A83 包装方法 标准查询与下载

KS T 1321-2007 造纸原料内填充物及微细纤维的保留度测定方法

1.1 이 방법은 단망 분류기를 이용하여 지료 또는 펄프 표본의 미세물질 함량을 측정하기

Testing method for retention of fines fraction of paper stock

KS T 1322-2007 包装用加工纸的耐黏合性试验方法

이 규격은 포장용 가공지의 내점착성1) 시험 방법에 대하여 규정한다.

Testing method for pressure sensitive adhesive resistance of processed papers for packaging

KS T 1320-2007 阔叶树木纸浆及纸的导管(容器)测定方法

이 규격은 도관의 측정 방법에 대하여 규정한다.

Measuring method for vessels for pulp and paper of hardwood

ASTM D6198-07 运输包装设计的标准指南

This guide assists users in design and development of packaging intended for the protection of goods while they are in transit from point of origin to final destination. By following all steps of this guide, users will be assured that the most important factors are included in package design. In some cases, the sequence of steps may be changed, and often the steps may occur simultaneously with concurrent work activities. The design process focuses on protection from hazards of handling, storage, and shipping while recognizing the economics of all other facets of distribution, including packaging materials and labor, and transportation. In transport packaging, distribution is generally defined as inclusion of handling, storage, and transportation factors.1.1 This guide covers an approach to design of packaging for distributing goods through the hazards of handling, storage, and transportation.1.2 The principal content of this guide is the identification of the key steps involved in development of transport packages, including shipping containers, interior protective packaging, and unit loads. It is recognized that actual usage and application to individual design projects may vary appreciably without diminishing the value of the process. Consult with a packaging professional whenever needed.1.3 This guide is not intended for design of primary packaging unless the primary package is planned for use as a shipping container.1.4 The user of this guide must be aware of the carrier rules regarding packaging for shipment via each mode of transportation in which the transport package may move, such as the National Motor Freight Classification (less-than truckload) and the Uniform Freight Classification (railroad). For hazardous materials packaging, the packaging must perform to the requirements of the applicable modal regulations listed in Section 2.1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Guide for Transport Packaging Design

ASTM D3475-07 防止儿童开启的包装的标准分类

1.1 This classification covers various types of child-resistant packages.1.2 The examples for each type of child-resistant packaging are not intended to be all-inclusive, but are included only as an aid in the understanding and comprehension of each type of classification.1.3 Listings are not to be considered endorsements or approval of the package by ASTM.

Standard Classification of Child-Resistant Packages

KS T 1323-2006 圆柱型运输容器的降落试验方法

이 규격은 금속이나 판지 또는 나무로 만든 원통형 수송 용기의 낙하 시험 방법에 대하여

Drop test for cylindrical shipping containers

KS T 0204-2006 瓦楞纸板的静态弯曲试验方法

이 규격은 양면 또는 이중 양면 골판지의 정적 만곡 시험 방법에 대하여 규정한다.

Static bending test for corrugated paperboard

KS T 1310-2006 包装货物及容器的倾斜冲击试验方法

이 규격은 운송용 포장 또는 단위 적재 화물의 수평 충격 시험 방법(수평면 또는 경사면 시

Method of incline impact test for packages and shipping containers

KS T 1307-2006 大牛皮纸袋降落试验方法

이 규격은 내용물을 채운 크라프트 지대(이하 지대라 한다.)의 낙하 시험 방법에 대하여 규

Method of drop test for kraft paper sacks

KS T ISO 16101:2006 包装.危险货物的运输包装.塑料兼容性试验

이 규격은 플라스틱 포장 용기 및 액체를 포함하는 내부 플라스틱 용기로 구성된 포장물에 있

Packaging-Transport packaging for dangerous goods-Plastic compatibility testing

KS T ISO 11897:2006 包装.热塑柔性薄膜袋.折边处的撕裂扩展试验

이 규격은 주어진 조건하에서, 열가소성 플라스틱 필름으로 만든 대의 가장자리 접힘부에서의

Packaging-Sacks made from thermoplastic flexible film-Tear propagation on edge folds

KS T 1312-2006 包装胶带黏着力试验方法

이 규격은 종이 검 테이프 및 천 검 테이프 등의 초기 점착성과 접착력 시험 방법에 대하

Testing method for adhesive strength of gummed tape

KS T 1325-2006 卡纸的渗水试验方法

이 규격은 강 사이징한 판지의 침수 시험 방법에 대하여 규정한다.

