H63 稀有高熔点金属及其合金 标准查询与下载

ASTM B658/B658M-11e1 无缝和焊接锆和锆合金焊接配件的标准规格

1.1 This specification covers three grades of seamless and welded zirconium pipe. 1.2 Unless a single unit is used, for example corrosion mass gain in mg/dm2, the values stated in either inch-pound or SI units are to be regarded separately as standard. The values stated in each system are not exact equivalents; therefore each system must be used independently of the other. SI values cannot be mixed with inch-pound values. 1.3 The following precautionary caveat pertains only to the test methods portions of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Seamless and Welded Zirconium and Zirconium Alloy Pipe

ASTM B352/B352M-11(2016) 核应用用锆和锆合金薄板、带材和板材的标准规范

1.1 This specification covers hot- and cold-rolled zirconium and zirconium alloy sheet, strip, and plate. 1.2 One unalloyed and three alloys for use in nuclear applications are described. 1.3 The products covered in this specification include the following forms and sizes: 1.3.1 Sheet, 24 in. [600 mm] or more in width; under 0.187 in. [4.8 mm) in thickness, 1.3.2 Strip, less than 24 in. [600 mm] in width; under 0.187 in. [4.8 mm] in thickness, and 1.3.3 Plate, over 10 in. [250 mm] in width; 0.187 in. [4.8 mm] and over in thickness. Note 1: Material over 0.187 in. [4.8 mm] in thickness and less than 10 in. [250 mm] wide is covered as bar in Specification B351/B351M. 1.4 Unless a single unit is used, for example corrosion mass gain in mg/dm2, the values stated in either inch-pound or SI units are to be regarded separately as standard. The values stated in each system are not exact equivalents; therefore each system must be used independently of the other. SI values cannot be mixed with inch-pound values. 1.5 The following precautionary caveat pertains only to the test method portions of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Zirconium and Zirconium Alloy Sheet, Strip, and Plate for Nuclear Application

ASTM B352/B352M-11 核应用锆及锆合金板,薄板和带材标准规格

1.1 This specification covers hot- and cold-rolled zirconium and zirconium alloy sheet, strip, and plate. 1.2 One unalloyed and three alloys for use in nuclear applications are described. 1.3 The products covered in this specification include the following forms and sizes: 1.3.1 Sheet, 24 in. [600 mm] or more in width; under 0.187 in. [4.8 mm) in thickness, 1.3.2 Strip, less than 24 in. [600 mm] in width; under 0.187 in. [4.8 mm] in thickness, and 1.3.3 Plate, over 10 in. [250 mm] in width; 0.187 in. [4.8 mm] and over in thickness. Note 18212;Material over 0.187 in. [4.8 mm] in thickness and less than 10 in. [250 mm] wide is covered as bar in Specification B351/B351M. 1.4 Unless a single unit is used, for example corrosion mass gain in mg/dm2, the values stated in either inch-pound or SI units are to be regarded separately as standard. The values stated in each system are not exact equivalents; therefore each system must be used independently of the other. SI values cannot be mixed with inch-pound values. 1.5 The following precautionary caveat pertains only to the test method portions of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Zirconium and Zirconium Alloy Sheet, Strip, and Plate for Nuclear Application

ASTM B884-11 用于超导的铌钛合金坯料,棒材和条材标准规格

1.1 This specification covers niobium-titanium alloy billets, bars, and rods, at 46 to 48 % titanium. This material is used in the manufacture of wire for superconducting applications. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 The following precautionary caveat pertains only to the test methods portion, Section 14, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Niobium-Titanium Alloy Billets, Bar, and Rod for Superconducting Applications

ASTM B658/B658M-11 无缝和焊接锆和锆合金管标准规格

1.1 This specification covers three grades of seamless and welded zirconium pipe. 1.2 Unless a single unit is used, for example corrosion mass gain in mg/dm2, the values stated in either inch-pound or SI units are to be regarded separately as standard. The values stated in each system are not exact equivalents; therefore each system must be used independently of the other. SI values cannot be mixed with inch-pound values. 1.3 The following precautionary caveat pertains only to the test methods portions of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Seamless and Welded Zirconium and Zirconium Alloy Pipe

ASTM B350/B350M-11 核应用锆和锆合金铸锭标准规格

For purposes of determining compliance with the specified limits for requirements of the properties listed in Table 1 and Table 2, an observed value or a calculated value shall be rounded as indicated in accordance with the rounding method of Practice E29.1.1 This specification covers vacuum-melted zirconium and zirconium alloy ingots for nuclear application. 1.2 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the specification. 1.3 The following precautionary caveat pertains only to the test method portions of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Zirconium and Zirconium Alloy Ingots for Nuclear Application

ASTM B350/B350M-11(2016) 核设备用锆和锆合金锭标准规范

10.1 For purposes of determining compliance with the specified limits for requirements of the properties listed in Table 1 and Table 2, an observed value or a calculated value shall be rounded as indicated in accordance with the rounding method of Practice E29. 1.1 This specification covers vacuum-melted zirconium and zirconium alloy ingots for nuclear application. 1.2 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the specification. 1.3 The following precautionary caveat pertains only to the test method portions of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Zirconium and Zirconium Alloy Ingots for Nuclear Application

ASTM B350/B350M-11(2016)e1 核设备用锆和锆合金锭规格

10.1 For purposes of determining compliance with the specified limits for requirements of the properties listed in Table 1 and Table 2, an observed value or a calculated value shall be rounded as indicated in accordance with the rounding method of Practice E29. 1.1 This specification covers vacuum-melted zirconium and zirconium alloy ingots for nuclear application. 1.2 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the specification. 1.3 The following precautionary caveat pertains only to the test method portions of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Zirconium and Zirconium Alloy Ingots for Nuclear Application

KS D 2553-2010 钽中铁含量测定方法

이 표준은 탄탈럼의 원자 흡광 분석 방법에 대하여 규정한다.

