83.140.01 橡胶和塑料制品综合 标准查询与下载

T/SHBX 008-2021 全生物降解塑料饮用吸管

本文件规定了全生物降解塑料饮用吸管（以下简称吸管）的术语和定义、分类、技术要求、试验方法、检验规则、包装、包装标志、运输和贮存。

Bio-degradable drinking straws

T/ZS 0192-2021 室外塑胶跑道施工质量检查技术规程

  前 言   1 范围   2 规范性引用文件   3 术语和定义   4 基本要求   5 施工     5.1 一般要求     5.2 跑道基层施工     5.3 跑道面层施工   6 验收     6.1 一般要求     6.2 跑道基层验收     6.3 跑道面层验收     6.4 抽样及判定     6.5 检测方法...

Technical specification for construction quality inspection of outdoor plastic runway

T/GMALDDC 01-2021 土工合成材料 高密度聚乙烯土工膜

1.范围：规定了高密度聚乙烯土工膜的术语和定义、基础树脂的要求、产品分类、代号与命名、技术要求、试验方法、检验规则、包装、贮存和标志。 2.规范性引用文件：根据产品实际应用的内在质量考核项目要求，确定相关的检测方法标准。 3.术语和定义：根据产品构成和分类，明确高密度聚乙烯土工膜、光面土工膜、糙面土工膜的定义。 4.基础树脂的要求：根据高密度聚乙烯土工膜所用的原材料情况，确定树脂密度的要求，和回料、填充料的使用要求。 5.产品分类、代号和命名 5.1 产品分类和代号：引用GB/T 17643-2011《土工合成材料  聚乙烯土工膜》标准的5.1条款，产品按外观结构分为光面高密度聚乙烯土工膜和糙面高密度聚乙烯土工膜，糙面高密度聚乙烯土工膜根据糙面分布情况又分单糙面和双糙面。光面高密度聚乙烯土工膜的代号为GH-2S，单糙面高密度聚乙烯土工膜的代号为GH-2T1，双烽面高密度聚乙烯土工膜的代号为GH-2T2。 5.2产品命名：引用GB/T 17643-2011《土工合成材料  聚乙烯土工膜》标准5.2条款，以产品代号+产品宽度+产品厚度+团体标准代号命名产品规格。 6.要求：引用GB/T 17643-2011《土工合成材料 聚乙烯土工膜》标准的第6条款，分为规格尺寸及偏差、外观质量、技术性能指标。 6.1  规格尺寸：根据市场应用情况，高密度聚乙烯土工膜的厚度为0.75mm、1.0mm、1.25mm、1.5mm、2.0mm、2.50mm、3.00mm；宽度不应小于2000mm，单卷长度不应小于30m。厚度偏差、宽度偏差、长度偏差的要求引用GB/T 17643-2011《土工合成材料 聚乙烯土工膜》标准中的6.1条款。 6.2 外观质量：引用GB/T 17643-2011《土工合成材料 聚乙烯土工膜》标准的第6.2条款。 6.3 技术性能指标:引用GB/T 17643-2011《土工合成材料 聚乙烯土工膜》标准，确定需要考核的项目为：密度、拉伸屈服强度、拉伸断裂强度、屈服伸长率、断裂伸长率、直角撕裂负荷、抗穿刺强度、拉伸负荷应力开裂、碳黑含量、碳黑分散性、氧化诱导时间（OIT）、85℃烘箱老化（90天后标准OIT保留率）、抗紫外线（紫外线照射1600h后OIT保留率)。 7.检验规则 引用GB/T 17643-2011《土工合成材料 聚乙烯土工膜》标准。 8.标志、包装、贮运和运输    引用GB/T 17643-2011《土工合成材料 聚乙烯土工膜》标准。

Geosynthetics high density Polyethylene geomembrane

DIN EN ISO 13000-2:2021 塑料. 聚四氟乙烯(PTFE)半成品. 第2部分: 试样的制备和特性的测定(ISO 13000-2-2021); 德文版本EN ISO 13000-2-2021

This document specifies the preparation of test specimens and gives the test methods applicable to semi-finished products of polytetrafluoroethylene (PTFE).

