91.140.80 排水系统 标准查询与下载

T/CECS 94-2019 建筑排水内螺旋管道工程技术规程

本规程共分6章，主要内容包括：总则、术语、管材和管件、设计、施工安装和验收。

Technical specification of inner spiral rib pipe for building drainage

T/SFSF 000003-2019 餐饮用油水分离器

本标准规定了餐饮用油水分离器（以下简称“油水分离器”)的术语和定义、要求、试验方法、检验规则、标志、使用说明、包装、运输及贮存。 本标准适用于动植物油初始浓度含量不大于800mg/L；悬浮物浓度不大于600mg/L的餐饮用油水分离器的设计、生产、安装、调试、使用。

Grease-water separator in catering

ASTM F2764/F2764M-19 6至60英寸[150至1500 mm]聚丙烯（PP）波纹双管和三壁管道及适用于非压力卫生下水道应用的管件的标准规格

1.1 This specification covers requirements and test methods for corrugated double and triple wall polypropylene pipe and fittings. The nominal inside diameters covered are 6 to 60 in. [150 to 1500 mm]. 1.2 The requirements of this specification are intended to provide pipe and fittings for underground use for non-pressure sanitary sewer systems. Pipe and fittings produced in accordance with this specification shall be installed in compliance with Practice D2321. 1.3 This specification covers pipe and fittings with an annular corrugated wall and an essentially smooth interior wall (that is, double wall) (Fig. 1) and pipe and fittings with an annular corrugated wall and an essentially smooth interior and exterior wall (that is, triple wall) (Fig. 2). 1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.5 The following precautionary statement applies only to Section 7 of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for 6 to 60 in. [150 to 1500 mm] Polypropylene (PP) Corrugated Double and Triple Wall Pipe and Fittings for Non-Pressure Sanitary Sewer Applications

T/AHGY 0003-2019 装配式三瓮化粪池技术要求

本标准规定了装配式三瓮化粪池的术语和定义、基本要求、规格型号、要求、试验方法、检验规则、标志、运输和储存。 本标准适用于村镇旱厕改造用容积不超过3m3的装配式三瓮化粪池（以下简称化粪池），污水改造等其他用途亦可以参照使用。

Technical requirements for prefabricated three-urn septic tank

DB11/T 1594-2018 城镇排水管道检查技术规程

Technical regulations for inspection of urban drainage pipelines

DB11/T 1593-2018 城镇排水管道维护技术规程

Technical regulations for maintenance of urban drainage pipes

T/AHGY 0001-2018 装配式三格化粪池技术要求

本标准规定了装配式三格化粪池的术语和定义、基本要求、规格型号、要求、试验方法、检验规则、标志、运输和储存。 本部分适用于村镇旱厕改造用装配式三格化粪池，污水改造等其他用途亦可以参照使用。

Technical requirements for prefabricated three-compartment septic tank

T/AHGY 0002-2018 装配式双瓮化粪池技术要求

本标准规定了装配式双瓮化粪池的术语和定义、基本要求、规格型号、要求、试验方法、检验规则、标志、运输和储存。 本部分适用于村镇旱厕改造用装配式双瓮化粪池，污水改造等其他用途亦可以参照使用。

Technical requirements for prefabricated double vat septic tank

DB35/T 1803-2018 井盖物联网技术规范

本标准规定了井盖物联网的体系结构、通信协议，井盖智能终端的技术要求和测试方法。 本标准适用于城市井盖物联网的设计、井盖智能终端的设计和测试，农村井盖物联网建设也可参考使用。

Manhole Cover Internet of Things Technical Specifications

ASTM F2764/F2764M-18a 6至60英寸[150至1500 mm]聚丙烯（PP）波纹双管和三壁管道及适用于非压力卫生下水道应用的管件的标准规格

Standard Specification for 6 to 60 in. [150 to 1500 mm] Polypropylene (PP) Corrugated Double and Triple Wall Pipe and Fittings for Non-Pressure Sanitary Sewer Applications

