身发展与社会治理智能化监管相结合的需求。 本文件旨在对适应新时期技术发展和计量器具全生命周期市场监管的需求，为加油机设计、制造和验收提供相关指导，对加油机相关功能性能、试验方法和检验规则做出规定，为加油机生产制造质量保障、技术提升和管理提供了标准和指导。本文件的重点由五部分构成。 ——第1部分：通用要求。目的在于对加油机的通用结构和功能、法制管理要求、危险应急结构和功能、防爆性能做出要求。 ——第2部分：整机要求。目的在于对加油机整机的结构和外观、计量性能、油气回收性能、安全性能、环境适应性等做出要求。 ——第3部分：部件要求。目的在于对加油机核心计量部件、主要液压部件、油气回收功能主要部件做出要求。 ——第4部分：试验方法。目的在于对加油机整机和主要部件功能性能的试验方法做出规定。 ——第5部分：检验规则。目的在于对加油机整机和部件的型式评价和出厂检验试验项目和判定规则做出规定。 本文件能够促进我国加油机制造水平的提升，适应新时期计量器具管理的需求，为保障加油机的安全性与计量的准确性提供了标准和指导，有利于营造加油机行业诚信公平竞争环境，为计量数据发挥作用提供了必要的基础条件。其实施会促加油机制造的规范化、标准化、数字化、智能化发展。
Fuel dispensers
- ICS
- 75.180.30
- CCS
- C359
- 发布
- 2021-04-30
- 实施
- 2021-04-30
Bunkering of marine fuel using the Coriolis mass flow meter (MFM) system
- ICS
- 75.180.30
- CCS
- 发布
- 2021-01-18
- 实施
- 2021-01-18
This document specifies procedures and requirements for the transfer of bunkers to vessels by bunker tankers using the Coriolis mass flow meter (MFM) system. It encompasses the process leading to the approval of the MFM system as installed on bunker tankers and post-approval bunkering operation. It covers terminology, specifications, requirements and procedures on metrology, system integrity, metering system selection and installation, MFM system verification, bunker delivery and dispute handling. NOTE Local and international regulations, such as the International Convention for the Prevention of Pollution from Ships (MARPOL) can apply.
Bunkering of marine fuel using the Coriolis mass flow meter (MFM) system
- ICS
- 75.180.30
- CCS
- 发布
- 2021-01-00
- 实施
Petroleum and liquid petroleum products - Determination of volume, density and mass of the hydrocarbon content of vertical cylindrical tanks by hybrid tank measurement systems
- ICS
- 75.180.30
- CCS
- 发布
- 20201223
- 实施
- 20201223
Refrigerated light hydrocarbon fluids－General requirements for automatic level gauges－Part 2：Gauges in refrigerated-type shore tanks
- ICS
- 75.180.30
- CCS
- 发布
- 20201223
- 实施
- 20201223
Measurement of multiphase fluid flow
- ICS
- 75.180.30
- CCS
- 发布
- 2020-12-09
- 实施
- 2020-12-09
Measurement of multiphase fluid flow
- ICS
- 75.180.30
- CCS
- N12
- 发布
- 2020-11-00
- 实施
Guide to Selection of Flowmeters for Natural Gas Trade Measurement
- ICS
- 75.180.30
- CCS
- E98
- 发布
- 2020-10-23
- 实施
- 2021-02-01
Standard Test Method for Determination of Dynamic Viscosity and Derived Kinematic Viscosity of Liquids by Constant Pressure Viscometer
- ICS
- 75.180.30
- CCS
- 发布
- 2020-09-01
- 实施
Standard Test Method for Determination of Dynamic Viscosity and Derived Kinematic Viscosity of Liquids by Constant Pressure Viscometer
- ICS
- 75.180.30
- CCS
- 发布
- 2020-06-01
- 实施
This document describes the design, use and calibration of volumetric measures (capacity measures) which are intended for use in fixed locations in a laboratory or in the field. This document gives guidance on both standard and non-standard measures. It also covers portable and mobile measures. This document is applicable to the petroleum industry; however, it may be applied more widely to other applications. This document excludes measures for cryogenic liquids and pressurized measures as used for liquid petroleum gas (LPG) and liquefied natural gas (LNG). Volumetric measures are classified as test measures or prover tanks depending on capacity and design. Measures described in this document are primarily designed, calibrated and used to measure volumes from a measure which is wetted and drained for a specified time before use and designated to deliver. Many of the provisions, however, apply equally to measures which are used to measure a volume using a clean and dry measure and designated to contain. Guidance is given regarding commonly expected uncertainties and calibration specifications. The document also provides, in Annex A, reference formulae describing the properties of water and other fluids and materials used in volumetric measurement more generally.
Petroleum measurement systems - Calibration - Volumetric measures, proving tanks and field measures (including formulae for properties of liquids and materials) (ISO 8222:2020)
- ICS
- 75.180.30
- CCS
- 发布
- 2020-04-15
- 实施
- 2020-07-31
This document describes the design, use and calibration of volumetric measures (capacity measures) which are intended for use in fixed locations in a laboratory or in the field. This document gives guidance on both standard and non-standard measures. It also covers portable and mobile measures. This document is applicable to the petroleum industry; however, it may be applied more widely to other applications. This document excludes measures for cryogenic liquids and pressurized measures as used for liquid petroleum gas (LPG) and liquefied natural gas (LNG). Volumetric measures are classified as test measures or prover tanks depending on capacity and design. Measures described in this document are primarily designed, calibrated and used to measure volumes from a measure which is wetted and drained for a specified time before use and designated to deliver. Many of the provisions, however, apply equally to measures which are used to measure a volume using a clean and dry measure and designated to contain. Guidance is given regarding commonly expected uncertainties and calibration specifications. The document also provides, in Annex A, reference formulae describing the properties of water and other fluids and materials used in volumetric measurement more generally.
Petroleum measurement systems — Calibration — Volumetric measures, proving tanks and field measures (including formulae for properties of liquids and materials)
- ICS
- 75.180.30
- CCS
- 发布
- 2020-03-31
- 实施
What is ISO 21903 about? ISO 21903 is an international standard on refrigerated hydrocarbon fluids that discusses about its various functionalities. ISO 21903 specifies the metrological and technical requirements for flowmeters intended to be used for the dynamic measurement of liquefied natural gas (LNG) and other refrigerated hydrocarbon fluids. For LNG static volume measurement used in custody transfer, see ISO 10976 . ISO 21903 sets the best practice for the proper selection and installation of flowmeters in cryogenic applications and identifies the specific issues that can affect the performance of the flowmeter in use. Moreover, it offers a calibration guideline for laboratory and on-site conditions (mass or volume) by either using LNG or other reference fluids. The choice of calibration fluid will ...
Refrigerated hydrocarbon fluids. Dynamic measurement. Requirements and guidelines for the calibration and installation of flowmeters used for liquefied natural gas (LNG) and other refrigerated hydrocarbon fluids
- ICS
- 75.180.30
- CCS
- 发布
- 2020-02-29
- 实施
- 2020-02-29
This document specifies procedures and requirements for the transfer of bunkers to vessels involving bunker tankers, road tankers and shore pipelines. It is applicable to pre-delivery, delivery and post- delivery checks and documentation.
Petroleum products — Procedures for the transfer of bunkers to vessels
- ICS
- 75.180.30
- CCS
- 发布
- 2020-02-13
- 实施