Water immersion testing method of paperboard

DIN ISO 11648-1:2006 散料取样的统计方法.第1部分:一般原理(ISO 11648-1-2003)

The standard deals with general statistical principles of sampling of bulk materials. This means methods such as design of sampling methods and determining precision and trueness.

Statistical aspects of sampling from bulk materials - Part 1: General principles (ISO 11648-1:2003)

JIS X 0516:2006 包装.产品包装用线形条码和二维符号

この規格は，次に示す仕様について規定する。

Packaging -- Linear bar code and two-dimensional symbols for product packaging

ISO 16106:2006 包装.危险货品运输包装.危险货物包装、中间散货容器(IBCs)和大型包装.应用ISO 9001的指南

This International Standard gives guidance on quality management provisions applicable to the manufacture, measuring and monitoring of design type approved dangerous goods packagings, intermediate bulk containers (IBCs) and large packagings. This International Standard can only be used in combination with ISO 9001:2000 and is not a stand-alone document. It does not apply to design type testing, for which reference is made to 6.1.5, 6.5.4 and 6.6.5 of the UN Model Regulations Ml.

Packaging - Transport packages for dangerous goods - Dangerous goods packagings, intermediate bulk containers (IBCs) and large packagings - Guidelines for the application of ISO 9001

BS EN ISO 16103:2006 包装.危险物品运输包装.再生塑料材料

ISO 16103:2005 specifies the requirements and test methods for the production of recycled plastics materials to be used for packagings for the transport of dangerous goods. This includes guidance on the quality assurance programme.

Packaging - Transport packages for dangerous goods - Recycled plastics material

BS EN 14887:2005 玻璃包装.开启软木塞工具.一般要求

This European Standard gives general requirements for the design of all types of cork removal devices.

Glass packaging — Cork removal devices — General requirements

DIN EN 862:2006 包装.防止儿童打开的包装.非药物用不可再封闭的包装要求和试验过程.德文版本EN 862-2005

This European Standard specifies performance requirements and methods of test for non-reclosable packaging that has been designated child-resistant and which is intended to contain non- pharmaceutical products. This standard is intended for type approval only (2.5) and is not intended for quality assurance purposes. This European Standard applies to non-reclosable packages of the single-use type consisting of one or more individual units. Non-reclosable packages for pharmaceutical products are excluded from the scope of this standard. These are the subject of a separate standard, EN 14375 Child-resistant non-reclosable packaging for pharmaceutical products - Requirements and testing.

Packaging - Child-resistant packaging - Requirements and testing procedures for non-reclosable packages for non-pharmaceutical products; English version of DIN EN 862:2006-02

ASTM D3481-06 将防止儿童开启的两个同时反向运动的关闭器的手动两部分分开所需力的试验方法

This test method of applying force may be used as a standard test to compare the characteristics of a given design of container/child-resistant closure system with a standard or to compare the characteristics of container/child-resistant closure systems differing in construction. It may be used to simulate certain manipulations that may be expected to occur in protocol testing4 (such as, prying with the teeth or objects in the room, biting, and pulling with the teeth). This test method may be used to establish performance specifications. 1.1 This test method covers the measurement of the force required to separate (or "shell") the snap-fitted outer cap from the inner cap of Type IA, IB, or IC child-resistant closures.1.2 This test method does not measure the force required to separate parts of a child-resistant closure system that were originally "screwed-on" instead of "snapped-on" (for example, pull a cap over or through continuous or multi-start threads when the cap was originally screwed on).1.3 The values stated in SI units are to be regarded as the standard. The inch-pound units given in parentheses are for information only.This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Manual Shelling Two-Piece Child-Resistant Closures That Are Activated by Two Simultaneous Dissimilar Motions