H70 粉末冶金综合 标准查询与下载

ISO 3954:2007 粉末冶金用粉末.取样

This International Standard specifies procedures for the sampling of powders for powder metallurgical purposes. lt also covers the splitting of the sample into the quantity required for testing.

Powders for powder metallurgical purposes - Sampling

ASTM B853-07 粉末冶金(P/M)硼不锈钢构件的标准规范

1.1 This specification covers stainless steel powder metallurgy (PM) structural components with a 7.7-g/cm3 minimum density that are fabricated from prealloyed powder consisting primarily of iron, chromium, nickel, molybdenum, and boron and are intended for use in corrosive service. 1.2 With the exception of density values, for which g/cm3 is the industry standard, the values stated in inch-pound units are to be regarded as the standard. The SI values given in parentheses are converted in accordance with IEEE/ASTM SI 10 and are for information only.

Standard Specification for Powder Metallurgy (PM) Boron Stainless Steel Structural Components

ASTM B795-07 粉末锻造(PF)钢材料中合金或非合金铁杂质百分比的测定用标准试验方法

Cross product contamination occurs whenever alloy steel powders are processed in the same equipment as iron powders. Unalloyed iron particles, because they may not harden upon heat treatment, are a potential source of soft spots in low-alloy steel parts. Alloyed iron particles, having higher hardenability than an iron or carbon steel matrix, are a potential source of hard spots. Hard or soft spots may cause problems in service or machining. The results of the tests may be used to qualify parts for shipment in accordance with guidelines agreed between purchaser and manufacturer or to check the suitability of mixes for use in powder forging. 1. Scope1.1 This test method covers a metallographic procedure for determining the percentage of alloyed or unalloyed iron contamination present in powder forged low-alloy steel materials and the percentage of alloyed iron contamination in powder forged iron and carbon steel materials.1.2 Property values stated in SI units are the standard.This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Determining the Percentage of Alloyed or Unalloyed Iron Contamination Present in Powder Forged (PF) Steel Materials

ISO 7625:2006 不包括硬质金属的烧结金属材料.碳含量测定用化学分析样品的制备

This International Standard specifies methods for preparing a sample from one or more sintered parts of materials to be analysed for free or total carbon content. Combined carbon is determined as the difference between total and free carbon. This standard covers the preparation of samples for the determination of carbon by a chemical method, i.e. combustion in oxygen and measurement of the carbon dioxide produced, in accordance with ISO 437. It does not cover the preparation of samples for carbon determination by physical methods, such as metallography or spectroscopy.

Sintered metal materials, excluding hardmetals - Preparation of samples for chemical analysis for determination of carbon content

JIS Z 2511:2006 金属粉末.通过矩形坯块的横向断裂测定生坯强度

この規格は，断面が長方形の圧粉体での抗折試験によって，金属粉の圧粉体強さを測定する方法について規定する。

Metallic powders -- Determination of green strength by transverse rupture of rectangular compacts

JIS Z 2512:2006 金属粉末.堆积密度的测定

この規格トよ，タップ密度[定められた条件下で容器をタップ(振動)して得られる金属粉(以下，粉末とし、う。)の密度]を測定する方法について規定する。

Metallic powders -- Determination of tap density

DIN EN ISO 3738-2:2006 硬质合金.洛氏硬度试验(A标尺).第2部分:标准试块的制备及校准

Hardmetals - Rockwell hardness test (scale A) - Part 2: Preparation and calibration of standard test blocks (ISO 3738-2:1988); English version of DIN EN ISO 3738-2:2006-06

DIN EN ISO 4022:2006 可渗透性烧结金属材料.液体渗透性的测定

This document specifies a method for the determination of the fluid permeability of permeable sintered metal materials in which the porosity is deliberately continuous or interconnecting.

Permeable sintered metal materials - Determination of fluid permeability (ISO 4022:1987); English version of DIN EN ISO 4022:2006-06

DIN EN ISO 3928:2006 不包括硬质金属的烧结金属材料.疲劳试验试样

The document specifies the die cavity dimensions used for making fatique test pieces by pressing and sintering, together with certain dimensions of the test piece obtained from such a die as well as the dimensions of the test pieces machined from sintered and powder forged materials.#,,#

Sintered metal materials, excluding hardmetals - Fatigue test pieces (ISO 3928:1999); English version of DIN EN ISO 3928:2006-06

DIN EN ISO 4491-3:2006 金属粉末.用还原法测定氧含量.第3部分:可被氢还原的氧量

This document specifies a method for the determination of the reducible oxygen content of metallic powders in the range 0,05 % to 3 % (m/m) oxygen.#,,#

Metallic powders - Determination of oxygen content by reduction methods - Part 3: Hydrogen-reducible oxygen (ISO 4491-3:1997); English version of DIN EN ISO 4491-3:2006-06

BS EN ISO 4491-3:2006 金属粉末.用还原法测定氧含量.可被氢还原的氧量

This part of ISO 4491 specifies a method for the determination of the hydrogen-reducible oxygen content of metallic powders containing 0,05 % (m/m) to 3 % (m/m) oxygen. The method is applicable to unalloyed, partially alloyed or completely alloyed metal powders and also to mixtures of carbides and binder metal. It is not applicable to powders containing lubricants or organic binders. The method may be extended to powders containing carbon by the use of a special catalytic device. This part of ISO 4491 shall be read in conjunction with ISO 760 and ISO 4491-1.

