D90 矿山机械设备综合 标准查询与下载

MT/T 1003.3-2006 滚筒采煤机.大修规范.第3部分：电气部分

MT/T 1003的本部分规定了滚筒采煤机电气部分大修的一般原则，大修后电动机、电控装置及电气调速装置的要求和试验。 本部分适用于需要大修的滚筒采煤机电气部分。

Shearer-Specification of overhaul.Part 3:Electrical part

MT/T 621-2006 矿井生产检查煤样采取方法

本标准规定了井矿生产检查煤样的采取方法。 本标准适用于各矿井综采、机采和炮采回采工作面、掘进工作面生产检查煤样的采取。

Sampling for checking samples of production in coalmine

MT/T 83-2006 滚筒采煤机　产品型号编制方法

本标准规定了滚筒采煤机（以下简称采煤机）产品型号的组成和排列、产品型号各组成代号的说明和产品型号编制示例。 本标准适用于采煤机产品型号的编制。

Drum shearer--Method of type symbolization

ASTM D7242-06 用直推式地下水取样器测定蓄水层液压特性的现场气动排料孔(水头瞬息变化)试验的标准实施规范

1.1 This standard practice covers the field methods used to conduct an instantaneous change in head (slug) test when pneumatic pressure is used to initiate the change in head pressure within the well or piezometer. While this practice specifically addresses use of pneumatic initiation of slug tests with direct push tools these procedures may be applied to wells or piezometers installed with rotary drilling methods when appropriate.1.2 This standard practice is used to obtain the required field data for determining hydraulic properties of an aquifer or a specified vertical interval of an aquifer. Field data obtained from application of this practice are modeled with appropriate analytical procedures (Test Methods D 4104, D 5785, D 5881, D 5912, Ref (1)).1.3 UnitsThe values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.1.5 This practice offers a set of instructions for performing one or more specific operations. This document cannot replace education or experience and should be used in conjunction with professional judgment. Not all aspects of this practice may be applicable in all circumstances. This ASTM standard is not intended to represent or replace the standard of care by which the adequacy of a given professional service must be judged, nor should this document be applied without consideration of a projects many unique aspects. The word "standard" in the title means that the document has been approved through the ASTM consensus process.

Standard Practice for Field Pneumatic Slug (Instantaneous Change in Head) Tests to Determine Hydraulic Properties of Aquifers with Direct Push Ground Water Samplers

KS E 4090-2005 便携式瓦斯探测器

이 규격은 석탄 광산 등에서 메탄의 농도를 측정하는 휴대용 메탄 가스 검정기(이하 검정기라

Portable type methane gas detector

KS E 4088-2004 矿山用简易救生设备

이 규격은 탄광 및 광산의 갱내 등에 있어서 화재, 폭발, 가스 돌출, 기타의 사고에

Escape breathing apparatus for miners

KS E 6007-2004 矿车及配件

이 규격은 광산에서 사용하는 강제 광차의 차체, 차륜, 차축, 축수금 및 연결기에 대하

Mine steel tub and parts

ASTM E2278-04 露天矿土壤改良用煤燃烧产物使用的标准指南:酸性矿排水区域的再植被和调节

1.1 This guide covers the beneficial use of coal combustion products (CCPs) for abatement of acid mine drainage and revegetation for surface mine reclamation applications related to area mining, contour mining, and mountaintop removal mining. It does not apply to underground mine reclamation applications. There are many important differences in physical and chemical characteristics that exist among the various types of CCPs available for use in mine reclamation. CCPs proposed for each project must be investigated thoroughly to design CCP placement activities to meet the project objectives. This guide provides procedures for consideration of engineering, economic, and environmental factors in the development of such applications.1.2 The utilization of CCPs under this guide is a component of a pollution prevention program; Guide E 1609 describes pollution prevention activities in more detail. Utilization of CCPs in this manner conserves land, natural resources, and energy.1.3 This guide applies to CCPs produced primarily from the combustion of coal.1.4 The testing, engineering, and construction practices for using CCPs in mine reclamation are similar to generally accepted practices for using other materials, including cement and soils, in mine reclamation.1.5 Regulations governing the use of CCPs vary by state. The user of this guide has the responsibility to determine and comply with applicable regulations.1.6 The values stated in inch-pound units are to be regarded as the standard. The SI units given in parentheses are for information only.1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory requirements prior to use.

