E43 石油沥青 标准查询与下载

EN 15626:2016 沥青和沥青粘合剂 通过水浸试验测定稀释和流动沥青粘合剂的粘附性 骨料法

This European Standard specifies a method for the determination of the adhesivity of cut-back and fluxed bituminous binders coated onto aggregate when immersed in water. WARNING - The use of this document may involve hazardous materials, operations and equipment. This standard does not purport to address all of the safety problems associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and to determine the applicability of regulatory limitations prior to use. For environmental reasons and to reduce emissions to air, water and soil, it is recommended to limit the use of products, solvents and energy to the minimum required for a valid test result.

Bitumen and bituminous binders - Determination of adhesivity of cut-back and fluxed bituminous binders by water immersion test - Aggregate method

EN 12697-25:2016 沥青混合物-试验方法-第25部分:循环压缩试验

This European Standard specifies three test methods (A1, A2 and B) for determining the resistance of bituminous mixtures to permanent deformation by cyclic compression tests with confinement. The tests make it possible to rank various mixtures or to check on the acceptability of a given mixture. They do not allow making a quantitative prediction of rutting in the field to be made. Test methods A1 and A2 describe methods for determining the creep characteristics of bituminous mixtures by means of a uniaxial cyclic compression test with some confinement present. In this test a cylindrical test specimen is subjected to a cyclic axial stress. Method A2 is preferred for mastic asphalt and Method A1 for other asphalt mixtures. To achieve a certain confinement, the diameter of the loading platen is taken smaller than that of the test specimen. In test method A1, the test specimen is loaded by block-pulses whereas in method A2 haversine loading with rest time is applied. Test method B describes the method for determining the creep characteristics of bituminous mixtures by means of the triaxial cyclic compression test. In this test a cylindrical test specimen is subjected to a defined confining stress and a cyclic axial stress. This test is most often used for the purpose of evaluation and development of new types of mixtures. This European Standard applies to test specimens prepared in the laboratory or cored from the road. The maximum size of the aggregates is 32 mm. NOTE 1 Confinement of the test specimen is necessary to simulate realistic rutting behaviour, especially for gap-graded mixtures with a large stone fraction. NOTE 2 For the purpose of Type Testing, the test conditions are given in EN 13108-20.

Bituminous mixtures - Test methods - Part 25: Cyclic compression test

BS EN 13108-7:2016 沥青混合物 材料规格 多孔沥青

Bituminous mixtures. Material specifications. Porous Asphalt

BS EN 13924-1:2015 沥青和沥青粘合剂 特殊铺路级沥青的规范框架 硬质摊铺级沥青

Bitumen and bituminous binders. Specification framework for special paving grade bitumen. Hard paving grade bitumens

BS EN 13108-20:2016 沥青混合物 材料规格 型式试验

Bituminous mixtures. Material specifications. Type Testing

BS EN 13108-3:2016 沥青混合物 材料规格 软沥青

Bituminous mixtures. Material specifications. Soft Asphalt

BS EN 13108-4:2016 沥青混合物.材料规范.热压制沥青

Bituminous mixtures. Material specifications. Hot Rolled Asphalt

BS EN 13108-5:2016 沥青混合物 材料规格 石乳香沥青

Bituminous mixtures. Material specifications. Stone Mastic Asphalt

BS EN 13108-8:2016 沥青混合物 材料规格 再生沥青

Bituminous mixtures. Material specifications. Reclaimed asphalt

BS EN 13108-1:2016 沥青混合物 材料规格 沥青混凝土

Bituminous mixtures. Material specifications. Asphalt Concrete

BS EN 13108-9:2016 沥青混合料. 材料规格. 超薄层沥青 (AUTL)

Bituminous mixtures. Material specifications. Asphalt for Ultra-Thin Layer (AUTL)

BS EN 13108-21:2016 沥青混合物 材料规格 工厂生产控制

Bituminous mixtures. Material specifications. Factory Production Control

BS EN 13108-2:2016 沥青混合物 材料规格 极薄层沥青混凝土(BBTM)

Bituminous mixtures. Material specifications. Asphalt Concrete for Very Thin Layers (BBTM)