Metallic powders - Determination of oxygen content by reduction methods - Hydrogen-reducible oxygen

BS EN ISO 3738-2:2006 硬质合金.洛氏硬度试验(等级A).标准试验块的准备和校验

Specifies primary standard test blocks, secondary standard test blocks and working standard test blocks calibrated from master standard test blocks to be used for the verification of Rockwell hardness testing machines and indenters for testing hardmetals. This part of ISO 3738 should be read in conjunction with ISO 3738-1.

Hardmetals - Rockwell hardness test (scale A) - Preparation and calibration of standard test blocks

KS D 1661-2005 压电陶瓷(PZT)粉末的铅定量方法.EDTA滴定法

이 규격은 압전 세라믹으로 사용되는 PZT[Pb(Zrx, Ti1-x)O3] 분말 중에 함유

Determination of lead content in PZT(Piezo Zirconate Titanate) powders－EDTA titration method

ISO 11873:2005 硬质合金.钴金属粉末中硫和碳含量的测定.红外线探测法

This International Standard specifies the method to be used for the determination of sulfur and carbon in cobalt metal powders in the range of 0,001 % (m/m) to 0,1 % (m/m) by combustion in oxygen and infrared (IR)-detection of carbon dioxide (CO2) and sulfur dioxide (SO2).

Hardmetals - Determination of sulfur and carbon contents in cobalt metal powders - Infrared detection method

DIN EN 1274:2005 热喷涂.粉末.成分、交货技术条件

This Standard covers powders, which are currently applicable in thermal spraying on the basis of the physical and chemical properties.#,,#

Thermal spraying - Powders - Composition, technical supply conditions; German version EN 1274:2004

ASTM B276-05 硬质合金表观孔隙率的标准试验方法

1.1 This test method specifies procedures for the metallographic determination of apparent porosity in cemented carbides. Note 1 The term "apparent porosity" is construed to mean all microstructures observed on a properly prepared, unetched surface, including structures resulting from uncombined carbon, non-metallic inclusions, etc., as well as true, inherent porosity.This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Apparent Porosity in Cemented Carbides

ASTM B330-05 测定金属粉末及相关化合物的费歇尔值的标准试验方法

1.1 This test method uses air permeability to determine an envelope-specific surface area and its associated average equivalent spherical diameter (from 1 to 50 m) of metal powders and related compounds. The powders may be analyzed in their "as-supplied" (shipped, received, or processed) condition or after they have been de-agglomerated or milled by a laboratory procedure ("lab milled") such as that specified in Practice B 859. The values obtained are not intended to be absolute but are generally useful on a relative basis for control purposes.1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Fisher Number of Metal Powders and Related Compounds

ASTM B895-05 通过浸入氯化钠溶液评价粉末冶金(P/M)不锈钢零件/样品的耐腐蚀性的标准试验方法

The ability of sintered powder metallurgy stainless steel parts/specimens to resist corrosion when immersed in sodium chloride solution is important to their end use. Causes of unacceptable corrosion may be incorrect alloy, contamination of the parts by iron or some other corrosion-promoting material or improper sintering of the parts (for example, undesirable carbide and nitride formations caused by poor lubricant burnoff or improper sintering atmosphere). This standard may be part of a purchase agreement between the P/M parts producer (seller) and the user of the parts (purchaser) (Method 1). It may also be used to optimize part or specimen production parameters (Method 2).1.1 These test methods cover a procedure for evaluating the ability of sintered P/M stainless steel parts/specimens to resist corrosion when immersed in a sodium chloride (NaCl) solution. 1.2 Corrosion resistance is evaluated by one of two methods. In Method 1, the stainless steel parts/specimens are examined periodically and the time to the first appearance of staining or rust is used to indicate the end point. In Method 2, continued exposure to the sodium chloride solution is used to monitor the extent of corrosion as a function of time. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Test Methods for Evaluating the Corrosion Resistance of Stainless Steel Powder Metallurgy (P/M) Parts/Specimens by Immersion in a Sodium Chloride Solution

ASTM B657-05 硬质合金中微观结构金相鉴定指南

The microstructure of a cemented carbide affects the materialrsquo;mechanical and physical properties. This guide is not intended to be used as a specification for carbide grades. Producers and users may use the microstructural information as a guide in developing their own specifications. 1.1 This test method covers apparatus and procedures for the metallographic determination of microstructures in cemented tungsten carbides. 1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Precautions applying to use of hazardous laboratory chemicals should be observed for chemicals specified in Table 1.

Guide for Metallographic Identification of Microstructure in Cemented Carbides

ASTM B939-05 粉末冶金(P/M)承重和结构材料的径向压溃强度K的标准试验方法

1.1 This test method covers the equipment and laboratory procedure for the determination of the radial crushing strength of materials using either a plain powder metallurgy (P/M) bearing or a hollow cylindrical test specimen. This is a destructive test that produces quantitative results.1.2 Limitations1.2.1 The principle of this procedure is based on the material being tested having minimal ductility. The permanent deflection of the cylinder during the test should not exceed 10 % of the outside diameter.1.2.2 The radial crushing strength test results should be used only as a guide if the test specimen has a wall thickness that is greater than one-third of the outside diameter. These test results should then only be used for comparison with data from the test specimens of like materials and similar dimensions.1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Radial Crushing Strength, K, of Powder Metallurgy (P/M) Bearings and Structural Materials