BS EN 12405-1:2018 煤气表. 换算装置. 体积换算

Gas meters. Conversion devices. Volume conversion

ASTM F2764/F2764M-18 6至60英寸[150至1500 mm]聚丙烯（PP）波纹双管和三壁管道及适用于非压力卫生下水道应用的管件的标准规格

Standard Specification for 6 to 60 in. [150 to 1500 mm] Polypropylene (PP) Corrugated Double and Triple Wall Pipe and Fittings for Non-Pressure Sanitary Sewer Applications

CAN/CSA-B127.3-2018 纤维水泥排水管、废水管和通风管及管件

1 Scope 1.1 This Standard covers fibrocement Type 1 (Class 3000) and Type 2 (Class 4000) pipe and pipe fittings for installation in gravity-flow systems inside and outside of buildings, above and below grade. 1.2 This Standard includes specifications for material, dimensions, crushing strength, chemical resistance, and joint tightness. Methods of marking to indicate compliance with these requirements are included. Recommended installation practice is given in Annex A. Suitability of material composition is given in Annex B. 1.3 The values given in SI units are the units of record for the purposes of this Standard. The values given in parentheses are for information and comparison only. 1.4 In this Standard, “shall” is used to express a requirement, i.e., a provision that the user is obliged to satisfy in order to comply with the standard; “should” is used to express a recommendation or that which is advised but not required; and “may” is used to express an option or that which is permissible within the limits of the Standard. Notes accompanying clauses do not include requirements or alternative requirements; the purpose of a note accompanying a clause is to separate from the text explanatory or informative material. Notes to tables and figures are considered part of the table or figure and may be written as requirements. Annexes are designated normative (mandatory) or informative (non-mandatory) to define their application.

Fibrocement drain, waste, and vent pipe and pipe fittings

DB3301/T 0213-2018 城市道路防沉降检查井盖和雨水口技术管理规范

本规范规定了杭州市城市道路防沉降检查井盖和雨水口的术语与定义、分类、检查井盖外观和标识、日常维护、应急处置、产品质量选用等。 本规范适用于新建、改建城市道路机动车道和非机动车道范围内各类地下管线防沉降检查井盖、雨水口设计和技术管理。

Specifications for technical management of urban road subsidence inspection manhole covers and gullies

DB37/T 5107-2018 城镇排水管道检测与评估技术规程

本规程适用于山东省城镇排水管道及其附属构筑物的检测与评估。

Technical specification for inspection and evaluation of urban drainage pipelines

DB21/T 1917-2018 建筑同层排水工程技术规程

Technical specification for building same-floor drainage engineering

CJ/T 270-2017 聚乙烯塑钢缠绕排水管及连接件

本标准规定了用钢带与聚乙烯（中密度或高密度）通过挤出方式成型的塑钢复合带材，经缠绕焊接制成的塑钢缠绕排水管的术语和定义、符号、代号，材料，产品结构、分类和连接方式，要求，试验方法，检验规则，标志、运输、贮存。 该管材适用于长期输送介质温度在45℃以下的无压埋地城镇排水、工业排水以及农田排水等工程。

Steel reinforced spirally wound Polyethylene(PE) drainage pipe

DB34/T 2978.2-2017 装配式化粪池技术要求 第2部分：双瓮式

DB34/T 2978 的本部分规定了装配式双瓮化粪池的术语和定义、基本要求、规格型号、要求、试验 方法、检验规则、标志、运输和储存。 本部分适用于村镇旱厕改造用装配式双瓮化粪池（以下简称化粪池），污水改造等其他用途亦可以 参照使用

Technical requirements for prefabricated septic tanks Part 2: Double urn type

DB34/T 2978.1-2017 装配式化粪池技术要求 第1部分：三格式

DB34/T 2978 的本部分规定了装配式三格化粪池的术语和定义、基本要求、规格型号、要求、试验 方法、检验规则、标志、运输和储存。 本部分适用于村镇旱厕改造用装配式三格化粪池（以下简称化粪池），污水改造等其他用途亦可以 参照使用

Technical requirements for prefabricated septic tanks Part 1: Three formats

DIN EN 1253-5:2017 建筑物用集水沟.第5部分:可截流轻液体的集水沟;德文版本EN 1253-5-2017

Gullies for buildings - Part 5: Gullies with light liquids closure; German version EN 1253-5:2017