BS EN 13108-6:2016 沥青混合物 材料规格 沥青密封胶

Bituminous mixtures. Material specifications. Mastic Asphalt

EN 13108-2:2016 沥青混合物.材料规范.第2部分:极薄层沥青混凝土

This European Standard specifies requirements for mixtures of the mix group Asphalt Concrete for Very Thin Layers for use on roads, airfields and other trafficked areas. Asphalt Concrete for Very Thin Layers is a bituminous material, of which the composition and the grading of the aggregate is selected for application of the material in very thin layers with a thickness of 20 mm to 30 mm. Mixtures utilizing bitumen emulsion and bituminous materials based on in situ recycling are not covered by this standard. Asphalt Concrete for Very Thin Layers is used for surface courses. This European Standard includes requirements for the selection of the constituent materials. It is designed to be read in conjunction with EN 13108-20 and EN 13108-21.

Bituminous mixtures - Material specifications - Part 2: Asphalt Concrete for Very Thin Layers (BBTM)

EN 13108-20:2016 沥青混合物.材料规范.第20部分:类型试验

This European Standard specifies the Type Testing procedure for use in Assessment and Verification of the Constancy of Performance (AVCP) of bituminous mixtures for use in roads, airfields and other trafficked areas.

Bituminous mixtures - Material specifications - Part 20: Type Testing

EN 13108-9:2016 沥青混合料 材料规范 第9部分：超薄层沥青（AUTL）

This European Standard specifies requirements of Asphalt for Ultra-Thin-Layers (AUTL) for use on roads, airfields and other trafficked areas. AUTL is a hot mix asphalt road surface course laid on a bonding layer, at a nominal thickness between 10 mm and 20 mm with properties suitable for the intended use. The method of bonding is an essential part of the process and the final product is a combination of the bonding system and the bituminous mixture. The method of bonding of AUTL is out of the scope of this European Standard. Mixtures utilizing bitumen emulsion and bituminous materials based on in situ recycling are not covered by this standard. This European Standard includes requirements for the selection of the constituent materials. It is designed to be read in conjunction with EN 13108-20 and EN 13108-21.

Bituminous mixtures - Material specifications - Part 9: Asphalt for Ultra-Thin Layer (AUTL)

EN 13108-8:2016 沥青混合物-材料规范-第8部分:再生沥青

This European Standard specifies requirements for the classification and description of reclaimed asphalt as a constituent material for asphalt mixtures. It is not a standard for compliance. This European Standard only specifies reclaimed asphalt with bituminous binders, such as: paving grade bitumen, modified bitumen or hard grade bitumen. Reclaimed asphalt contaminated with coal tar or other additives or components above hazardous levels is not covered by this standard and will need to be considered under Member State Environmental, and Health and Safety Regulations.

Bituminous mixtures - Material specifications - Part 8: Reclaimed asphalt

EN 13108-1:2016 沥青混合物-材料规范-第1部分:沥青混凝土

This European Standard specifies requirements for mixtures of the mix group Asphalt Concrete for use on roads, airfields and other trafficked areas. Asphalt Concrete is used for surface courses, binder courses, regulating courses, and bases. The mixtures of the mix group Asphalt Concrete are produced on the basis of hot bitumen. Mixtures utilizing bitumen emulsion and bituminous materials based on in situ recycling are not covered by this standard. This European Standard includes requirements for the selection of the constituent materials. It is designed to be read in conjunction with EN 13108-20 and EN 13108-21.

Bituminous mixtures - Material specifications - Part 1: Asphalt Concrete

EN 13108-6:2016 沥青混合物-材料规范-第6部分:石油沥青砂胶

This European Standard specifies requirements for mixtures of the mix group Mastic Asphalt for use on roads, airfields and other trafficked areas. Mastic Asphalt is used for surface courses, binder courses, protection layers and inter-layers for bridges, tunnels and troughs. The mixtures of the mix group Mastic Asphalt are produced on the basis of hot bitumen. Mixtures utilizing bitumen emulsion and bituminous materials based on in situ recycling are not covered by this standard. This European Standard includes requirements for the selection of the constituent materials. It is designed to be read in conjunction with EN 13108-20 and EN 13108-21.

Bituminous mixtures - Material specifications - Part 6: Mastic Asphalt