77.150.60 铅、锌和锡产品 标准查询与下载

JIS H 4301:1993 铅和铅合金薄板和板

この規格は,圧延した一般工業用に使用する鉛板，薄鉛板，テルル鉛板及び硬鉛板(以下，板という。)について規定する。

Lead and lead alloy sheets and plates

GOST 1180-1991 锌阳极.规范

Настоящий стандарт распространяется на горячекатаные аноды, применяемые для оцинкования деталей гальваническим способом

Zinc anodes. Specifications

JIS H 5301:1990 锌合金压铸件

この規格は，亜鉛合金ダイカスト(以下,ダイカストという。)について規定する。

Zinc alloys die castings

JIS H 5601:1990 硬铅铸件

この規格は，主に化学工業に用いる硬鉛鋳物(以下,鋳物という。)について規定する。

Hard lead castings

GOST 598-1990 多用途锌板.规范

Настоящий стандарт распространяется на холоднокатаные цинковые листы общего назначения, применяемые в различных отраслях промышленност

General-purpose zinc sheets. Specifications

SAE J469-1989 锌压铸合金

Because of the drastic chilling involved in die casting and the fact that the solid solubilities of both aluminum and copper in zinc change with temperature, these alloys are subject to some aging changes, one of which is a dimensional change. Both of the alloys undergo a slight shrinkage after casting, which at room temperature is about two-thirds complete in five weeks. It is possible to accelerate this shrinkage by a stabilizing anneal, after which no further changes occur. The recommended stabilizing anneal is 3 to 6 h at 100 �C (212 �F), or 5 to 10 h at 85 �C (185 �F), or 10 to 20 h at 70 �C (158 �F). The time in each case is measured from the time at which the castings reach the annealing temperature. The parts may be air cooled after annealing. Such a treatment will cause a shrinkage (0.0004 in per in) of about two-thirds of the total, and the remaining shrinkage will occur at room temperature during the subsequent few weeks. Stabilizing results in a decrease in dimensions of about 0.0005 in per in from the original size of the casting. Stabilizing is, of course, unnecessary if the machine or fitting operations can be delayed until the castings have aged five weeks at room temperature. When exposed to stagnant moisture or condensation with limited access to oxygen, a nonuniform type of corrosion may occur on zinc die castings, which often results in the formation of a bulky film of white corrosion products. This may hinder the operation of such parts as automobile lock cylinders, fuel pumps, and carburetors, and in severe cases result in rather rapid loss of zinc. Various types of chromate films are available to satisfactorily overcome this condition. The same electroplating or enameling procedure is used with both alloys. Organic finishes are quite variable in their ability to adhere well to zinc surfaces. The phosphate type of chemical pretreatment has received widest commercial utilization, and most zinc die castings which are to be finished with lacquers or enamels are phosphate pretreated. In general, a much wider selection of finishes can be used on pretreated die castings. The relative merits of the two SAE alloys may be outlined as follows.

Zinc Die Casting Alloys

GOST 9559-1989 铅片.规范

Настоящий стандарт распространяется на свинцовые листы, применяемые в химическом машиностроении и других отраслях промышленности

Lead sheets. Specifications

SAE J468-1988 锌合金锭和模的铸造成分

Zinc Alloy Ingot and Die Casting Compositions

Zinc Alloy Ingot and Die Casting Compositions

BS 3332:1987 轴承用巴比合金锭规范

Chemical composition of eight alloys in ingot form, with general requirements concerning inspection and testing.

Specification for white metal bearing alloy ingots

GOST 18326-1987 一级和多级浸蚀用低合金锌板.规范

Настоящий стандарт распространяется на листы из низколегированных сплавов цинка, применяемые для изготовления форм высокой печати однос

Low-alloyed zinc sheets for one-stage and multistage etching. Specifications

DD 139-1986 锌铝合金锭和铸件规范

Three alloys containing approximately 8%, 11% and 27% aluminium respectively.

Specification for zinc-aluminium alloy ingots and castings

BS DD 139:1986 锌铝合金铸锭和铸件规范

This Draft for Development specifies requirements for the chemical composition and identification of ingots and castings in three zinc-aluminium alloys, designated ZA8,ZA12 and ZA27. Methods for verifying that ingots and castings meet the requirements of this Draft for Development are also specified, together with methods for the selection and preparation of the samples.

Specification for zinc-aluminium alloy ingots and castings

AS 1881:1986 锌合金.铸锭和铸件.质量要求

Specifies quality requirements and conditions of supply for zinc alloys in ingot form for pressure diecasting and gravity casting and for castings made from them.

Zinc alloys - Casting ingots and castings - Quality requirements

NF A56-101:1985 减摩合金锭.特性

Antifriction alloy ingots. Characteristics.

CNS 4006-1985 铅板

本标准适用于以铅为材料所制之板制品。

Lead Plates

CNS 7-1984 铅锭

本标准适用于金属铅锭。

Lead Ingot

CNS 11112-1984 铅锭分析法

本标准规定 CNS 7 铅锭中化学成分（银、铜、铋、锑、砷、锡、铁、锌）之分析方法。

Methods of Chemical Analysis for Lead Ingot

CNS 9879-1983 锡锭

本标准适用于金属锡锭。

Tin Ingot

CNS 8504-1982 锌喷敷作业方法

本标准规定为防止铜铁产口锈蚀，在其表面采用瓦斯熔锌线喷敷作业。

Recommended Practice for Zinc Spray Coatings on Iron and Steel

ISO 301:1981 铸造用锌合金锭

The ingots shall have a mass of 5 to 20 kg, shall be of a shape which permits stacking, may include notches which allow them to be broken up if necessary into small pieces and may include cast-on feet. The marking is specified. Designations and chemical compositions of ingots are given in a table.

Zinc alloy ingots intended for casting