B69 木材加工材 标准查询与下载
共找到 776 条与 木材加工材 相关的标准，共 52 页
Structural wood material terminology
- ICS
- 79.060
- CCS
- B69
- 发布
- 2018-12-29
- 实施
- 2019-05-01
Test methods for artificial aging of wood coatings for outdoor use
- ICS
- 79.040
- CCS
- B69
- 发布
- 2018-12-29
- 实施
- 2019-05-01
Granulated cork and cork powder. Classification, properties and packing
- ICS
- 79.100
- CCS
- B69
- 发布
- 2018-10-24
- 实施
- 2018-10-24
Round and sawn timber. Methods of measurements. Features and biological degradations
- ICS
- 79.040
- CCS
- B69
- 发布
- 2018-05-18
- 实施
- 2018-05-18
本标准规定了利用生长锥取样测定木材密度的设备、方法和测定结果与报告等要求。 本标准适用于木材密度的测定。
Method for Determining Density of Wood from Growth Cone Sampling
- ICS
- 79.040
- CCS
- B69
- 发布
- 2018-03-28
- 实施
- 2018-06-28
This European Standard specifies the methodology for measurement of features - in relation to wood structure, biological agencies and other damage - taken into account in the visual grading: a) for appearance - of sawn, processed and round timber; b) for serviceability - of sawn and processed timber (identified in EN 1611-1 as the integrity of the timber). When the standard is applied the methodology of measurement used shall be stated. It is not applicable to structural timber for which strength grading in accordance with EN 14081-1 is required. This standard applies to hardwood and softwood sawn timber, both square edged and un-edged, to processed timber and to round timber. It does not apply to tropical timber.
Round and sawn timber - Methods of measurements - Part 3: Features and biological degradations; German version EN 1309-3:2018
- ICS
- 79.040
- CCS
- B69
- 发布
- 2018-03-01
- 实施
本标准规定了木杆树种、尺寸、材质指标、检验方法及材积计算等。 本标准适用于全国木材生产、流通领域的农具、工具、棚架、木制构件及矿扒条用料等。
Wood pole
- ICS
- 79.040
- CCS
- B69
- 发布
- 2018-02-27
- 实施
- 0000-00-00
This European Standard defines a method of assessment of drying quality. It applies to a lot of dried sawn timber (surfaced or not). It applies to both softwood and hardwood with a thickness not greater than 100 mm. The quality of drying is expressed in terms of target and average moisture content of the lot as well as defining the moisture content variation between individual pieces expressed as allowable upper and lower limits. An option for specifying the degree of case-hardening is included. NOTE 1 Other features related to drying, e. g. checking, distortions, stain, etc., are specified in documents for visual grading of sawn timber or in product specifications and are not covered by this document. NOTE 2 In the following the term sawn timber is used for all dried timber covered by this the scope.
Sawn timber - Assessment of drying quality; German version EN 14298:2017
- ICS
- 79.040
- CCS
- B69
- 发布
- 2018-01-01
- 实施
This European Standard defines terms and specifies requirements and test methods for wood veneer floor coverings with multilayer built up for internal use. It gives guidance for the evaluation of conformity of the products to the requirements of this standard. This European Standard is not applicable to multilayer parquet elements with a minimum top layer thickness of 2,5 mm. For these products EN 13489 applies.
Wood-based panels - Wood veneer floor coverings; German version EN 14354:2017
- ICS
- 79.080
- CCS
- B69
- 发布
- 2017-11-00
- 实施
This document specifies a method for the determination of the resistance of wood to impact indentation by a steel ball.
Physical and mechanical properties of wood - Test methods for small clear wood specimens - Part 11: Determination of resistance to impact indentation
- ICS
- 79.040
- CCS
- B69
- 发布
- 2017-10-01
- 实施
This document specifies a method for determining of the static hardness of wood by measuring resistance of a test piece to the penetration of a plunger under gradually increasing load.
Physical and mechanical properties of wood - Test methods for small clear wood specimens - Part 12: Determination of static hardness
- ICS
- 79.040
- CCS
- B69
- 发布
- 2017-10-01
- 实施
This document specifies a method for determining the impact bending strength of wood.
Physical and mechanical properties of wood - Test methods for small clear wood specimens - Part 10: Determination of impact bending strength
- ICS
- 79.040
- CCS
- B69
- 发布
- 2017-10-00
- 实施
This document specifies test methods to determine the characteristics of agglomerated composition cork and rubbercork to be used as gaskets in the mechanical industry. The following characteristics are considered: — thickness, — apparent density, — tensile strength, — compressibility and recovery, — flexibility, — resistance to boiling water, — behaviour in fluids.
Composition cork - Gasket material - Test methods
- ICS
- 21.140;79.100
- CCS
- B69
- 发布
- 2017-09-00
- 实施
Determination of phoxim pesticide in wood and its products by liquid chromatography-mass spectrometry
- ICS
- 79.020
- CCS
- B69
- 发布
- 2017-05-12
- 实施
- 2017-12-01