Tantalum-Method for atomic absorption spectrometric analysis

YS/T 42-2010 钽酸锂单晶

本标准规定了钽酸锂单晶的要求、试验方法、检验规则、标志、包装、运输、贮存、质量证明书和合同(或订货单)内容。 本标准适用于提拉法生长的钽酸锂原生单晶经磨外圆后的产品。

Lithium tantalate single crystals

SAE AMS4992A-2010 热等压压制6Al 4V钛合金结构铸件

This specification covers titanium Ti 6Al-4V alloy in the form of investment castings. These castings have been used typically for structurally cast components requiring a combination of good strength-to-weight ratio and corrosion resistance, but usage is not limited to such applications.

Castings, Structural Investment, Titanium Alloy 6Al 4V Hot Isostatically Pressed

ASTM B495-10 锆和锆合金铸锭的标准规范

1.1 This specification covers six grades of zirconium ingots. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 The following precautionary caveat pertains only to the test method portion, Section 10, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Zirconium and Zirconium Alloy Ingots

ASTM B495-10(2017) 锆及锆合金锭的标准规格

1.1 This specification covers six grades of zirconium ingots. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.3 The following precautionary caveat pertains only to the test method portion, Section 10, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Zirconium and Zirconium Alloy Ingots

ASTM B654/B654M-10 铌-铪合金箔材、薄板材、带材和厚板材的标准规范

1.1 This specification covers hafnium alloyed niobium foil, sheet, strip, and plate. 1.2 The material covered by this specification is R04295, niobium-base alloy containing approximately 10 % hafnium and 1 % titanium. 1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.4 The following safety hazards caveat pertains only to the test methods portion, Section 14, of this specification: This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Niobium-Hafnium Alloy Foil, Sheet, Strip, and Plate

ASTM B614-10 锆及锆合金表面的除垢和清洗的标准实施规程

1.1 This practice covers a cleaning and descaling procedure useful to producers, users, and fabricators of zirconium and zirconium alloys for the removal of ordinary shop soils, oxides, and scales resulting from heat treatment operations and foreign substances present as surface contaminants. 1.2 It is not intended that these procedures become mandatory for removal of any of the indicated soils but rather serve as a guide when zirconium and zirconium alloys are being processed in the wrought, cast, or fabricated form. 1.3 It is the intent that these soils be removed prior to chemical milling, joining, plating, welding, fabrication, and in any situation where foreign substances interfere with the corrosion resistance, stability, and quality of the finished product. 1.4 Unless a single unit is used, for example, solution concentrations in g/l, the values stated in either inch-pound or SI units are to be regarded separately as standard. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. SI values cannot be mixed with inch-pound values. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific hazard statements, see Sections 2 and 6.

Standard Practice for Descaling and Cleaning Zirconium and Zirconium Alloy Surfaces

ASTM B387-10 钼及钼合金棒材、杆材和线材的标准规范

1.1 This specification covers unalloyed molybdenum and molybdenum alloy bar, rod, and wire as follows: 1.1.1 Molybdenum 3608212;Unalloyed vacuum arc-cast molybdenum. 1.1.2 Molybdenum 3618212;Unalloyed powder metallurgy molybdenum. 1.1.3 Molybdenum Alloy 3638212;Vacuum arc-cast molybdenum-0.5% titanium-0.1% zirconium (TZM) alloy. 1.1.4 Molybdenum Alloy 3648212;Powder metallurgy molybdenum-0.5% titanium-0.1% zirconium (TZM) alloy. 1.1.5 Molybdenum 3658212;Unalloyed vacuum arc-cast molybdenum, low carbon. 1.1.6 Molybdenum Alloy 3668212;Vacuum arc-cast molybdenum, 30% tungsten alloy. 1.2 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are provided for information purposes only.

Standard Specification for Molybdenum and Molybdenum Alloy Bar, Rod, and Wire

YS/T 718-2009 平面磁控溅射靶材.光学薄膜用铌靶

本标准规定了平面磁控溅射光学薄膜用铌靶材的要求、试验方法、检验规则、标志、包装、运输、贮存、订货单(合同)内容。 本标准适用于平面磁控溅射光学薄膜用铌靶材。

Flat magneting sputtering target.Niobium target for optical coating

YS/T 719-2009 平面磁控溅射靶材.光学薄膜用硅靶

本标准规定了平面磁控溅射光学薄膜用硅靶材的要求、试验方法、检验规则、标志、包装、运输、贮存、订货单(合同)内容。 本标准适用于平面磁控溅射光学薄膜用硅靶材。

Flat magneting sputtering target.Silicon target for optical coating

YS/T 692-2009 钨酸

本标准规定了钨酸的要求、试验方法、检验规则、标志、包装、运输、贮存、订货单(合同)等内容。 本标准适用于催化剂、印染助剂，润滑剂，以及塑料工业和陶瓷工业等用的钨酸。

Tungstic acid

KS D 5545-2009 铜和铜合金焊接管

이 표준은 KS D 5201에서 규정하는 C 1220, C 2600, C 2680, C 4

Copper and copper alloy welded pipes and tubes