Plastics - Polytetrafluoroethylene (PTFE) semi-finished products - Part 2: Preparation of test specimens and determination of properties (ISO 13000-2:2021); German version EN ISO 13000-2:2021

DIN EN ISO 13000-1:2021 塑料. 聚四氟乙烯(PTFE)半成品. 第1部分: 要求和名称与符号(ISO 13000-1-2021); 德文版本EN ISO 13000-1-2021

This part of ISO 13000 specifies the requirements and establishes a system of designation for processed unfilled polytetrafluoroethylene (PTFE) products, which may occur in several forms. The PTFE used to make the semi-finished product is described in ISO 20568 1 and, as provided

Plastics - Polytetrafluoroethylene (PTFE) semi-finished products - Part 1: Requirements and designation (ISO 13000-1:2021); German version EN ISO 13000-1:2021

UNI EN ISO 13000-2:2021 塑料 聚四氟乙烯（PTFE）半成品 第2部分：试样的制备和性能的测定

Plastics - Polytetrafluoroethylene (PTFE) semi-finished products - Part 2: Preparation of test specimens and determination of properties

UNI EN ISO 13000-1:2021 塑料 聚四氟乙烯（PTFE）半成品 第1部分：要求和名称

Plastics - Polytetrafluoroethylene (PTFE) semi-finished products - Part 1: Requirements and designation

ASTM D8366-21a 由未填充聚偏氟乙烯（PVDF）制成的挤压和压缩模制型材的标准规范

1.1 This specification covers the requirements and test methods for the material, dimensions, workmanship, and the properties of extruded sheet, rod and tubular bar manufactured from unfilled PVDF. 1.2 This specification covers the requirements and test methods for the material, dimensions, workmanship, and the properties of extruded and compression molded shapes manufactured from unfilled PVDF. 1.3 The properties included in this specification are those required for shapes made from PVDF polymers. Requirements necessary to identify particular characteristics of the shape are included in Section 5. 1.4 This specification allows for the use of up to 20 % process regrind and reprocessed plastic, total, and of uncontaminated quality. 1.5 The values stated in English Units are to be regarded as the standard in all property and dimensional tables. For reference purposes, SI units are also included. 1.6 The following safety hazards caveat pertains only to the test method or test methods described in this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Extruded and Compression Molded Shapes Made from Unfilled Poly(Vinylidene Fluoride) PVDF

KS M ISO 13000-1-2021 塑料 聚四氟乙烯（PTFE）半成品 第1部分：要求和名称

Plastics－Polytetrafluoroethylene(PTFE) semi-finished products－Part 1：Requirements and designation

T/CSEM 0005-2021 便携式无源冷藏应急保温包

便携式无源冷藏应急保温包是一种方便便携、无需外部电源提供能量、仅依靠蓄冷剂和保温层对食品、药物等冷藏保温的装置。该装置可确保应急救援物品（食品、生物试剂和原材料等）在保温运送过程的质量安全，在应急救援中发挥重要作用。我国是地质灾害频发的国家之一，在突发性自然灾害发生时，该便携式无源冷藏应急保温包可替代大型机械设备将具有低温冷藏需求的应急救援物品快速送达，此外，在交通不发达区域，便携式无源冷藏应急保温包可实现多方位、门到门的配送服务，解决最后一公里问题。 近年来，由于箱体保温材料和蓄冷剂的快速发展，以及物联网技术的引入，便携式无源冷藏应急保温包更新换代频繁，市面上流通的产品种类繁多。然而国内尚无统一的产品标准，各厂商出厂依据的标准不一，各检测机构的检测方法各异，导致整个无源冷藏应急保温包行业相对混乱。因此，有必要对无源冷藏应急保温包进行标准约束。 本文件通过外观、保温性能、蓄冷剂、温度监控设备和理化性能5个方面对便携式无源冷藏应急保温包进行要求，重点强调保温时限测定试验，规范便携式无源冷藏应急保温包的产品质量标准，促进行业有序、良性发展。

