J11 滚动轴承 标准查询与下载
共找到 1481 条与 滚动轴承 相关的标准，共 99 页
Technical Specifications for Stamping Seats of Rolling Bearings and Insert Ball Bearings
- ICS
- 21.100.20
- CCS
- J11
- 发布
- 2023-12-29
- 实施
- 2024-07-01
Rolling bearings Thrust bearings for automotive steering knuckles
- ICS
- 21.100.20
- CCS
- J11
- 发布
- 2023-12-29
- 实施
- 2024-07-01
Test methods for hardness of rolling bearing parts
- ICS
- 21.100.20
- CCS
- J11
- 发布
- 2023-12-29
- 实施
- 2024-07-01
Technical Specifications for Rolling Bearings Thrust Spherical Roller Bearings
- ICS
- 21.100.20
- CCS
- J11
- 发布
- 2023-12-29
- 实施
- 2024-07-01
Rolling bearing accessories Set screws for spherical ball bearings
- ICS
- 21.100.20
- CCS
- J11
- 发布
- 2023-12-29
- 实施
- 2024-07-01
Technical specifications for black oxidation treatment of rolling bearing parts
- ICS
- 21.100.20
- CCS
- J11
- 发布
- 2023-12-29
- 实施
- 2024-07-01
Rolling bearing automotive constant velocity universal joint and its assembly
- ICS
- 21.100.20
- CCS
- J11
- 发布
- 2023-12-29
- 实施
- 2024-07-01
Bench test method for urban rail transit rolling bearings and metro vehicle axlebox bearings
- ICS
- CCS
- J11
- 发布
- 2021-12-29
- 实施
- 2022-03-01
Urban Rail Transit Rolling Bearings Subway Vehicle Axlebox Bearings
- ICS
- CCS
- J11
- 发布
- 2021-12-29
- 实施
- 2022-03-01
Bench test method for urban rail transit rolling bearings and metro vehicle axlebox bearings
- ICS
- CCS
- J11
- 发布
- 2021-12-29
- 实施
- 2022-03-01
Urban rail transit rolling bearing metro vehicle axle box bearing grease
- ICS
- CCS
- J11
- 发布
- 2021-12-29
- 实施
- 2022-03-01
Urban rail transit rolling bearing metro vehicle axle box bearing grease
- ICS
- CCS
- J11
- 发布
- 2021-12-29
- 实施
- 2022-03-01
Urban Rail Transit Rolling Bearings Subway Vehicle Axlebox Bearings
- ICS
- CCS
- J11
- 发布
- 2021-12-29
- 实施
- 2022-03-01
This document specifies the boundary dimensions, other relevant dimensions and the corresponding tolerances of accessories for sleeve type linear ball bearings which are specified in ISO 10285. This document applies to: — the following housings: — closed and adjustable flangeless
Rolling bearings - Accessories for sleeve type linear ball bearings - Part 1: Boundary dimensions, geometrical product specifications (GPS) and tolerances for series 1 and 3 (ISO 13012-1:2018)
- ICS
- 21.100.20
- CCS
- J11
- 发布
- 2021-07-00
- 实施
Rolling bearings - Explanatory notes on ISO 281 - Part 1: Basic dynamic load rating and basic rating life
- ICS
- 21.100.20
- CCS
- J11
- 发布
- 2021-05-00
- 实施
This document specifies a calculation method for oil-lubricated hydrodynamic plain bearings with complete separation of the thrust collar and tilting pad thrust bearing surfaces by a film of lubricant. This document applies to plain thrust bearings with tilting-type sliding blocks (tilting pads), where a wedge-shaped lubrication clearance gap is automatically formed during operation. The ratio of width to length of one pad can be varied in the range B/L = 0,5 to 2. This document is not applicable to heavily loaded tilting pad thrust bearings. NOTE Equivalent calculation procedures exist that enable operating conditions to be estimated and checked against acceptable conditions. The use of them is equally admissible.
Plain bearings - Hydrodynamic plain tilting pad thrust bearings under steady-state conditions - Part 1: Calculation of tilting pad thrust bearings
- ICS
- 21.100.10
- CCS
- J11
- 发布
- 2021-04-00
- 实施
This document specifies the dimensions and tolerances for inserted thermoplastic bushes used as plain bearings with or without lubrication grooves in accordance with ISO 12128. These thermoplastic bushes are dimensionally exchangeable to wrapped bushes according to ISO 3547-1. This document is not applicable to reinforced plastics.
Plain bearings - Thermoplastic bushes - Dimensions and tolerances
- ICS
- 21.100.10
- CCS
- J11
- 发布
- 2021-03-00
- 实施
Rolling bearings -- Boundary dimensions, geometrical product specifications (GPS) and tolerance values of needle roller bearings -- Part 5: Track rollers
- ICS
- 21.100.20
- CCS
- J11
- 发布
- 2021-02-22
- 实施
Rolling bearings -- Boundary dimensions, geometrical product specifications (GPS) and tolerance values of needle roller bearings -- Part 1: Machined rings
- ICS
- 21.100.20
- CCS
- J11
- 发布
- 2021-02-22
- 实施
Rolling bearings -- Damage and failures -- Terms, characteristics and causes
- ICS
- 21.100.20
- CCS
- J11
- 发布
- 2021-02-22
- 实施
