D10 地质矿产勘察与开发综合 标准查询与下载

MT/T 1043-2007 遥感煤田地质填图技术规程

本标准规定了遥感煤田地质填图（1:50000、1:25000、1:10000、1:5000）的目的、工作程度、工作方法及精度要求，并规定了设计编制、原始编录、资料整理、成图方法、填图报告编制、检查验收 等要求。 本标准适用于不同类型地质可解译程度地区的煤田地质勘查阶段（1:50000、1:25000、1:10000、1:5000）使用航天、航空遥感技术进行的煤田地质填图。 本标准可作为煤田地质填图以外的其他遥感地质填图参考性技术标准。

Technological regulations of remote sensing mapping for coalfield geology

DIN 21901 Bb.1:2006 矿山测量平面图.标准的结构和标准一览表.补充件1:内容

Mine plans - Structure and list of standards - Supplement 1: Contents

DIN 21901 Bb.2:2006 矿山测量平面图.标准的结构和标准一览表.补充件2:缩略语索引

Mine plans - Structure and list of standards - Supplement 2: List of abbreviations

DZ/T 0220-2006 泥石流灾害防治工程勘查规范

本规范规定了泥石流类型划分及危害性分级、泥石流灾害的调查与勘查等内容。 本规范规定了自然或人为因素引发的危及城镇人口集中区、大中型工矿企业、风景名胜区等公共安全的泥石流灾害勘查工作；也可适用于危及水利水电、公路、铁路等基础设施安全的泥石流灾害勘查工作。

Specification of geological investigation for debris flow stabilization

DZ/T 0221-2006 崩塌、滑坡、泥石流监测规范

本规范规定了滑坡、崩塌变形与泥石流活动的监测内容、监测方法、监测点网布设、监测资源整理，以及变形破坏或活动预报等技术要求。 本规范适用于已经发生过且随可能继续或再次发生变形破坏和活动的滑坡、崩塌与泥石流的监测，以及有可能发生崩滑的自然或人为的斜坡和泥石流活动的沟槽（或斜坡）的监测。 本规范以专业监测为主，部分内容可供群测群防监测参见。

Monitoring code of rockfall,landslide and debris flow

DZ/T 0218-2006 滑坡防治工程勘查规范

本规范规定了滑坡与崩塌分类及危害分级、可行性论证阶段、设计阶段、施工阶段勘查以及应急治理的勘查要求，并规定了主要勘查方法、物理力学试验与稳定状态分析、竣工地质报告等内容。 本规范适用于自然滑坡防治工程的勘查，也可用于水利水电、铁道、交通、城建、矿山等行业的滑坡防治工程勘查。 本规范中除特别注明外，可适用于崩塌防治工程勘查。

Specification of geological investigation for landslide stabilization

DZ/T 0219-2006 滑坡防治工程设计与施工技术规范

本规范规定了滑坡防治工程设计基本规定、滑坡分类及防治工程勘察、滑坡防治工程分级及设计安全系数、排水工程、抗滑桩、预应力锚索、格构锚固、重力挡墙、注浆加固、刷方减载、回填压脚、植物预防、滑坡防治监测、施工组织、质量检验及工程验收等内容。 本规范适用于指导滑坡防治工程设计。

Specification of design and construction for landslide stabilization

DIN 21912-1:2006 矿山平面图.露天矿山.第1部分:一般要求

This standard applies to the features of mining-specific mapping. The standard contains symbols, abbreviations and terms to be used for the representation of open cast mines in mining specific mapping.#,,#

