J11 滚动轴承 标准查询与下载
共找到 1481 条与 滚动轴承 相关的标准，共 99 页
本标准规定了外形尺寸符合GB/T 273.1-2011、GB/T 273.2-2006、GB/T 273.3-2015、GB/T 299-2008和GB/T 300-2008的一般用途球轴承、滚子轴承及其零件的补充技术要求，是对GB/T 307.1-2005、GB/T 307.3-2005 和GB/T 307.4-2012 的补充。 本标准适用于滚动轴承及其零件。
Rolling bearings.Supplementary specifications
- ICS
- 21.100.20
- CCS
- J11
- 发布
- 2017-01-09
- 实施
- 2017-07-01
本标准规定了滚动轴承用防锈油、清洗剂的清洁度和评定方法。 本标准适用于滚动轴承用防锈油、清洗剂的生产企业和使用企业对防锈油、清洗剂的清洁度测量及评定。
Rolling bearings.Cleanliness and its assessment methods of rust preventive oils and cleanser
- ICS
- 21.100.20
- CCS
- J11
- 发布
- 2017-01-09
- 实施
- 2017-07-01
Rolling Bearing Universal Joint Needle Roller Bearing
- ICS
- 21.100.20
- CCS
- J11
- 发布
- 2017-01-09
- 实施
- 2017-07-01
Standard for residual magnetism of rolling bearings and its evaluation method
- ICS
- 21.100.20
- CCS
- J11
- 发布
- 2017-01-09
- 实施
- 2017-07-01
Rolling bearings Roller bearings for rolling mills Part 2: Double and four-row tapered roller bearings
- ICS
- 21.100.20
- CCS
- J11
- 发布
- 2017-01-09
- 实施
- 2017-07-01
5.1 This test method is designed to produce bearing response data for material specifications, research and development, quality assurance, and structural design and analysis. The standard configuration for each procedure is very specific and is intended primarily for development of quantitative double- and single-shear bearing response data for material comparison and structural design. Procedures A and D, the double-shear configurations, with a single fastener loaded in shear and reacted by laminate tension or compression, are particularly recommended for basic material evaluation and comparison. Procedures B and C, the single-shear, single- or double-fastener configurations are more useful in evaluation of specific joint configurations, including fastener failure modes. The Procedure B specimen may be tested in either an unstabilized (no support fixture) or stabilized configuration. The unstabilized configuration is intended for tensile loading and the stabilized configuration is intended for compressive loading (although tensile loading is permitted). The Procedure C specimen is particularly well-suited for development of countersunk-fastener bearing strength data where a near-double-shear fastener rotational stiffness is desired. These Procedure B and C configurations have been extensively used in the development of design allowables data. 5.2 It is important to note that these four procedures, using the standard test configurations, will generally result in bearing strength mean values that are not of the same statistical population, and thus not in any way a “basic material property.” Note 2: Typically, Procedure D will yield slightly higher strengths than Procedure A (due to the finite edge distance, e, in Procedure A); while Procedure C will yield significantly higher strengths than Procedure B (due to the larger fastener rotation and higher peak bearing stress in Procedure B). For protruding head fasteners, Procedure D will typically yield somewhat higher results than Procedure C (due to both stress peaking and finite edge distance in Procedure C), and Procedures A and C yield roughly equivalent results. 5.3 It is also important to note that the parameter variations of the four procedures (tabulated in Section 4) provide flexibility in the conduct of the test, allowing adaptation of the test setup to a specific application. However, the flexibility of test parameters allowed by these variations makes meaningful comparison between datasets difficult if the datasets were not tested using the same procedure and identical test parameters. 5.4 General factors that influence the mechanical response of composite laminates and should therefore be reported include the following: material, methods of material preparation and lay-up, specimen stacking sequence, specimen preparation, specimen conditioning, environment of testing, specimen alignment and gripping, speed of testing, time at temperature, void content, and volume percent reinforcement. 5.5 Specific factors that influence the bearing response of composite laminates and should therefore be reported include not only the loading method (either Procedure A, B, or C) but t
Standard Test Method for Bearing Response of Polymer Matrix Composite Laminates
- ICS
- 83.120
- CCS
- J11
- 发布
- 2017
- 实施
Rolling bearings - Needle roller bearings - Part 3: Thrust washers
- ICS
- 21.100.20
- CCS
- J11
- 发布
- 2016-12
- 实施
Rolling bearings - Needle roller bearings - Part 2: Thrust needle roller and cage assemblies
- ICS
- 21.100.20
- CCS
- J11
- 发布
- 2016-12
- 实施
Rolling bearings - Safety regulations for dimensioning and operation of profiled rail guides with recirculating rolling elements; Text in German and English
- ICS
- 21.100.20
- CCS
- J11
- 发布
- 2016-12
- 实施
Rolling bearings - Needle roller bearings - Part 1: Needle roller and cage assemblies
- ICS
- 21.100.20
- CCS
- J11
- 发布
- 2016-12
- 实施
Plain bearings - Hydrostatic plain journal bearings with drainage grooves under steady-state conditions - Part 1: Calculation of oil-lubricated plain journal bearings with drainage grooves
- ICS
- 21.100.10
- CCS
- J11
- 发布
- 2016-09
- 实施
Plain bearings - Hydrodynamic plain thrust pad bearings under steady-state conditions - Part 2: Functions for the calculation of thrust pad bearings
- ICS
- 21.100.10
- CCS
- J11
- 发布
- 2016-09
- 实施
Rolling bearings - Briquets of grinding sludges
- ICS
- 21.100.20
- CCS
- J11
- 发布
- 2016-08-27
- 实施
- 2016-08-27
Rolling bearings -- Locknuts and locking devices
- ICS
- 21.060.20;21.060.30;21.100.20
- CCS
- J11
- 发布
- 2016-04-20
- 实施
Fastereners - Prevailing torque type steel nuts - Functional properties
- ICS
- 21.060.20
- CCS
- J11
- 发布
- 2016-03-10
- 实施
- 2016-03-10
Rolling bearings. Measuring methods for vibration. Radial ball bearings with cylindrical bore and outside surface
- ICS
- 21.100.20
- CCS
- J11
- 发布
- 2016-01-31
- 实施
- 2016-01-31
Rolling bearings. Measuring methods for vibration. Fundamentals
- ICS
- 21.100.20
- CCS
- J11
- 发布
- 2016-01-31
- 实施
- 2016-01-31
Rolling bearings. Needle roller bearings with drawn cup and without inner ring. Boundary dimensions, geometrical product specifications (GPS) and tolerance values
- ICS
- 21.100.20
- CCS
- J11
- 发布
- 2016-01-31
- 实施
- 2016-01-31
JB/T 5389的本部分规定了轧机用四列圆柱滚子轴承(以下简称轴承)的代号方法、主要结构类型、外形尺寸、技术要求、检测方法、检验规则、标志和防锈包装。 本部分适用于轧机用四列圆柱滚子轴承的生产、检验和验收。
Rolling bearings.Roller bearings for rolling mills.Part 1: Four row cylindrical roller bearings
- ICS
- 21.100.20
- CCS
- J11
- 发布
- 2016-01-15
- 实施
- 2016-06-01
本标准规定了公称内径d≤2 000 mm的单向和双向推力圆锥滚子轴承(以下简称轴承)的术语和定义、符号、代号方法、外形尺寸、技术要求、检测方法、检验规则、标志和防锈包装。 本标准适用于轴承的生产、检验和验收。
Rolling bearings.Thrust tapered roller bearings
- ICS
- 21.100.20
- CCS
- J11
- 发布
- 2016-01-15
- 实施
- 2016-06-01
