H57 高温合金 标准查询与下载

GB/T 14994-2008 高温合金冷拉棒材

本标准规定了高温合金冷拉棒材的尺寸、外形及允许偏差、技术要求、试验方法、检验规则、包装、标志及质量证明书等。 本标准适用于高温合金冷拉棒材，可用于制造工业用紧固件等零件。

Superalloy cold drawn bars

GB/T 15062-2008 一般用途高温合金管

本标准规定了一般用途高温合金冷拔（轧）无缝管的尺寸、外形及允许偏差、技术要求、试验方法、检验规则、包装、标志及质量证明书。 本标准适用于在高温下承力不大的冷拔（轧）高温合金管材。

Superalloy tube for general application

GB/T 14992-2005 高温合金和金属间化合物高温材料的分类和牌号

本标准规定了高温合金和金属间化合物高温材料的分类、牌号的命名原则、命名程序及一般化学成分等内容。本标准适用于变形高温合金、铸造高温合金（等轴晶铸造高温合金、定向凝固柱晶高温合金和单晶高温合金）、焊接用高温合金丝、粉末冶金高温合金、弥散强化高温合金和金属间化合物高温材料。

Classification and designation for superalloys and high temperature intermetallic materials

GB/T 43484-2023 增材制造 激光粉末床熔融用高温合金粉末

High temperature alloy powder for laser powder bed fusion for additive manufacturing

YB/T 6123-2023 高温合金精密无缝管

本文件规定了高温合金精密无缝管的订货内容、尺寸、外形、技术要求、试验方法、检验规则、包装、标志和质量证明书。本文件适用于公称外径3.0mm～51.0mm、壁厚0.2mm～5.0mm的冷轧（拔）高温合金精密无缝管。

High temperature alloy precision seamless pipe

ISO 4955:2016 耐热钢

Heat-resistant steels

NB/T 20008.16-2012 压水堆核电厂用其他材料 第16 部分：控制棒驱动机构用钴基合金

本部分规定了压水堆核电厂控制棒驱动机构用GH5605钴基合金棒材的制造、化学成分、力学性能、金相检验、无损检测等技术要求。本部分适用于压水堆核电厂控制棒驱动机构钩爪销轴、连杆销轴和胀头用GH5605钴基合金圆形棒材。

Other material for pressurized water reactor nuclear power plants.Part 16:Cabolt-base alloy for control rod drive mechanism

ASTM A1077/A1077M-12 建筑用高温下增加屈服的结构钢的标准规格

1.1 This specification covers alloy steel in bars, plates up to and including 4 in. [100 mm] in thickness and shapes of structural quality with improved yield strength at high temperature. Two grades, 36 [250] and 50 [345] are available for use in bolted or welded buildings or for general structural purposes. Class 2 requires a maximum yield to tensile ratio – this ratio is not required for Class 1. 1.2 When the steel is to be welded, a welding procedure suitable for the grade of steel and intended use or service is to be utilized. See Appendix X3 of Specification A6/A6M for information on weldability. 1.3 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system is to be used independently of the other, without combining values in any way. 1.4 The text of this specification contains notes or footnotes, or both, that provide explanatory material. Such notes and footnotes, excluding those in tables and figures, do not contain any mandatory requirements. 1.5 For structural products produced from coil and furnished without heat treatment or with stress relieving only, the additional requirements, including additional testing requirements and the reporting of additional test results, of Specification A6/A6M apply. 1.6 Supplementary requirements are provided for use where additional testing or additional restrictions are required by the purchaser. Such requirements apply only when specified in the purchase order.

Standard Specification for Structural Steel with Improved Yield Strength at High Temperature for Use in Buildings

JIS G 4107 AMD 1:2010 高温设备用合金钢螺栓材料

Alloy steel bolting materials for high temperature service (Amendment 1)

KS D ISO 4955:2008 耐热钢和耐热合金

1.1 이 표준은 고온 가스와 550 ℃ 이상의 온도에서 발생하는 연소 생성물의 영향에 견

Heat-resisting steels and alloys

JIS G 3119:2007 锅炉和压力容器用锰-钼和锰-钼-镍合金钢厚板材

この規格は，中温かち高温で使用されるボイラ及び圧力容器に用いるマンガンモリブデン鋼及びマンガンモリブデンニッケル鋼の熱間圧廷鋼板(以下，鋼板という。)にいて規定する。

