91.140.70 卫生设备 标准查询与下载

T/CBCSA 7-2019 卫生洁具 直角阀

本标准规定了直角阀的术语和定义、分类、材料、技术要求、试验方法、检验规则、标志、包装、使用说明、运输和贮存。 本标准适用于安装在建筑物内的冷、热水供水管路中间、工作压力（静压）不大于1.0MPa、介质温度为4℃～90℃、与卫生洁具进水装置配套使用的直角阀。

Sanitary Ware Right Angle Valve

T/CBCSA 10-2019 卫生洁具 水嘴

本标准规定了水嘴的术语和定义、分类、材料、配套装置、要求、试验方法、检验规则、标志、包装、运输和贮存。 本标准适用于公称尺寸为DN10、DN15、DN20、DN25，工作压力（静压）不大于1.0MPa、供水温度4℃~90℃条件下使用、安装在建筑物内的冷热水供水管路未端上各种结构的水嘴。

sanitary ware faucet

T/CBCSA 8-2019 卫生洁具 淋浴器

本标准规定了淋浴器产品的术语和定义、分类、材料、技术要求、试验方法、检验规则、标志、包装、运输和贮存。 本标准适用于公称压力不大于1.0MPa，水介质温度为（4～90）℃条件下，安装于建筑物内使用的机械混合式淋浴器、温控淋浴器。不适用于特殊用途的淋浴器产品。

sanitary ware shower

T/CBCSA 9-2019 卫生洁具 软管

本标准规定了软管产品的术语和定义、分类及代号、材料、技术要求、试验方法、检验规则、标志、标识、包装、运输和贮存。 本标准适用于工作压力不大于1.0 MPa，供水温度不超过90℃的卫生洁具用软管。

Sanitary Ware Hose

T/CBCSA 6-2019 淋浴房

前??言　 1　范围　 2　规范性引用文件　 3　术语和定义　 4　材料　 5　技术要求　 6　试验方法　 7　检验规则　 8　标志、包装、运输和贮存　

Shower enclosures

19/30393869 DC BS EN 16578.陶瓷卫生器具产品类别规则

BS EN 16578. Product Category Rules for ceramic sanitary appliances

ASTM F3202-19a 连接波纹壁高密度聚乙烯（PE）和聚丙烯（PP）管道用实心壁聚氯乙烯配件的标准规范

1.1 This specification covers requirements and test methods for 6 in. (150 mm) through 60 in. (1500 mm) fabricated or molded solid wall poly(vinyl chloride) (PVC) gasketed sanitary sewer fittings to be used with piping manufactured to Specifications F2763, F2764, or F2947. Fabricated fittings may be manufactured from pipe, or from a combination of pipe and injection molded parts with PVC base stock. 1.2 The requirements of this specification are to provide fabricated or molded solid wall PVC gasketed fittings for nonpressure drainage of sewage. 1.3 Fittings produced to this specification are intended to be installed with pipe, in accordance with Practice D2321. 1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Solid Wall Poly (Vinyl Chloride) PVC Fittings for Joining Corrugated Wall High Density Polyethylene (PE) and Polypropylene (PP) Piping

BS EN 33:2019 马桶和卫生间套件 连接尺寸

What is BS EN 33 - Connecting dimensions for WC Pans about?   There are very few things more unpleasant than a leaky WC suite. Connecting points for WC pans and WC suites need to adhere to the highest quality standards. BS EN 33 specifies the connecting dimensions of WC pans and WC suites, regardless of the materials used for their manufacture.   Note:  BS EN 33 does not apply to siphonic action WC pans and WC suites.  Who is BS EN 33 - Connecting dimensions for WC Pans for?   

WC pans and WC suites. Connecting dimensions

T/CBCSA 15-2019 智能坐便器

本标准规定了智能坐便器的术语和定义、分类、通用要求、使用功能、性能、电气及功能安全、试验方法、检验规则、标志和标识、使用说明、包装、运输和贮存。 本标准适用于智能坐便器。智能坐便器的清洗系统供水水质应符合GB 5749的规定，不应使用中水。

Samart toilet

ASTM F3202-19 连接波纹壁高密度聚乙烯（PE）和聚丙烯（PP）管道用实心壁聚氯乙烯配件的标准规范

Standard Specification for Solid Wall Poly (Vinyl Chloride) PVC Fittings for Joining Corrugated Wall High Density Polyethylene (PE) and Polypropylene (PP) Piping

DB42/T 1495-2019 农村无害化厕所建造技术指南

Technical Guidelines for Construction of Harmless Toilets in Rural Areas

ASTM F446-19 安装在洗浴区的扶手杆和附件的消费者安全标准规范

1.1 This consumer safety specification covers performance requirements, test methods, and levels of performance to ensure satisfactory functioning of the grab bars and accessory items (not including plumbing controls) during reasonable use to assist a person entering, leaving, or moving within the bathing area. 1.2 This consumer safety specification is intended to reduce the number of accidents by specifying requirements for grab bars and accessories designed to decrease the probability of slips and falls. 1.3 This consumer safety specification does not address the specific need of gang showers, island tubs, peninsula tubs, sunken tubs, or tubs 6 ft (1.8 m) or longer. 1.4 This consumer safety specification exempts shower stalls with both interior dimensions of 34 in. (864 mm) or less. 1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.6 The following precautionary caveat pertains only to the test method portion, Section 7, of this specification. This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Consumer Safety Specification for Grab Bars and Accessories Installed in the Bathing Area

BS EN 17125:2018 国内水疗中心/漩涡水疗中心/热水浴缸 安全要求及测试方法

What is BS EN 17125  -  Domestic spas/whirlpool spas/hot tubs about?    BS EN 17125 discusses domestic spas/whirlpool spas/hot tubs. BS EN 17125 specifies safety requirements and test methods for domestic spas/whirlpool spas/hot tubs for indoor and/or outdoor use, covering the following:   Portable spas including inflatable spas   Exercise spas (factory-built or field-engineered)    Scandinavian hot tubs, field-engineered spas   Any associated equipment   ...

