共找到 1705 条与 钢管、铸铁管 相关的标准,共 114 页
This document specifies requirements for seamless and welded steel pipes of two product specification levels (PSL 1 and PSL 2) for use in pipeline transportation systems in the petroleum and natural gas industries
Petroleum and natural gas industries - Steel pipe for pipeline transportation systems (ISO 3183:2012 + Amd 1:2017); German version EN ISO 3183:2012 + A1:2018
Ductile iron patcher for pipes
Carbon steel and low alloy steel for pressurized water reactor nuclear power plants Part 41: Low alloy steel pipes for safety grade equipment
Polyethylene coated steel pipes -- Part 2: External extruded polyethylene coated steel pipes
Steel heat exchanger tubes for low temperature service
Carbon steel tubes for cylinder barrels
Electric resistance welded carbon steel tubes for automobile
Steel pipes for low temperature service
Seamless steel tubes for high pressure gas cylinders
Ductile iron pipes, fittings, accessories and their joints - Thermal preinsulated products
1.1 This specification2 covers a group of general requirements that, unless otherwise specified in an individual specification, shall apply to the ASTM product specifications noted below. 1.2 In the case of conflict between a requirement of a product specification and a requirement of this specification, the product specification shall prevail. In the case of conflict between a requirement of the product specification or a requirement of this specification and a more stringent requirement of the purchase order, the purchase order shall prevail. Title of Specification ASTM Desig- nation3 Seamless, Welded, and Heavily Cold Worked Austenitic Stainless Steel Pipes A312/A312M Seamless and Welded Steel Pipe for Low-Temperature Service and Other Applications with Required Notch Toughness A333/A333M Seamless Ferritic Alloy-Steel Pipe for High Temperature Service A335/A335M Electric-Fusion-Welded Austenitic Chromium-Nickel Stainless Steel Pipe for High-Temperature Service and General Applications A358/A358M Carbon and Ferritic Alloy Steel Forged and Bored Pipe for High-Temperature Service A369/A369M Seamless Austenitic Steel Pipe for High-Temperature Service A376/A376M Welded Large Diameter Austenitic Steel Pipe for Corrosive or High-Temperature Service A409/A409M
Standard Specification for General Requirements for Alloy and Stainless Steel Pipe
1.1 This specification2 covers seamless and straight-seam welded ferritic/austenitic steel pipe intended for general corrosive service, with particular emphasis on resistance to stress corrosion cracking. These steels are susceptible to embrittlement if used for prolonged periods at elevated temperatures. 1.2 Optional supplementary requirements are provided for pipe when a greater degree of testing is desired. These supplementary requirements call for additional tests to be made and, when desired, one or more of these may be specified in the order. 1.3 Appendix X1 of this specification lists the dimensions of welded and seamless stainless steel pipe as shown in ANSI B36.19. Pipe having other dimensions may be furnished provided such pipe complies with all other requirements of this specification. 1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. The inch-pound units shall apply unless the M designation of this specification is specified in the order. Note 1: The dimensionless designator NPS (nominal pipe size) has been substituted in this standard for such traditional terms as nominal diameter, size, and nominal size. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Standard Specification for Seamless and Welded Ferritic/Austenitic Stainless Steel Pipe
1.1 This specification2 covers nominal wall and minimum wall seamless ferritic alloy-steel pipe intended for high-temperature service. Pipe ordered to this specification shall be suitable for bending, flanging (vanstoning), and similar forming operations, and for fusion welding. Selection will depend upon design, service conditions, mechanical properties, and high-temperature characteristics. 1.2 Several grades of ferritic steels (see Note 1) are covered. Their compositions are given in Table 1. Note 1: Ferritic steels in this specification are defined as low- and intermediate-alloy steels containing up to and including 108201;% chromium. (A) New designation established in accordance with Practice E527 and SAE J1086, Practice for Numbering Metals and Alloys (UNS).(B) Grade P5c shall have a titanium content of not less than 4 times the carbon content and not more than 0.708201;%; or a columbium content of 8 to 10 times the carbon content.(C) Alternatively, in lieu of this ratio minimum, the material shall have a minimum hardness of 275 HV in the hardened condition, defined as after austenitizing and cooling to room temperature but prior to tempering. Hardness testing shall be performed at mid-thickness of the product. Hardness test frequency shall be two samples of product per heat treatment lot and the hardness testing results shall be reported on the material test report.(D) Applies to both heat and product analyses. 1.3 Supplementary requirements (S1 to S8) of an optional nature are provided. Supplementary requirements S1 through S6 call for additional tests to be made, and when desired, shall be so stated in the order together with the number of such tests required. 1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. The inch-pound units shall apply unless the “M” designation of this specification is specified in the order. Note 2: The dimensionless designator NPS (nominal pipe size) has been substituted in this standard for such traditional terms as “nominal diameter,” “size,” and “nominal size.”
Standard Specification for Seamless Ferritic Alloy-Steel Pipe for High-Temperature Service
1.1 This specification covers special hubless cast iron soil pipe fittings for use in a one-pipe combination vent and waste stack unvented for gravity flow applications. It establishes standards covering material, manufacture, mechanical and chemical properties, dimensions, coating, test methods, inspection, certification, and product marking for hubless cast iron soil pipe fittings. These fittings are intended for nonpressure applications, where the selection of the proper size for sanitary, drain, and waste systems allows free air space for gravity drainage. Note 1: The fittings covered by this standard are special fittings intended to be used for engineered designed systems and will require special approval by the authority having jurisdiction for use. It is not the intent of this standard to endorse or recommend the use of these fittings for these special applications. 1.2 The EDP/ASA numbers indicated in this section represent a uniform industry code adopted by the American Supply Association (ASA). A group designation prefix, 022, is assigned to hubless products, followed by the four-digit identification assigned to individual items and a check digit. This system has been instituted to facilitate EDP control through distribution channels, and is to be used universally in ordering and specifying product items. Those items with no EDP numbers are new, special, or transitory, and will be assigned numbers on subsequent prints of this specification. 1.3 This specification covers fittings of the following patterns and applies to any other patterns that conform with the applicable requirements given in this specification. Note 2: The text of this standard references notes and footnotes that provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard. Note 3: Some sellers of these fittings use the terms “aerator” and “de-aerator” fittings to describe the two types of fittings covered by this standard. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Standard Specification for Special Fittings for Single-Stack Hubless Cast Iron Soil Pipe Fittings for Sanitary, Waste, and Vent Piping Applications
Stainless steel welded steel pipes for medical gases and vacuums
Ceramic lined composite steel pipe
Petroleum and natural gas industries - Steel pipe for pipeline transportation systems; Amendment 1
Stainless steel pipes (Amendment 1)
Large diameter welded stainless steel pipes (Amendment 1)
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号