Manganese-molybdenum and manganese-molybdenum-nickel alloy steel plates for boilers and pressure vessels

JIS G 4107:2007 高温设备用合金钢螺栓连接材料

この規格は，主として高温で使用される圧力容器，バルブ，フランジ及び継手に用いる合金鋼ボルト材(以下，ボルト材という。)について規定する。ここでいうボルト材とは，棒鋼，線材，ねじ加工を行っていないボルト及び植込ボルトなどを指す。

Alloy steel bolting materials for high temperature service

ASTM B527-06 测定金属粉末及化合物的塔普(Tap)密度的标准试验方法

This test method covers the evaluation of the tapped density physical characteristic of metallic powders and compounds. The degree of correlation between the results of this test method and the quality of powders in use will vary with each particular application and has not been fully determined.1.1 This test method specifies a method for the determination of tap density (packed density) of metallic powders and compounds, that is, the density of a powder that has been tapped, to settle contents, in a container under specified conditions.This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Determination of Tap Density of Metallic Powders and Compounds

ISO 4955:2005 耐热钢

1 This International Standard specifies requirements for the grades of wrought steels, listed in Table 1, which are usually employed for products for which the resistance to the effects of hot gases and the products of combustion at temperatures in the region above 550 ℃ is the main requirement. 2 This International Standard is applicable to — flat products; — bars; — sections; — wire and rod; — forgings. NOTE 1 Heat-resisting steels for valves are covered by ISO 683-15. NOTE 2 Corrosion-resistant stainless steels for which resistance to corrosion is of primary importance are covered by ISO 16143-1, ISO 16143-2 and ISO 16143-3. NOTE 3 Not all of the steels included in this International Standard are necessarily available in all product forms. NOTE 4 Wire in the cold-worked condition is covered by ISO 16143-3. 3 In addition to this International Standard, the general technical delivery requirements of ISO 404 are applicable.

Heat-resistant steels

DIN 17440:2001 不锈钢.拉制丝材的交货技术条件

Stainless steels - Technical delivery conditions for drawn wire

ASTM A181/A181M-00 通用管道的碳素钢锻件用标准规范

1.1 This specification covers nonstandard as-forged fittings, valve components, and parts for general service. Forgings made to this specification are limited to a maximum weight of 10 000 lb [4540 kg]. Larger forgings may be ordered to Specification A266/A266M. 1.2 Two grades of material are covered, designated as Classes 60 and 70, respectively, and are classified in accordance with their chemical composition and mechanical properties as specified in 5.1 and 6.1. 1.3 Class 60 was formerly designated Grade I and Class 70 was formerly designated Grade II. 1.4 This specification is expressed in both inch-pound units and SI units. However, unless the order specifies the applicable "M" specification designation (SI units), the material shall be furnished to inch-pound units. 1.5 The values stated in either inch-pound units or SI units are to be regarded as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with the specification.

Standard Specification for Carbon Steel Forgings, for General-Purpose Piping

NAVY MIL-T-23132 A NOTICE 3-1998 钨迟滞合成物

MIL-T-23 132A, dated 16 June 1972, and Amendment 1, dated 3 January 1973, are hereby reactivated and may be used for either new or existing design acquisition.

TUNGSTEN DELAY COMPOSITION

HB 5220.29-1995 高温合金化学分析方法 重铬酸钾容量法测定铁含量

本标准规定了用重铬酸钾容量法测定高温合金中铁含量的方法提要、试剂、分析步骤、分析结果的计算和允许差。 　　本标准适用于镍基和钴基高温合金中铁含量的测定。

Superalloy Chemical Analysis Method Potassium Dichromate Volumetric Method for Determination of Iron Content

HB 5220.30-1995 高温合金化学分析方法 邻菲罗啉吸光光度法测定铁含量

本标准规定了用邻菲罗啉吸光光度法测定高温合金中铁含量的方法提要、试剂、分析步骤、工作曲线的绘制、分析结果的计算和允许差。 　　本标准适用于镍基和钴基高温合金中铁含量的测定。

Superalloy chemical analysis method o-phenanthroline absorptiophotometry determination of iron content

ISO 4955:1994 耐热钢和耐热合金

Heat-resisting steels and alloys