Standard Guide for Use of Coal Combustion Products (CCPs) for Surface Mine Reclamation: Revegetation and Mitigation of Acid Mine Drainage

KS E ISO 7194-1:2003 封闭管道内液体流量测量.第1部分:利用流速计或皮托静压管对圆形管道中不均匀成旋涡状态流量测量的速度.面积法

이 규격은 유동기나 피토 정지관을 이용하여, 원형 도관에서 소용돌이 또는 비대칭 흐름

Measurement of fluid flow in closed conduits􀫥 Velocity-area methods of flow measurement in swirling or asymmetric flow conditions in circular ducts by means of current-meters or Pitot static tubes

JIS M 0103:2003 钻探设备和工具术语汇编

この規格は，鉱業，建設業などで行う一般地質調査，グラウト孔のせん孔，さく井などに使用する回転式ポーリング用機械・器具の用語(以下，用語という。)について規定する。

Glossary of terms for drilling equipments and tools

DIN 21500:2001 采矿掘井.设计和尺寸规定

The document applies to the design and dimensioning of load-bearing support structures for new mine shafts which are generally circular in profile and cylindrical in shape and which are to be sunk vertically in competent and non-competent strata. It also applies to existing which are to be reconstructed, reinforced or repaired and which for this purpose have to be provided with preliminary support structures or new shaft linings and fittings.#,,#

Shaft sinking in mining - Design and dimensioning

JB/T 10243-2001 KPTH型减速器

JB/T 10243—2001 本标准规定了KPTH渐开线圆柱齿轮减速器的型式，外型尺寸，基本参数，技术要求，试验方法，检验规则，标志、包装、运输和贮存。 本标准适用于KPTH渐开线圆柱齿轮减速器。该减速器主要用于矿井提升机，也可用于冶金、水泥、化工、建材、能源及轻工等行业机械设备的传动中。 本标准于2001年5月首次发布。

KPTH type reducers

JB/T 10244-2001 JPT型减速器

JB/T 10244—2001 本标准规定了JPT渐开线圆柱齿轮减速器的型式，外型尺寸，基本参数，技术要求，试验方法，检验规则，标志、包装、运输和贮存。 本标准适用于JPT渐开线圆柱齿轮减速器。该减速器主要用于建材行业，也可用于矿山、冶金、化工及轻工等行业机械设备的传动中。 本标准于2001年5月首次发布。

JPT type reducer

MT/T 257-2000 煤矿水中游离二氧化碳的测定方法

本标准规定了用碱滴定法测定煤矿水中的游离二氧化碳。 本标准适用于煤矿水中游离二氧化碳的侧定。在本标准规定条件下，测定游离二氧化碳范围为0.1~50 mg/L。 本标准不适用于溶解性固体浓度大于1000mg/L或总硬度(以CaCO2计)大于500mg/L以及含除碳酸外的其他酸的水样中游离二氧化碳的测定。

Determination method of free carbon dioxide in coal mine water

MT/T 256-2000 煤矿水中pH值的测定方法

本标准规定用电位法和指示剂比色法侧定煤矿水的pH值。电位法作为仲裁法。 本标准适用于煤矿水pH值的测定。在本标准规定条件下，pH值的测定范围是0~14。

Measuring method of pH value in coal mine water

MT/T 255-2000 煤矿水中可溶性二氧化硅的测定方法

本标准规定了用钥酸盐比色法测定煤矿水中的可溶性二氧化硅。 本标准适用于煤矿水中可溶性二氧化硅的测定。在本标准规定条件下，测定可溶性二氧化硅的溶液浓度范围是0.1~5 mg/L。 本标准不适用于在还原、显色过程中引起干扰、产生不正常颜色和含有强氧化剂或还原剂及有机化合物的水样中可溶性二氧化硅的测定。

Determination method of soluble silica in coal mine water

MT/T 254-2000 煤矿水中铵离子的测定方法

本标准规定用纳氏试剂比色法测定煤矿水中的按离子。 本标准适用于煤矿水中钱离子的测定。在本标准规定条件下，测定按离子的溶液浓度范围是0.1~10 mg/L。稀释水样可扩大侧定范围。

Determination method of ammonium ion in coal mine water

MT/T 253-2000 煤矿水中硝酸根离子的测定方法

本标准规定了二磺酸酚比色法测定煤矿水中的硝酸根离子. 本标准适用于煤矿水中硝酸根离子的测定，在本标准规定的条件下，测定硝酸根离子的溶液浓度范围是0.2~8 mg/L。

Determination method of nitrate ion in coal mine water

MT/T 252-2000 煤矿水中钾离子和钠离子的测定方法

本标准规定了用原子吸收分光光度法测定煤矿水中的钾离子和钠离子。 本标准适用于煤矿水中的钾离子和钠离子的测定，测定钾离子、钠离子的溶液浓度范围是0.1~4.0 mg/L。

Determination method of potassium ion and sodium ion in coal mine water

MT/T 251-2000 煤矿水中亚硝酸根离子的测定方法

本标准规定了用N-(1-萘基)-1,2-乙二胺二盐酸盐比色法测定煤矿水中的亚硝酸根离子。 本标准适用于煤矿水中亚硝酸根离子的测定，在本标准规定条件下，侧定亚硝酸根离子的溶液浓度范围是0.1 2~2.5 mg/L。

Determination method of nitrite ion in coal mine water