83.140.10 薄膜和薄板 标准查询与下载

T/WS 0006-2023 锂电池用阻燃聚丙烯麦拉膜

力学性能 项 目　要  求 拉伸强度，MPa　纵向　≥29          横向　≥27 断裂伸长率，%　        纵向　≥480        横向　≥430 穿刺强度，N/mm　≥80 浸润张力a(电晕后，背胶面)，mN/m　≥38 a   浸润张力仅适用于电晕麦拉膜。 电气性能 项 目　要 求 介电强度，kV/mm　≥65 体积电阻率，Ω·cm　≥1×1016 表面电阻率，Ω　≥5×1014

Flame retardant polypropylene Mai La film for lithium-ion battery

T/CIPR 067-2023 大通量加强型聚偏氟乙烯（PVDF）不带衬超滤膜

本文件规定了大通量加强型聚偏氟乙烯（PVDF）不带衬超滤膜的术语和定义、技术要求、试验方法、检验规则、标志、包装、运输和贮存。 本文件适用于各种大通量加强型聚偏氟乙烯（PVDF）不带衬超滤膜的制造技术，其他不同类型的滤膜可参照使用。

Large-flux reinforced polyvinylidene fluoride (PVDF) unlined ultrafiltration membrane

T/CIPR 057-2023 纸尿裤抗菌塑料包装袋

本文件规定了纸尿裤抗菌塑料包装袋的术语和定义、分类、技术要求、试验方法、检验规则、标志、包装、运输和贮存。 本文件适用于纸尿裤包装用的抗菌塑料包装袋。

Diaper antibacterial plastic packaging bag

T/SHPTA 038-2023 光伏背板用聚酯薄膜

本标准适用于光伏背板用聚酯薄膜

Polyester film for photoelectric display

T/SHBX 001-2023 《工业包装用无溶剂铝塑复合膜、袋》

本文件规定了工业包装用无溶剂铝塑复合膜、袋的分类、要求、试验方法、检验规则、标志、包装、运输和贮存。

Solventless aluminum foil-plastic laminated film and pouch for commerce packaging

ASTM D2578-23 聚乙烯和聚丙烯薄膜润湿张力的标准试验方法

1.1 This test method covers the measurement of the wetting tension of a polyethylene or polypropylene film surface in contact with drops of specific test solutions in the presence of air. 1.2 The values stated in SI units are to be regarded as standard. The values given in parentheses are mathematical conversions to inch-pound units that are provided for information only and are not considered standard. NOTE 1—This test method and the specified reagents were specifically developed for polyethylene and polypropylene films. It is possible to utilize this test method and the specified reagents for films composed of other polymers, but this can affect the surface energies of the gas-liquid and solid-liquid interfaces, which will affect the contact angle and wetting tension. The applicability and significance for use of non-polyolefin materials must be established by the user. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Specific hazards statements are given in Section 9. NOTE 2—This test method is equivalent to ISO 8296. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Wetting Tension of Polyethylene and Polypropylene Films

ASTM E720-23 电子辐射硬度试验中中子光谱测定用中子传感器的选择和使用标准指南

1.1 This guide covers the selection and use of neutronactivation detector materials to be employed in neutron spectra adjustment techniques used for radiation-hardness testing of electronic semiconductor devices. Sensors are described that have been used at many radiation hardness-testing facilities, and comments are offered in table footnotes concerning the appropriateness of each reaction as judged by its cross-section accuracy, ease of use as a sensor, and by past successful application. This guide also discusses the fluence-uniformity, neutron self-shielding, and fluence-depression corrections that need to be considered in choosing the sensor thickness, the sensor covers, and the sensor locations. These considerations are relevant for the determination of neutron spectra from assemblies such as TRIGAand Godiva-type reactors and from Californium irradiators. This guide may also be applicable to other broad energy distribution sources up to 20 MeV. NOTE 1—For definitions on terminology used in this guide, see Terminology E170. 1.2 This guide also covers the measurement of the gammaray or beta-ray emission rates from the activation foils and other sensors as well as the calculation of the absolute specific activities of these foils. The principal measurement technique is high-resolution gamma-ray spectrometry. The activities are used in the determination of the energy-fluence spectrum of the neutron source. See Guide E721. 1.3 Details of measurement and analysis are covered as follows: 1.3.1 Corrections involved in measuring the sensor activities include those for finite sensor size and thickness in the calibration of the gamma-ray detector, for pulse-height analyzer deadtime and pulse-pileup losses, and for background radioactivity. 1.3.2 The primary method for detector calibration that uses secondary standard gamma-ray emitting sources is considered in this guide and in Test Methods E181. In addition, an alternative method in which the sensors are activated in the known spectrum of a benchmark neutron field is discussed in Guide E1018. 1.3.3 A data analysis method is presented which accounts for the following: detector efficiency; background subtraction; irradiation, waiting, and counting times; fission yields and gamma-ray branching ratios; and self-absorption of gamma rays and neutrons in the sensors. 1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Guide for Selection and Use of Neutron Sensors for Determining Neutron Spectra Employed in Radiation-Hardness Testing of Electronics