Mine plans - Opencast mining - Part 1: General requirements

ASTM D2113-06 现场勘测用岩芯钻探和取样的标准操作规程

Rock cores are samples of record of the existing subsurface conditions at given borehole locations. The samples are expected to yield significant indications about the geological, physical, and engineering nature of the subsurface for use in the design and construction of an engineered structure (see Guide D 420 . The core samples need to be preserved using specific procedures for a stipulated time (Practices D 5079). The period of storage depends upon the nature and significance of the engineered structure. Rock cores always need to be handled such that their properties are not altered in any way due to mechanical damage or changes in ambient conditions of moisture and temperature or other environmental factors. 1.1 This practice covers the guidelines, requirements, and procedures for core drilling, coring, and sampling of rock for the purposes of site investigation. The borehole could be vertical, horizontal, or angled.1.2 This practice is described in the context of obtaining data for the design, construction, or maintenance of structures, and applies to surface drilling and drilling from adits and exploratory tunnels.1.3 This practice applies to core drilling in hard and soft rock.1.4 This practice does not address considerations for core drilling for geo-environmental site characterization and installation of water quality monitoring devices (see Guides D 5782 and D 5783).1.5 The values stated in inch-pound units are to be regarded as standard. The SI values given in parentheses are provided for information purposes only.1.6 This practice does not purport to comprehensively address all of the methods and the issues associated with coring and sampling of rock. Users should seek qualified professionals for decisions as to the proper equipment and methods that would be most successful for their site investigation. Other methods may be available for drilling and sampling of rock, and qualified professionals should have flexibility to exercise judgment as to possible alternatives not covered in this practice. This practice is current at the time of issue, but new alternative methods may become available prior to revisions; therefore, users should consult with manufacturers or producers prior to specifying program requirements.This practice offers a set of instructions for performing one or more specific operations. This document cannot replace education or experience and should be used in conjunction with professional judgment. Not all aspects of this practice may be applicable in all circumstances. This ASTM standard is not intended to represent or replace the standard of care by which the adequacy of a given professional service must be judged, nor should this document be applied without consideration of a project''s many unique aspects. The word "Standard" in the title of this document means only that the document has been approved through the ASTM consensus process.This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Also, the user must comply with prevalent regulatory codes, such as OSHA (Occupational Health and Safety Administration) guidelines, while using this practice. For good safety practice, consult applicable OSHA regulations and other safety guides on drilling ().

Standard Practice for Rock Core Drilling and Sampling of Rock for Site Investigation

DIN 21914-1:2005 矿区平面图.钻探和孔洞.第1部分:钻探

This standard applies to the features of mining-specific mapping. The document contains the required terms, symbols, and abbreviations to be used for marking boreholes in mining-specific maps and plans for opencast mining and deep mining. The standard applies to all mining branches.

Mine plans - Drilling and cavern - Part 1: Drilling

AQ 2004-2005 地质勘探安全规程

本标准规定了地质勘探工作野外作业、地质测绘、地球物理勘探、地球化学勘探、地质遥感、水文地质、环境地质、工程地质、海洋地质和钻探工程、坑探工程、地质实验测试等方面的安全要求以及职业健康要求。 本标准适用于在中华人民共和国领域内的地质勘探(石油、天然气地质勘探除外)工作设计、生产和安全评价、管理。 本标准不适用于使用地质勘探技术手段和方法从事其延伸业的工作设计、生产和安全评价、管理。

Safety regulations for geological prospecting operation

ASTM D5753-05(2010) 地球物理测井管道钻孔的标准指南

An appropriately developed, documented, and executed guide is essential for the proper collection and application of borehole geophysical logs. The benefits of its use include improving the following: Selection of logging methods and equipment, Log quality and reliability, and Usefulness of the log data for subsequent display and interpretation. This guide applies to commonly used logging methods (see Table 1 and Table 2) for geotechnical investigations. It is essential that personnel (see 7.3.3) consult up-to-date textbooks and reports on each of the logging techniques, applications, and interpretation methods. A partial list of selected publications is given at the end of this guide. This guide is not meant to describe the specific or standard procedures for running each type of geophysical log and is limited to measurements in a single borehole.1.1 This guide covers the documentation and general procedures necessary to plan and conduct a geophysical log program as commonly applied to geologic, engineering, ground-water, and environmental (hereafter referred to as geotechnical) investigations. It is not intended to describe the specific or standard procedures for running each type of geophysical log and is limited to measurements in a single borehole. It is anticipated that standard guides will be developed for specific methods subsequent to this guide. 1.2 Surface or shallow-depth nuclear gages for measuring water content or soil density (that is, those typically thought of as construction quality assurance devices), measurements while drilling (MWD), cone penetrometer tests, and logging for petroleum or minerals are excluded. 1.3 Borehole geophysical techniques yield direct and indirect measurements with depth of the (1) physical and chemical properties of the rock matrix and fluid around the borehole, (2) fluid contained in the borehole, and (3) construction of the borehole.

