97.220.10 标准查询与下载

DB3302/T 1043-2018 游泳场所服务规范

Service Specifications for Swimming Places

EN 14903:2018 运动场表面 室内使用的多功能运动地板系统 旋转摩擦力测定的试验方法

Surfaces for sports areas - Multi-sports floor systems for indoor use - Test method for determination of rotational friction

DIN EN 16837:2018 运动区域的表面 线性鞋/表面摩擦的测定；德文版 EN 16837:2018

This European Standard specifies a test method for the determination of shoe/surface friction of synthetic sports surfaces. The method can be used for the assessment of both indoor and outdoor sports surfaces. NOTE: This method is not considered suitable for long pile synthetic turf surfaces.

Surfaces for sports areas - Determination of linear shoe/surface friction; German version EN 16837:2018

ASTM F2707-10(2018)e1 用于游泳池 水疗中心 热水浴缸​​和流水池吸入阻塞的现场制造吸气排气系统的安全设计和安装的标准安全性能规范

1.1 This safety performance specification provides requirements for safety in design and installation when using a suction-limiting vent system for suction entrapment prevention in swimming pools, spas, hot tubs, or wading pools. 1.2 The purpose of the vent is to relieve the vacuum at the suction outlet(s) caused by any blockage of the suction outlet(s). The vent is intended to prevent body entrapment at the suction outlet(s) and may also mitigate limb entrapment. It is not intended to prevent other injuries caused by the suction outlet(s) such as hair entrapment, mechanical entrapment, or evisceration. 1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Safety Performance Specification for Safe Design and Installation of Field Fabricated Suction-Limiting Vent Systems for Suction Entrapment Prevention in Swimming Pools, Spas, Hot Tubs, and Wa

ASTM F2461-18 水上游乐设备制造 建造 操作和维护的标准实施规程

Standard Practice for Manufacture, Construction, Operation, and Maintenance of Aquatic Play Equipment

BS EN 16837:2018 运动区域的表面 线性鞋/表面摩擦力的测定

What is this BS EN 16837 - Determination of linear shoe/surface friction about?    BS EN 16837 discusses surfaces for sports areas with a focus on the determination of linear shoe/surface friction.   BS EN 16837 specifies a test method for the determination of shoe/surface friction of synthetic sports surfaces. The method can be used for the assessment of both indoor and outdoor sports surfaces.   Note: This method is not considered suitable for long pile synthetic turf surfaces.  Who is BS EN 16837 - Determination of linear shoe/surface friction for?  

Surfaces for sports areas. Determination of linear shoe/surface friction

T/CSVA 0102-2017 合成材料面层健身步道 要求

1　范围 2　规范性引用文件 3　术语和定义 4　选址要求　 5　建设要求　 6　基础要求　 7　标识要求　 8　辅助设施要求　 9　景观要求　 10　性能要求 11　安全要求　 12　检测与验收　 13　交付　 14　使用说明　

Synthetic Surface Fitness Trail Requirements

ASTM F1162/F1162M-18 撑架着陆系统的标准规范

1.1 This specification covers minimum requirements of size, physical characteristics of materials, standard testing procedures, labeling and identification of pole vault landing systems. 1.2 Units—The values stated in either SI units or inchpound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Pole Vault Landing Systems

ASTM F2949-18 标准规格为撑杆跳箱盒

1.1 This specification covers minimum requirements of size, physical characteristics of materials, standard testing procedures, labeling and identification of pole vault box collars.2 1.2 Units—The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Pole Vault Box Collars

ASTM F2334-18 地面公共使用滑板设施标准指南

1.1 This guide covers safety and performance guidelines pertaining to public skatepark facilities and any element included therein. These guidelines pertain to any elements intended to be used in the performance of the sports including skateboarding, inline skating, and BMX biking. Items such as fencing, lighting, and operational structures are not intended to be a part of this guide. 1.2 This guide applies to above-ground (indoor/outdoor) skatepark elements, intended for recreational use. 1.3 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard. 1.4 Tolerances – General Measures, Tolerances, and Conversions—The general dimensional tolerances for this specification (unless otherwise noted) are as follows: Dimension Tolerance X in. or ft ±0.5 in. or ft X.X in. or ft ±0.05 in. or ft X.XX in. or ft ±0.005 in. or ft NOTE 1—These tolerances still apply to a dimension even when terms like greater than, less than, minimum, or maximum are used. 1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. NOTE 2—The conversion factor from inch-pound to SI units is 1 in. = 25.4 mm, and 1 lb = 0.45359 kg. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Guide for Above Ground Public Use Skatepark Facilities

ASTM F1953-10(2018) 草地网球场建设和维护标准指南

1.1 This guide covers techniques that are appropriate for the construction and maintenance of grass tennis courts. This guide provides guidance for selection of soil systems and turfgrass species in court construction and for selection of management practices that will maintain an acceptable playing surface. 1.2 Decisions in selecting construction and maintenance techniques are influenced by existing soil types, climatic factors, adaptation of grass species, level of play anticipated, intensity of use, budget, equipment, and training and ability of the turf management personnel. 1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Guide for Construction and Maintenance of Grass Tennis Courts

