J08 标志、包装、运输、贮存 标准查询与下载

ASME SEC VIII D3 ART KS-2-2003 第KS-2.获得和使用规范钢印

Boiler and Pressure Vessels.Article KS-2 Obtaining and Using Code Stamps

Article KS-2 Obtaining and Using Code Stamps

SAE J284-2002 农业,建筑及工业设备安全警告标志

This SAE Recommended Practice presents the general uses, limitations on use, and appearance of the safety alert symbol.

Safety Alert Symbol for Agricultural, Construction and Industrial Equipment

AIA/NAS NASM91525-2001 FSC 5355型金属和塑料旋钮控制横条

THE INITIAL RELEASE OF THIS DOCUMENT SUPERSEDES MS91525, REVISION F. PART NUMBERS REMAIN MC91525

Knob Control, Bar, Metal and Plastic

ASME SEC V A-11-2001 第11条.增强型纤维塑料容器的声辐射检验

Boiler and Pressure Vessel.Article 11 Acoustic Emission Examination of Fiber-Reinforced Plastic Vessels

Article 11 Acoustic Emission Examination of Fiber-Reinforced Plastic Vessels

ASME SEC X PART RS-2001 钢印标识和报告

Boiler and Pressure Vessels.Marking, Stamping, and Reports

Marking, Stamping, and Reports

ASME SEC VIII D2 ART S-1-2001 第S-1条.钢印的内容和方法

Boiler and Pressure Vessels.Article S-1 Contents and Method of Stamping

Article S-1 Contents and Method of Stamping

AIA/NAS NASM91528-2001 FSC 5355型塑料旋钮控制(圆的同中心的指示器可调控可触摸横条旋钮锁)

This specification provides a standard for the namfacture, perfomnance, rellability, inspection and procurement of a series of r e c t w table profile and contour milling machines having two, three, four and five axes of Numerically Controlled motion. and is not intended to l i m i t design advarices.

Knobs-Control, Plastic (Round, Concentric, Pointer, Spinner, Spinner Slip-Clutch, Bar, Tactile, Knob Lock Pointer, Slip-Clutch, and Knob Locks)

JB/T 5000.13-1998 重型机械通用技术条件.包装

　　本标准规定了重型机械产品的包装型式，包装要求和包装设计等。 　　本标准适用于重型机械产品的包装。凡图样及技术文件中无特殊要求时，均应符合本标准的规定。

The heavy mechanical general techniques and standards.Packing

KS B 6709-1993 站台车的种类及主要尺寸

이 규격은 스키드 등에 적재된 하물의 운반에 사용하는 유압 승강식 로 리프트형 플랫폼 트럭

Classification and dimensions of platform trucks

KS B 6710-1993 码垛车的种类及主要尺寸

이 규격은 팰릿 등에 적재된 하물의 운반에 사용하는 유압 승강식 로 리프트형 팰릿 트럭의

Classification and dimensions of pallet trucks

KS B 6711-1993 单元货物用垂直运输机

이 규격은 유닛 로드를 수직으로 반송하는 컨베이어(이하 수직 컨베이어라한다)에 대하여 규정

Vertical conveyors for unit loads

AIA/NAS NAS 1523-1992 (Rev. 3)固定器包装

USE OF OR RELUNCE UPON THIS DOCUMENT OR ANY NATIONAL AEROSPACE STANDARD IS ENTIRELY VOLUNTARY AIA DOES NOT QUALIFY SUPPLIERS OR :ERTiFY CONFORMANCE OF ITEMS PROCURED UNDER NATIONAL AEROSPACE STANDARDS. UTABILITY OF ITEMS FOR

Packing with Retainer (Rev. 3)

IPC TA-723-1991 外部贴装的技术评估

With sueh equipmnt, both reflowed and wave soldered SMCa can be removed fairly simply. Attaching a replacement part ia more complicated. Particularly with multileadeIdC s, it is difficult to align all the pins with the pads. huthermore, the amounot f new solder added to the joint is more critical. Alternatives include dispensing solder paste either through a syringe or pin-transfer technique, using pre-cut solder slugs, or using components with pre-tinned leadBs.e ll Labs has developed an interesting technique for tinning leads of small devices with a precise amount of solder.6

Technology Assessment of Surface Mounting

IPC TA-723 INTRO 外部贴装的技术评估

Because this document contains a broad range of technical information on surface mounting, we have provided some tips to help you use this document.

Technology Assessment of Surface Mounting

IPC TA-723 SECTION 4 元件封装

The first entry into the use of SET usually involves the conversion to the use of discrete surface mount devices (SAD’S), such as leafless chip resistors and capacitors. Article 4.2 provides a good summary of the criteria associated with the selection of SAD’s. The summary includes a discussion of general requirements, procurement specifications, chip standardization, component marking, solderability, some common assembly problems, and supplier selection factors.

Packaging Components

HB 4184-1988 尼龙系带捆扎枪技术条件

Technical conditions for Nylon band bundling-up machine

DIN 55201-2:1987 机床.机床托盘.公称直径大于100mm.B型

Machine tools; pallets for machine tools; nominal sizes over 800 mm; form B

JIS Z 9102:1987 管路系统识别标志

この規格は，工場・鉱山・学校・劇場・船舶・車両・航空保安施設その他において，配管系に設けたバルブの誤操作を防止するなどの安全を図ること，配管系の取扱いの適性化を図ることを目的に，配管に識別表示を行う場合のー般的事項にーフいて規定する。

Identification marking for piping systems

ISO 8991:1986 紧固件的标记制度

Specifies and describes a system for use in product standards; gives examples for hexagon head bolts, screws, and nuts, tapping screws, parallel pins, and washers.

Designation system for fasteners

DIN 55201-1:1985 机床.机床托盘.公称尺寸可达800mm.A型

This German Standard specifies dimensions and tolerances of workholding pallets for use with machining centres (horizontal and vertical spindle type), flexible manufacturing systems or other manufacturing systems to facilitate interchangeability. It deals with square pallets and rectangular pallets of lenght to width ratio of 1,25 up to 800 mm nominal size. Nominal sizes of 320,400,500, 630 and 800 mm are covered.#,,#

Machine tools; pallets for machine tools; nominal sizes up to 800 mm; form A