97.220.10 标准查询与下载

DB62/T 2988-2019 运动场地合成材料面层原材料使用规范

Specifications for the use of raw materials for synthetic material surfaces in sports venues

ASTM F2000-19 棒球场和垒球场用栅栏的标准安全性能规范

1.1 This specification provides recommended minimum requirements for various types of fences used in softball and baseball ballfields and other sports facilities, and practices for installation. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Safety Performance Specification for Fences for Baseball and Softball Fields

BS EN 14974:2019 滑板公园 安全要求及测试方法

This standard applies to facilities for users of inline-skates, roller skates, skateboards or similar roller sports equipment, as well as BMX cycles (hereinafter referred to as facility/facilities). It specifies general and specific requirements and test methods for facilities used in unsupervised areas. The purpose of this European Standard is to specify the safety requirements, which to a large extent protect users and third parties (e.g. spectators) from hazards when using a facility as intended or as can be reasonably expected.

Skateparks. Safety requirements and test methods

BS EN 17164:2018 在公众游泳池水域使用的攀岩/抱石墙 安全和操作要求

What is BS EN 17164 about?    BS EN 17164 discusses climbing/bouldering walls for use in the water area of swimming pools. BS EN 17164 specifies safety requirements for climbing/bouldering walls, which are vertical and/or overhanging towards the water area, for use in the water area of swimming pools for public use in addition to the general safety requirements of EN 13451-1.     It also specifies requirements for the use, operation, and maintenance.    BS EN 17164 is applicable to climbing/bouldering walls in classified swimming pools as specified in

Climbing/bouldering walls for use in the water area of swimming pools of public use. Safety and operational requirements

BS EN 15288-2:2018 供公众使用的游泳池 操作安全要求

What is BS EN 15288 ‑ 2 about?    BS EN 15288 ‑ 2 is the second part of the multi-series international standard that discusses the safety aspects of the swimming pool for public use.   BS EN 15288 ‑ 2 specifies safety requirements for the operation of the classified swimming pool for public use . It is for those concerned with the operation and management of classified swimming pools.

Swimming pools for public use. Safety requirements for operation

DIN 18035-4:2018 运动场 第4部分：运动草坪区域

This Standard applies to outdoor sports areas which are turfed. It does not apply to golf courses, riding areas or lawn tennis courts. NOTE For information on golf and riding facilities, see the FLL-guideline for the construction of golf courses and FLL-recommendations for the planning, construction and maintenance of riding arenas. Under certain conditions (e. g. Areas with special use, with sub-terrain heating, with armor Systems or areas that are either entirely or partially protected by a roof, whether permanently or temporarily) it must be consider whether the specifications of this draft standard can be applied.

Sports grounds - Part 4: Sports turf areas

DB36/T 1082-2018 体育场馆运营管理规范

Gym Operations Management Specifications

DIN 18032-3:2018 体育馆 体育馆和多用途大厅和房间 第3部分：防止投球的安全性测试

This standard describes the method by which the resistance of ceiling-, wall- and installation-components used in sports halls (e. g. wall and ceiling linings, doors, windows, ventilation grilles, lamps, switchs, sockets, clocks, etc.) to damage when hit by a ball or balls is tested in accordance with DIN 18032-1. It applies to all components that could be hit by balls used for basketball, fistball, football, handball, hockeyball, volleyball, tennis and by medicine balls. This standard does not apply to use by shockballs.

Sports halls - Halls and rooms for sports and multi-purpose use - Part 3: Testing of safety against ball throwing

ASTM F2060-00(2018) 运动场上保持凉爽季节草坪草的标准指南

1.1 This guide covers the minimum requirements for maintaining cool season turfgrasses used for natural surface athletic fields. Practices covered include mowing, fertilization, irrigation, core cultivation, overseeding, and pest management. 1.2 The decisions involved in maintaining a quality natural playing surface should consider soil types, local climate and other factors; therefore, it is recommended that you contact your local cooperative extension service for more specific information on soils, and grass species and cultivars adapted to your area. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Guide for Maintaining Cool Season Turfgrasses on Athletic Fields

ASTM F1815-11(2018) 运动场根区的饱和导水率、保水率、孔隙率和体积密度的标准试验方法

1.1 These test methods cover the measurements of saturated hydraulic conductivity, water retention, porosity (including distribution of capillary and air-filled porosity at a known soil suction), and bulk density on sand-based root zone mixes to be used for construction and topdressing of golf course putting greens including United States Golf Association (USGA) recommended greens, golf course tees, sand-based sports fields, or other highly trafficked turfgrass areas. These test methods are designed for sand-based mixes and are not intended for use with fine or medium textured soils, for example, sandy loams and loams. 1.2 The values stated in SI units are to be regarded as the standard. The inch-pound units given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Methods for Saturated Hydraulic Conductivity, Water Retention, Porosity, and Bulk Density of Athletic Field Rootzones

