B69 木材加工材 标准查询与下载
共找到 776 条与 木材加工材 相关的标准，共 52 页
5.1 Solid board, lumber and timber products (including solid boards, lumber, timber, fingerjoined lumber, glulam, laminate wood, laminated veneer lumber and parallel strand lumber products); panel products (including fibreboard, hardboard, oriented strandboard, waferboard and plywood panel products); decorative wood products and shingles and shakes used as interior wall and ceiling finish are often evaluated with Test Method E84 to comply with code requirements. This practice describes specimen preparation and mounting procedures for such materials and systems. 5.2 If it can be demonstrated that none of the methods described in this practice are applicable to a particular product, other mounting methods shall be permitted to be used. This information shall be included in the report. 5.3 The limitations for this procedure are those associated with Test Method E84. 1.1 This practice describes procedures for specimen preparation and mounting when testing wood products to assess flames spread and smoke development as surface burning characteristics using Test Method E84. 1.2 This practice applies also to laminated products factory-produced with a wood substrate (see 8.6). This practice does not apply to wood veneers or facings intended to be applied on site over a wood substrate, which are covered by Practice E2404. 1.3 Testing is conducted with Test Method E84. 1.4 This practice does not provide pass/fail criteria that can be used as a regulatory tool. 1.5 Use the values stated in inch-pound units as the standard, in referee decisions. The values in the SI system of units are given in parentheses, for information only; see IEEE/ASTM8201;SI-10 for further details. 1.6 This fire standard cannot be used to provide quantitative measures. 1.7 Fire testing of products and materials is inherently hazardous, and adequate safeguards for personnel and property shall be employed in conducting these tests. Fire testing involves hazardous materials and equipment. This standard gives instructions on specimen preparation and mounting, but the fire-test-response method is given in Test Method E84. See also Section 10. 1.8 The text of this standard references note......
Standard Practice for Specimen Preparation and Mounting of Wood Products to Assess Surface Burning Characteristics
- ICS
- 13.220.40 (Ignitability and burning behaviour of m
- CCS
- B69
- 发布
- 2013
- 实施
Practice for Specimen Preparation and Mounting of Wood Products to Assess Surface Burning Characteristics
- ICS
- 13.220.40;79.080
- CCS
- B69
- 发布
- 2013
- 实施
Wood－Determination of density for physical and mechanical tests
- ICS
- 79.040
- CCS
- B69
- 发布
- 2012-12-22
- 实施
本标准规定了木材及木制品中alpha-六六六、beta-六六六、gamma-六六六、delta-六六六、七氯、艾氏剂、氯丹、狄氏剂、2,4'-滴滴涕、4,4'-滴滴涕10 种有机氯杀虫剂的气相色谱测定方法。本标准适用于木材及木制品中有机氯杀虫剂的测定。
Determination of organochlorine pesticides in timber and wood products.Gas chromatography method
- ICS
- CCS
- B69
- 发布
- 2012-12-12
- 实施
- 2013-07-01
Cork - Cork stoppers for still wine - Sampling plan for the quality control of cork stoppers
- ICS
- 55.100;79.100
- CCS
- B69
- 发布
- 2012-12
- 实施
Durability of wood and wood-based products - Determination of emissions from preservative treated wood to the environment - Part 2: Wooden commodities exposed in Use Class 4 or 5 (in contact with the ground, fresh water or sea water) - Laboratory method;
- ICS
- 13.020.30;71.100.50
- CCS
- B69
- 发布
- 2012-12
- 实施
Durability of wood and wood-based products - Criteria for hot air processes for curative uses against wood destroying organisms; German version CEN/TR 15003:2012
- ICS
- 79.040
- CCS
- B69
- 发布
- 2012-11
- 实施
이 표준은 콘크리트 슬래브 위에 시공되는 바닥 마감 구조의 경량 충격음 레벨 저감량을 실험
Laboratory measurements of the reduction of transmitted impact sound by floor coverings on a heavyweight standard floor
- ICS
- 91.120.20
- CCS
- B69
- 发布
- 2012-09-13
- 实施
- 2012-09-13
Structural Timber. Strength classes. Assignment of visual grades and species
- ICS
- 79.040
- CCS
- B69
- 发布
- 2012-08-31
- 实施
- 2012-08-31
本标准规定了红木制品的等级、等级划分、等级评定的方法以及包装、运输、贮存、标识的要求。本标准适用于红木制品。
Specification for classification of Hongmu products
- ICS
- 79.020
- CCS
- B69
- 发布
- 2012-08-01
- 实施
- 2012-11-01
This International Standard delineates and illustrates broad grade categories that specify essential features typically found in those categories based on commonalities of numerous national standards and grading rules used for non-structural timber of non-coniferous and coniferous species in international commerce. It provides a basis for recognition of a national standard or grading rules that comply with this International Standard and is applicable to all methods of visual grading systems for non-structural timber of all non-coniferous and coniferous species of timber. Non-structural timber produced from bamboo is not covered in this International Standard.
Non-structural timber grading requirements
- ICS
- 79.040
- CCS
- B69
- 发布
- 2012-08
- 实施
Structural timber - Strength classes - Assignment of visual grades and species; German version EN 1912:2012
- ICS
- 79.040
- CCS
- B69
- 发布
- 2012-06-01
- 实施
Strength grading of wood - Part 1: Coniferous sawn timber
- ICS
- 79.040
- CCS
- B69
- 发布
- 2012-06-01
- 实施
Specification for the requirements and test methods for processing waste wood
- ICS
- 13.030.50;79.020
- CCS
- B69
- 发布
- 2012-04-02
- 实施
- 2012-04-02
Timber structures. Strength graded structural timber with rectangular cross section. Machine grading; additional requirements for factory production control
- ICS
- 79.040
- CCS
- B69
- 发布
- 2012-03-31
- 实施
- 2012-03-31
Wood. Sampling methods and general requirements for physical and mechanical testing of small clear wood specimens
- ICS
- 79.040
- CCS
- B69
- 发布
- 2012-02-29
- 实施
- 2012-02-29
Square timber for interior decoration
- ICS
- 79.040
- CCS
- B69
- 发布
- 2012-02-23
- 实施
- 2012-07-01