EN 16837:2018 运动区域的表面 线性鞋/表面摩擦的测定

Surfaces for sports areas - Determination of linear shoe/surface friction

ASTM F1346-91(2018) 游泳池 水疗和热水浴缸的所有盖子的安全盖和标签要求的标准性能规范

1.1 This specification establishes requirements for safety covers for swimming pools, spas, hot tubs, and wading pools (hereinafter referred to as pools, unless otherwise specified). When correctly installed and used in accordance with the manufacturer’s instructions, this specification is intended to reduce the risk of drowning by inhibiting the access of children under five years of age to the water. 1.2 This specification includes performance tests to demonstrate the compliance or noncompliance to requirements herein stated for safety covers. It also includes marking requirements for all covers. 1.3 The values stated in inch-pound units are to be regarded as the standard. The values in parentheses are given for information only. 1.4 The following safety hazards caveat pertains only to the test methods section, Section 9, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Performance Specification for Safety Covers and Labeling Requirements for All Covers for Swimming Pools, Spas and Hot Tubs

BS EN 14836:2018 运动区域的表面 用于户外运动区域的合成表面 人工气候老化试验方法

Surfaces for sports areas. Synthetic surfaces for outdoor sports areas. Test method for artificial weathering

ASTM F2007-18 特许卡丁车和设施的分类、设计、制造和操作的标准实施规程

1.1 This practice applies to the design, manufacture, and operation of concession go-karts and their associated operating facilities where public or member use is offered with a use fee. This practice defines classifications for the various vehicles offered for public use to replicate motor sports competitive activities. 1.2 This standard does not apply to vehicles or facilities specifically offered for racing (race karts) or used for general purpose by private owners (fun karts) other than owners of concession go-kart facilities. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Practice for the Classification, Design, Manufacture, and Operation of Concession Go-Karts and Facilities

ASTM F2480-18 地面混凝土滑板标准指南

1.1 This guide covers safety and performance guidelines pertaining to in-ground skatepark facilities built primarily out of concrete and other designed materials. This guide pertains to any concrete materials and other designed materials intended to be used in the performance of the sports including skateboarding, inline skating and BMX biking. Items such as fencing, lighting, and operational structures are not intended to be a part of this guide. 1.2 Tolerance: General Measures, Tolerances, and Conversions—General dimensional tolerances for this guide (unless otherwise noted) follow. These tolerances still apply to a dimension even when terms like greater than, less than, minimum, or maximum are used. Dimension Tolerance X in. or ft ±0.5 in. X.X in. ±0.05 in. X.XX in. ±0.005 in. 1.3 The values stated in inch-pound units are to be regarded as standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Guide for In-ground Concrete Skatepark

T/HSCA 003-2017 学校合成材料面层运动场地建设管理规范

学校合成材料面层的制作和施工管理规范。

Code for construction of synthetic sports surfaces for school

ASTM F1015-03(2017) 人造草皮播放表面相对耐磨性的标准试验方法

Standard Test Method for Relative Abrasiveness of Synthetic Turf Playing Surfaces

ASTM F1551-09(2017) 人造草皮播放表面和材料综合特性的标准试验方法

1.1 These test methods establish a recommended list from which suitable test methods shall be selected for the identification of physical property characteristics and comparison of the performance properties of synthetic turf systems or components for athletic and recreational uses, or both. 1.2 Some of the test procedures are suitable only for the laboratory characterization of either components or the complete system; others are suitable for tests on installed sports fields; and some tests may be applied in both the laboratory and the field. 1.3 The test procedures included in these test methods apply as a group to the description of synthetic turf playing surfaces. 1.4 Some of the test procedures are specific for components of the synthetic turf system, and others apply to the complete synthetic turf playing surface. 1.5 Reference to the methods for testing the synthetic turf playing surface and its components contained herein should state specifically the particular test or tests desired and not necessarily refer to these test methods as a whole. 1.6 This is a physical property characterization standard, and it shall not be construed as a safety standard. 1.7 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.8 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.9 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Methods for Comprehensive Characterization of Synthetic Turf Playing Surfaces and Materials

ASTM F3248-17 测定区域弹性 点弹性 组合弹性和混合弹性体育和舞蹈表面的垂直变形和面积变形的标准试验方法

1.1 This method covers the quantitative measurement and normalization of deflections generated within a sports surface as an indication of the stability and comfort provided by the system. 1.2 Vertical deformation provides a measure for the vertical motion generated within the sports surface system directly below the point of impact which has been normalized to a standard impact force. 1.3 Area deflection provides a measure of the vibrations generated during an impact and their strength at a predetermined distance from the point of impact. 1.4 This method is not applicable to natural turf, synthetic turf or playground safety surfaces. 1.5 This method is applicable to indoor and outdoor surfaces including but not limited to: wood and synthetic courts, walk/jog/run tracks, tennis courts, dance surfaces, aerobics and general fitness surfaces. 1.6 The methods described are applicable in both laboratory and field settings. 1.7 Area deflection testing is optional, and only applicable to area-elastic, combined elastic and mixed elastic sport surfaces. These include wood surfaces, synthetic surfaces on a sprung wood subfloor, and point elastic surfaces with an internal area elastic component. 1.8 The values stated in SI units are to be regarded as standard. Units provided in parenthesis are informational only. 1.9 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.10 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Test Method for Determining Vertical Deformation and Area Deflection of Area Elastic, Point Elastic, Combined Elastic and Mixed Elastic Sport and Dance Surfaces