ASTM F2269-11(2018) 保持季节性草坪在运动场上的标准指南

1.1 This guide covers the minimum requirements for maintaining warm-season turfgrasses used for natural surface athletic fields. Practices covered include mowing, fertilization, irrigation, core cultivation, winter overseeding, pest management, and requirements for management of dormant turf winter overseeded with cool-season turf (see also Guide F2060). 1.2 The decisions involved in maintaining a quality natural playing surface should consider soil types, local climate and other factors. Therefore, it is recommended that you contact your local cooperative extension service for more specific information on soils, and grass species and cultivars adapted to your area. 1.3 The values stated in SI units are to be regarded as the standard. The values in parentheses are for information only. 1.4 This standard may involve hazardous materials, operations, and equipment. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Guide for Maintaining Warm Season Turfgrasses on Athletic Fields

ASTM F1647-11(2018) 运动场根区混合物有机物含量的标准试验方法

1.1 These test methods cover the determination of the percent organic matter of a putting green root zone mixture using a loss on ignition method or the Walkley Black method. These test methods are useful for quantifying the organic matter content of volume ratio mixed root zone mixes. Test Methods D2974 is recommended for peat and other organic soils. 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use, nor the disposal of hazardous waste that may be generated. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For a specific precautionary statement, see 8.2.6. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Methods for Organic Matter Content of Athletic Field Rootzone Mixes

18/30374737 DC BS EN 16713-2 国内游泳池 水系统 第 2 部分 循环系统 要求及测试方法

BS EN 16713-2. Domestic swimming pools. Water systems - Part 2. Circulation systems. Requirements and test methods

ASTM F2698-08(2018) 地上和地上溜冰公园设施用栅栏的标准指南

1.1 This guide provides recommended minimum requirements for denoting the various types of fences/barriers for skate parks and for inline skating or roller hockey rinks and extreme performance areas. 1.2 This guide provides the minimum requirements for the protection of the participants from intrusion of other activity users; from unauthorized and unsupervised use by users that could be harmed by unanticipated entry into the area and from falls into in-ground skate park area. 1.3 This guide provides for the safety of spectators from errant skateboard use. 1.4 The values stated in inch-pound units are to be regarded as the standard. The SI values in parentheses are provided for information purposes only. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Guide for Fences for Above-Ground and In-ground Skate Park Facilities

EN 13451-10:2018 游泳池设备.第10部分:跳水台、跳板及相关设备用附加的特殊安全性要求和试验方法

Swimming pool equipment - Part 10: Additional specific safety requirements and test methods for diving platforms@ diving springboards and associated equipment

ASTM F2699-08(2018) 商业和公共室外喷水/播放区域栅栏标准指南

1.1 This guide provides the recommended minimum requirements for various types of fences for commercial and public outdoor water spray/play areas. 1.2 This guide provides for the safety of occupants in water spray/play areas or zones as it pertains to vehicular intrusion as well as other participant intrusion, and for children containment or entry/exit. 1.3 This guide does not choose the product components for the fence system, the choice of which should be made by the operators of the water spray/play area space and their specification writers or drafters based upon their determination of the merits of the products that could be used. 1.4 The values stated in inch-pound units are to be regarded as the standard. The SI values stated in parentheses are provided for information purposes only. 1.5 This guide does not purport to address the aspect of safety within a water spray/play area or zone. It is the responsibility of the user of this guide to establish appropriate safety practices as related to the water spray/play area and determine the applicability of regulatory requirements prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Guide for Fences for Commercial and Public Outdoor Water Spray/Play Areas

ASTM F3146-18 橄榄球用草皮运动系统冲击衰减的标准试验方法

1.1 This standard establishes a test method to be used when testing a synthetic turf field’s impact attenuation property for assessing its suitability for rugby. 1.2 The surface being tested will be located indoors or outdoors and typically includes the entire surface, both within the boundary lines of the playing area and outside of it. Where non-turf surfaces exist within these areas, they shall be excluded from the scope of this standard, unless they are covered either permanently or temporarily with synthetic turf. 1.3 It is acceptable to use this test method, where appropriate, as a test method for laboratory based testing of synthetic turf surfaces. 1.4 The definition of a minimum performance requirement for this test method is outside of the scope of this standard. Where reference is made to a minimum requirement this is intended for demonstration and clarification purposes only. 1.5 This test method establishes a method of reporting test results. 1.6 The values stated in SI units are to be regarded as standard. Where values are given in parenthesis they are mathematical conversions to inch-pound units that are provided for information purposes only and are not considered standard. 1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Impact Attenuation of Turf Playing Systems Designated for Rugby

T/HSCA 001-2018 体育场馆钢结构检测与鉴定规程

本规程共分14个章节和1个附录，主要技术内容包括：总则、术语、基本规定、原材料检测、焊接工艺评定检验、外观质量检测、无损检测、体育场馆钢结构残余应力检测、高强螺栓检测、钢结构变形检测、防腐涂层检测、防火涂层检测、钢结构工程监测、既有体育场馆耐久性鉴定。

Regulation for Testing and Evaluation of Steel Structure in Stadium

DB2101/T 0005-2018 合成材料运动场地面层标准

Standard for Composite Playground Surfaces

ASTM F2157-09(2018) 合成表面跑道的标准规范

1.1 This specification establishes the minimum performance requirements and classification when tested in accordance with the procedures outlined within this specification. All documents referencing this specification must include classification required. 1.2 This specification does not imply that an injury cannot be incurred if the surface is found to be in compliance with this specification. 1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Synthetic Surfaced Running Tracks