ASTM F736-17(2023) 用落锤法测定整体聚碳酸酯板抗冲击性的标准试验方法

1.1 This test method covers the determination of the energy required to initiate failure in monolithic polycarbonate sheet material under specified conditions of impact using a free falling weight. 1.2 Two specimen types are defined as follows: 1.2.1 Type A consists of a flat plate test specimen and employs a clamped ring support. 1.2.2 Type B consists of a simply supported three-point loaded beam specimen (Fig. 1) for use with material which can not be failed using the Type A specimen. For a maximum drop height of 6.096 m (20 ft) and a maximum drop weight of 22.68 kg (50 lb), virgin polycarbonate greater than 12.70 mm (1⁄2 in.) thick will require use of the Type B specimen. NOTE 1—See also ASTM Methods: D1709, D2444 and D3029. 1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3.1 Exception—The inch-pound units in parentheses are provided for information only. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific hazard statement, See Section 7. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Impact Resistance of Monolithic Polycarbonate Sheet by Means of a Falling Weight

T/SHBX 014-2022 包装用铝塑复合膜、袋

Aluminum-plastic composite film and bag for packaging

T/ZZB 2877-2022 热封型双向拉伸聚丙烯（BOPP）薄膜

本文件规定了热封型双向拉伸聚丙烯（BOPP）薄膜（以下简称“薄膜”）的术语和定义、基本要求、技术要求、试验方法、检验规则、标志、包装、运输及贮存和质量承诺。 本文件适用于以聚丙烯为主要原料，用平膜法经双向拉伸成型制得的单面热封型聚丙烯薄膜。 本文件不适用于其他特殊功能的双向拉伸聚丙烯薄膜，如双向拉伸聚丙烯消光薄膜、双向拉伸聚丙烯珠光薄膜、双向拉伸聚丙烯拉线用薄膜、双向拉伸聚丙烯电容器用薄膜、双向拉伸聚丙烯香烟包装薄膜等。

Biaxially oriented polypropylene（BOPP） film for heat sealing

T/SHBX 013-2022 《耐穿刺、高阻隔塑料复合薄膜及包装袋》

本文件规定了耐穿刺、高阻隔塑料复合薄膜及包装袋的术语和定义、缩略语、分类、要求、试验方法、检验规则、标志、包装、运输和贮存。

Puncture resistant and high barrier plastic composite film and packaging bag

T/SHPTA 030-2022 民用航空器用聚氟乙烯基阻燃耐候复合装饰膜

本文件适用于民用航空器内，尤其是大中小型客机的舱内装饰应用。 

Polyvinyl-fluoride?flame-retardant & weathering-resistant decorative laminates for civil aviation

T/IGIA 011-2022 高阻隔吨袋 内袋用塑料与铝箔复合膜

本标准规定了高阻隔吨袋内袋用塑料与铝箔复合膜的要求、试验方法、检验规则、标志、包装、运输和贮存。

Plastic and aluminum foil composite film for high barrier ton bag inner bag

T/IGIA 012-2022 高阻隔吨袋 内袋用塑料与铝箔复合膜 售后服务规范

本标准规定了高阻隔吨袋内袋用塑料与铝箔复合膜售后服务的基本原则、服务制度、服务人员、服务提供、服务范畴、服务评价等。

Specification for after-sales service of inner bag with Plastics and aluminum foil laminated films for high barrier ton bag

T/SHBX 012-2022 《食品包装用耐蒸煮复合膜、袋》

本文件规定了食品包装用耐蒸煮复合膜、袋的缩略语、符号、术语和定义、分类、要求、试验方法、检验规则、标志、包装、运输和贮存。

Laminated retort films and pouches for food packaging

BS EN 15354:2022 塑料 由增塑聚氯乙烯（PVC-P）制成的挤出和/或压延非增强薄膜和片材 特性和名称

This document specifies the characterization and the designation of extruded and/or calendered, non- reinforced film or sheeting made of plasticized poly(vinyl chloride) (PVC-P). It specifies the corresponding test methods for the assessment of the characteristics. This document is applicable to film and sheeting in the range of thickness from 0,05 mm to 1 mm.

Plastics. Extruded and/or calendered, non-reinforced film and sheeting made of plasticized poly(vinyl chloride) (PVC-P). Characterization and designation

ASTM D2291/D2291M-22 玻璃树脂复合材料环形试样的制造

1.1 This practice is intended for use in the fabrication of ring-type test specimens to be used in the evaluation of the mechanical properties of reinforcement and resins in a composite structure. The practice outlines the steps in the preparation of the test specimens, including the final specimen machining where applicable. Three final ring configurations are included. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. NOTE 1—There is no known ISO equivalent to this practice. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for Fabrication of Ring Test Specimens for Glass-Resin Composites

T/CASME 47-2022 聚苯乙烯（PS）棱镜防眩光板

本文件规定了聚苯乙烯（PS）棱镜防眩光板技术要求、试验方法、检验规则、标志、包装、运输及贮存。

Polystyrene (PS) prism anti glare plate

T/SHBX 007-2022 《包装用尼龙共挤膜》

本文件规定了包装用尼龙共挤膜的产品分类、要求、试验方法、检验规则、标识标志、包装、运输、贮存等。

Nylon co-extruded Lamination Films For Packaging

T/SHPTA 027-2022 包装用尼龙共挤膜

本文件规定了包装用尼龙共挤膜的产品分类、要求、试验方法、检验规则、标识标志、包装、运输、贮存等。

Nylon co-extruded Lamination Films For Packaging