Domestic spas/whirlpool spas/hot tubs. Safety requirements and test methods

DB11/T 343-2018 节水器具应用技术标准

Technical standards for water-saving appliances

DIN EN 997:2018 带整体存水弯的马桶和马桶套件；德文版 EN 997:2018

This European Standard specifies constructional and performance characteristics together with test methods for close-coupled suites, one-piece and independent WC pans with integral trap used for personal hygiene manufactured from glazed ceramics or stainless steel. This standard does not apply to squatting toilets, WC pans without integral trap or flushing cisterns as separate appliances. In the case of independent WC pans, the associated flushing cisterns and pressure valves are covered by other standards and the reference to cisterns in this standard is related only to the definition and requirements of flushing volume.In the case of close-coupled suites and one-piece WCs, this standard also specifies design, performance requirements and the test methods for designated flushing cisterns with flushing mechanisms, inlet valves and overflows. For these products, this standard covers flushing cisterns designed to be connected to drinking water installations inside buildings. Before installation of WCs, EN 12056-2 and national requirements need to be taken into consideration.

WC pans and WC suites with integral trap; German version EN 997:2018

DIN EN 14296:2018 卫生用具 公用洗涤槽；德文版 EN 14296:2015+A1:2018

This document specifies characteristics for the cleanability, load resistance and durability of communal washing troughs used for domestic purposes.

Sanitary appliances - Communal washing troughs; German version EN 14296:2015+A1:2018

T/ZZB 0804-2018 城乡排水用共聚聚丙烯塑料检查井-井座

本标准规定了城乡排水用共聚聚丙烯塑料检查井-井座(以下简称“井座”)的术语和定义、符号和缩略语、分类及标记、基本要求、技术要求、试验方法、检验规则、标志、包装、运输和贮存以及质量承诺。 本标准适用于城乡排水排污用，井底埋深不大于6 m，埋地管径不大于600 mm的共聚聚丙烯塑料检查井-井座。

Co-polypropylene plastic inspection well for urban and rural drainage-well seat

T/ZZB 0829-2018 食品添加剂 植物炭黑

本标准规定了食品添加剂植物炭黑（以下简称植物炭黑）的术语和定义、基本要求、技术要求、试验方法、检验规则、标签、标志、包装、运输、贮存和质量承诺。 本标准适用于以植物炭化料为原料，经预处理（挑选、清洗、烘干）、粉碎、包装而成的食品添加剂植物炭黑。 化学名称：碳 分子式：C CAS号：7440-44-0 相对分子量：12.01（按2007年国际相对原子质量）

Food additive-Vegetable carbon

ASTM A1111-18 自流管道排水、废物和通风卫生设施用铸铁污水管和配件用铸铁壁橱法兰的标准规范

Standard Specification for Cast Iron Closet Flanges for Use With Cast Iron Soil Pipe and Fittings in Gravity Flow Plumbing Drain, Waste, and Vent Sanitary Applications

ISO 30500:2018 无污水卫生系统.预制综合处理装置.设计和试验的一般安全和性能要求

This document specifies general safety and performance requirements for design and testing as well as sustainability considerations for non-sewered sanitation systems (NSSS). A NSSS, for the purposes of this document, is a prefabricated integrated treatment unit, comprising frontend (toilet facility) and backend (treatment facility) components that a) collects, conveys, and fully treats the specific input within the system, to allow for safe reuse or disposal of the generated solid, liquid, and gaseous output, and b) is not connected to a networked sewer or networked drainage systems. This document is applicable to sanitation systems that are either manufactured as one package, or manufactured as a set of prefabricated elements designed to be assembled in one location without further fabrication or modification that influences the system function. The plane or surface (e.g. flooring, concrete pad) upon which a fully assembled NSSS is situated is beyond the scope of this document. This document is not applicable to sanitation systems constructed in situ. This document also covers NSSS backend components that are designed to be integrated with one or more specified frontends. Although this document is primarily applicable to the development of sanitation systems that are not connected to water and electricity networks, it can also be applied to systems that can utilize water mains and/or electricity. This document defines the basic treatable input as primarily human excreta and gives options for extending the range of input substances. Requirements for the quality of the outputs from the sanitation system are given for solid and liquid discharges as well as odour, air, and noise emissions. It contains criteria for the safety, functionality, usability, reliability, and maintainability of the system, as well as its compatibility with environmental protection goals. This document does not encompass the following aspects: — guidelines for selection, installation, operation and maintenance, and management of sanitation systems; — transportation of treated output outside of the sanitation system (e.g. manual transport, transportation by truck or trunk pipes) for further processing, reuse, or disposal; — treatment processes taking place at another location separate from that of the frontend and backend components; — reuse and disposal of sanitation system output.

Non-sewered sanitation systems — Prefabricated integrated treatment units — General safety and performance requirements for design and testing