Portable Passive Refrigerated Emergency Insulation Kit

T/CBMF 131-2021*T/CSTE 0033-2021 “领跑者”标准评价要求 聚氯乙烯 弹性地板

本文件规定了聚氯乙烯弹性地板“领跑者”标准评价的术语和定义、评价指标体系和等级划分。 本文件适用于硬质聚氯乙烯弹性地板、半硬质聚氯乙烯弹性地板、同质聚氯乙烯弹性地板和非同质聚氯乙烯弹性地板的企业标准水平评价。相关机构在制定企业标准“领跑者”评估方案时可参考使用本文件。企业在制定企业标准时也可参照使用。

Assessment requirements for forerunner standards—Polyvinyl chloride resilient floor

BS EN ISO 13000-2:2021 塑料 聚四氟乙烯（PTFE）半成品 测试样品的制备和性能测定

Plastics. Polytetrafluoroethylene (PTFE) semi-finished products. Preparation of test specimens and determination of properties

BS EN ISO 13000-1:2021 塑料 聚四氟乙烯（PTFE）半成品 要求和指定

Plastics. Polytetrafluoroethylene (PTFE) semi-finished products. Requirements and designation

DS/EN ISO 13000-2:2021 塑料《聚四氟乙烯（PTFE）半成品》第2部分：试样制备及性能测定（ISO 13000-2:2021）

Plastics – Polytetrafluoroethylene (PTFE) semi-finished products – Part 2: Preparation of test specimens and determination of properties (ISO 13000-2:2021)

DS/ISO 13000-1:2021 塑料《聚四氟乙烯（PTFE）半成品》第1部分：要求和标志

Plastics – Polytetrafluoroethylene (PTFE) semi-finished products – Part 1: Requirements and designation

DS/EN ISO 13000-1:2021 塑料《聚四氟乙烯（PTFE）半成品》第1部分：要求和标志（ISO 13000-1:2021）

Plastics – Polytetrafluoroethylene (PTFE) semi-finished products – Part 1: Requirements and designation (ISO 13000-1:2021)

DS/ISO 13000-2:2021 塑料《聚四氟乙烯（PTFE）半成品》第2部分：试样制备及性能测定

Plastics – Polytetrafluoroethylene (PTFE) semi-finished products – Part 2: Preparation of test specimens and determination of properties

NF T51-550-1*NF EN ISO 13000-1:2021 塑料 聚四氟乙烯（PTFE）半成品 第1部分：要求和名称

Plastics - Polytetrafluoroethylene (PTFE) semi-finished products - Part 1 : requirements and designation

T/ZZB 2379-2021 聚亚苯基砜（PPSU）婴幼儿水杯

本文件规定了聚亚苯基砜（PPSU）婴幼儿水杯（以下简称“水杯”）的术语和定义、基本要求、技术要求、试验方法、检验规则、包装、标志、运输和贮存、质量承诺。 本文件适用于水杯杯身以聚亚苯基砜树脂为主要原料，其他配件以热塑性塑料、硅橡胶为主要原料，经加工制成的带有保护盖的婴幼儿用水杯。

Polyphenylene sulfone resins (PPSU) cups for infants

UL 746C-2021

1.1 These requirements cover parts made of polymeric materials that are used in electrical equipment and describe the various test procedures and their use in the testing of such parts and equipment. 1.2 These requirements do not cover the specific insulating systems that are covered by the requirements contained in the Standard for Systems of Insulating Materials, General, UL 1446. 1.3 Test procedures are provided herein for the evaluation of polymeric materials in specific applications. These test procedures include references to data obtained from small-scale property tests conducted under standard conditions as well as other practical means of evaluation. This new edition also includes revisions for the Clarification of End-Product Flammability Tests and some other general editorial revisions as proposed in the August 8, 2003 bulletin.

6/13/2001 (20p), 6/6/2001 (18p), 4/3/2001 (10p), 3/20/2001 (6p)