Standard Guide for Planning and Conducting Borehole Geophysical Logging

ASTM D5753-05 地球物理测井的钻孔计划和实施的标准指南

An appropriately developed, documented, and executed guide is essential for the proper collection and application of borehole geophysical logs. 5.1.1 The benefits of its use include improving the following: 5.1.1.1 Selection of logging methods and equipment, 5.1.1.2 Log quality and reliability, and 5.1.1.3 Usefulness of the log data for subsequent display and interpretation. 5.1.2 This guide applies to commonly used logging methods (see Table 1 and Table 2) for geotechnical investigations. 5.1.3 It is essential that personnel (see 7.3.3) consult up-to-date textbooks and reports on each of the logging techniques, applications, and interpretation methods. A partial list of selected publications is given at the end of this guide. 5.1.4 This guide is not meant to describe the specific or standard procedures for running each type of geophysical log and is limited to measurements in a single borehole.1.1 This guide covers the documentation and general procedures necessary to plan and conduct a geophysical log program as commonly applied to geologic, engineering, ground-water, and environmental (hereafter referred to as geotechnical) investigations. It is not intended to describe the specific or standard procedures for running each type of geophysical log and is limited to measurements in a single borehole. It is anticipated that standard guides will be developed for specific methods subsequent to this guide.1.2 Surface or shallow-depth nuclear gages for measuring water content or soil density (that is, those typically thought of as construction quality assurance devices), measurements while drilling (MWD), cone penetrometer tests, and logging for petroleum or minerals are excluded.1.3 Borehole geophysical techniques yield direct and indirect measurements with depth of the (1) physical and chemical properties of the rock matrix and fluid around the borehole, (2) fluid contained in the borehole, and ( 3) construction of the borehole.1.4 To obtain detailed information on operating methods, publications (for example, , , , , , , , , and ) should be consulted. A limited amount of tutorial information is provided, but other publications listed herein, including a glossary of terms and general texts on the subject, should be consulted for more complete background information.1.5 This guide provides an overview of the following: (1) the uses of single borehole geophysical methods, (2) general logging procedures, ( 3) documentation, (4) calibration, and (5) factors that can affect the quality of borehole geophysical logs and their subsequent interpretation. Log interpretation is very important, but specific methods are too diverse to be described in this guide.1.6 Logging procedures must be adapted to meet the needs of a wide range of applications and stated in general terms so that flexibility or innovation are not suppressed.1.7 This standard does not purport to address all of the safety and liability concerns, if any, (for example, lost or lodged probes and radioactive sources ) associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 1.8 This guide offers an organized collection of information or a series of options and does not recommend a specific course of action. This document cannot replace education or experience and should be used in conjunction with professional judgment. Not all aspects of this guide may be applicable in all circumstances. This ASTM standard is not intended to represent or replace......

Standard Guide for Planning and Conducting Borehole Geophysical Logging

DIN 21918-2:2004 矿山测量平面图.矿床.第2部分:厚度

Mine plans - Mineral deposits - Part 2: Thicknesses

SY/T 6600-2004 承荷探测电缆

本标准规定了承荷探测电缆的型号、规格、技术要求、试验方法、检验规则、包装标志和使用导则。 本标准适用于各类油、气井的测井、射孔、取心及油井的清蜡、降粘、降凝等承受机械负荷的钢丝铠装油矿探测电缆。

load detection cable

DIN 21913-6:2004 矿山测量平面图.地下采矿.第6部分:矿坑的妥善保护

This standard applies to the representation of safekeeping measures in mine plans.

Mine plans - Deep mining - Part 6: Safekeeping of mining produced hollows

DIN 21907:2003 矿山设计图.布置图图形设计

The document applies to the features of mining-specific mapping. The standard contains symbols, abbreviations, and terms to be used for mining specific maps, plans, and drawings.

Mine plans - Graphic design of sheets

DZ/T 0203-2002 稀有金属矿产地质勘查规范

Specifications for Geological Exploration of Rare Metal Minerals

DIN 21901 Bb.3:2002 矿山平面图.标准结构和目录.索引

Mine plans - Structure and list of standards - Index

DIN 21917-2:2002 矿山勘测平面图.地层和地面运动.第2部分:地球力学测量点

The document applies to the features of mining-specific mapping. It contains symbols, abbreviations, and terms to be used for the representation of geomechanical measuring points in mining-specific mapping.

Mine plans - Strata and ground movements - Part 2: Geomechanical measuring points