共找到 261 条与 筛分、筛板与筛网 相关的标准,共 18 页
Technical requirements for heatless regenerative molecular sieve drying and aerating equipment
Sieves and sieving-Industrial wire screens - Number of blemishes
Recommended methods for the subdivision of laboratory powder samples into test portions suitable for analysis by methods for the determination of the particle size distribution described in other Parts of this standard and for particle characterization analysis described in other British Standards.
Methods for determination of particle size distribution - Guide to powder sampling
Sieves and sieving. Terminology.
Describes 4 centrifugal liquid sedimentation methods for the determination of the particle size distribution of powders and suspensions, particularly those with a maximum size of 5 $Gmm.
Methods for determination of particle size distribution - Recommendations for centrifugal liquid sedimentation methods for powders and suspensions
Specifies the code for designating various perforated plate.
Specification for designation of perforations in industrial plate screens
Sieving media; round monofilament yarns, designation, dimensions, requirements, testing
Describes three patterns using round (circular) and square perforations in low carbon steel plate of 3 mm thickness and above. The sizes of holes range from 125 to 3.15 mm inclusive. Five ratios of pitch to hole are prescribed which result in nominal open areas ranging from about 64 to 23 %.
Industrial plate screens; Part 1 : Thickness of 3 mm and above
The perforation of a plate is designated by 1: shape of the holes, 2. aperture size, 3. mutual arrangement of holes, 4. pitch, 5. orientation of the arrangement of the perforations relative to the edges of the plate. The code expresses the items of designation by symbols and magnitudes in the sequence above. The standard applies to perforated plates regardless of the plate material.
Industrial plate screens; Codification for designating perforations
Sieves and sieving. Terminology relating to defects in wire screens.
Tabulates values which are taken from the general list of combinations given in ISO 4783/1. Applies to aperture sizes from 125 to 1 mm. The screens shall de designated in the following sequence by a) width of aperture, b) diameter of wire, c) material of wire, d) type.
Industrial wire screens and woven wire cloth; Guide to the choice of aperture size and wire diameter combinations; Part 3 : Preferred combinations for pre-crimped or pressure-welded wire screens
This method is for determining the size distribution of molecular sieve particles by screening through appropriate U.S.A. Standard Series testing sieves.
Size Distribution of Molecular Sieve Particles
1.1 This specification covers the sizes of round opening perforated plate and screens for general industrial uses, including the separating or grading of materials according to designated nominal particle size, and lists standards for openings from 5 in. (125 mm) to 0.020 in. (500 m) punched with bar sizes and thicknesses of plate for various grades of service. Methods of checking industrial perforated plate and screens are included as information in the Appendix.1.2 This specification does not apply to perforated plate or screens with square, hexagon, slotted, or other shaped openings.1.3 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Standard Specification for Industrial Perforated Plate and Screens (Round Opening Series)
1.1 This specification covers the sizes of square opening perforated plate and screens for general industrial uses, including the separating or grading of materials according to designated nominal particle size, and lists standards for openings from 5 in. (125 mm) to 0.127 ( 1/8 ) in. (3.35 mm) punched with bar sizes and thicknesses of plate for various grades of service. Methods of checking industrial perforated plate and screens are included as information in the Appendix.1.2 This specification does not apply to perforated plate or screens with round, hexagon, slotted, or other shaped openings.1.3 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Standard Specification for Industrial Perforated Plate and Screens (Square Opening Series)
Sieving and granulometry. Determination of the area per unit of mass or volume of powders by permeametry. Lea and nurse method.
Sieve analysis of fine powders with air-jet sieve-apparatus.
Screening surfaces; woven filament clothof silk or man-made fibers; dimensions
Screening surfaces; woven filament cloth of silk or man-made fibers, dimensions
Screening surfaces; woven filament cloth of round man-made monofilaments; dimensionsDie in dieser Norm angegebenen Maschenweiten gelten vorzugsweise für quadratische Maschen. Bei Rechteckmaschen gelten sie für die kleinere Maschenweite. Das Verh?ltnis de
Sceening surfaces; woven filament cloth of round man-made monofilaments, dimensions
Test sieves -- Part 1: Test sieves of metal wire cloth (Erratum 1)
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号