J21 润滑与润滑装置 标准查询与下载
共找到 168 条与 润滑与润滑装置 相关的标准，共 12 页
JB/T 8801.1-1998 本标准等到效采用德国代立蒙（Delimon）公司的试验规范。 本标准规定了电动润滑泵 40MPa 的型号，基本参数与外形尺，技术要求，试验方法，检验规则和标志、包装、运输、贮存。 本标准适用于向集中润滑系统供送润滑脂，公称压力为 40MPa 的电动润滑泵。 （注： 自本标准实施之起，JB/ZQ 4582-86《电动润滑泵（40MPa）》、JB/ZQ 4096-88《电动润滑泵技术条件（40MPa）》作废。）
Electrical lubrication pumps 40 MPa
- ICS
- 21.260
- CCS
- J21
- 发布
- 1998-09-30
- 实施
- 1998-12-01
本标准规定了微型电动润滑泵的基本参数、外形及安装尺寸、技术要求、试验方法、验收规则和标志、包装、运输及贮存等。 本标准适用于金属切削机床及锻压机械润滑系统，其他机械的润滑系统亦可参照使用。
Component of machines' lubrication system Minitype electric lubricant pump
- ICS
- 21.260
- CCS
- J21
- 发布
- 1997-08-18
- 实施
- 1998-01-01
本标准规定了块式递进式分配器的基本参数及安装尺寸、技术要求、试验方法和验收规则和标志、包装、运输及贮存等。 本标准适用于机床润滑系统，其他机械的润滑系统亦可参照使用。
Component of machines' lubrication system Block type progressive plunger metering devices
- ICS
- 21.260
- CCS
- J21
- 发布
- 1997-08-18
- 实施
- 1998-01-01
本标准规定了稀油润滑装置的型式、基本参数与尺寸。 本标准适用于冶炼、轧制、矿山、电力、石化、建材等机械设备的稀油循环润滑系统的稀油润滑装置。
Diluted oil lubrication unit Type, basic parameters and dimensions
- ICS
- 21.260
- CCS
- J21
- 发布
- 1997-03-04
- 实施
- 1997-10-01
本标准规定了二位四通换向阀40MPa的型号、基本参数与外形尺寸、技术要求、试验方法、检验规则和标志、标签、包装。 本标准适用于公称压力为40MPa的双线干油集中润滑系统中的二位四通换向阀。
Two-position four-way reversing valves 40MPa
- ICS
- 21.260
- CCS
- J21
- 发布
- 1996-09-03
- 实施
- 1997-07-01
本标准规定了递进分配器16MPa的型号、基本参数与外形尺寸、技术要求、试验方法、检验规则和标志、标签、包装。 本标准适用于公称压力为16MPa的单线递进式干油集中润滑系统中的递进分配器。
Progressive plunger metering devices 40MPa
- ICS
- 21.260
- CCS
- J21
- 发布
- 1996-09-03
- 实施
- 1997-07-01
本标准规定了压差开关40MPa的型号、基本参数与外形尺寸、技术要求、试验方法、检验规则和标志、标签、包装。 本标准适用于公称压力为40MPa的双线干油集中润滑系统中的压差开关。
Air differential pressure switches 40MPa
- ICS
- 21.260
- CCS
- J21
- 发布
- 1996-09-03
- 实施
- 1997-07-01
本标准规定了双线分配器40MPa的型号、基本参数与外形尺寸、技术要求、试验方法、检验规则和标志、标签、包装。 本标准适用于公称压力为40MPa的双线干油集中润滑系统中的双线分配器。
Two-line metering devices 40MPa
- ICS
- 21.260
- CCS
- J21
- 发布
- 1996-09-03
- 实施
- 1997-07-01
本标准规定了定流向摆线转子润滑泵的型号标志、技术要求、试验方法、数据整理、检验规则及标志、包装与贮存。 本标准适用于以精制矿物油为工作介质的润滑泵。
Permanent flow cycloid rotor lubricant pump
- ICS
- 21.260
- CCS
- J21
- 发布
- 1996-04-22
- 实施
- 1996-07-01
本标准规定了接头式压注油杯的型式与尺寸。 本标准适用于各种机械设备及汽车、船舶等用的润滑脂压注油杯。
Angle hydraulic grease nipples
- ICS
- 21.260
- CCS
- J21
- 发布
- 1996-04-14
- 实施
- 1996-04-14
本标准规定了直通式压注油杯的型式与尺寸。 本标准适用于各种机械设备及汽车、船舶等用的润滑脂压注油杯。
Straight hydraulic grease nipples
- ICS
- 21.260
- CCS
- J21
- 发布
- 1996-04-14
- 实施
- 1996-04-14
本标准规定了油杯的技术要求、试验方法、检验规则、标志与包装。 本标准适用于各种油杯。
Grease nipples and lubricating cups technical specification
- ICS
- 21.260
- CCS
- J21
- 发布
- 1996-04-14
- 实施
- 1996-04-14
本标准规定了针阀式注油杯的型式与尺寸。 本标准适用于机械设备上机械油注油杯。
Drip-feed type lubricating cups
- ICS
- 21.260
- CCS
- J21
- 发布
- 1996-04-14
- 实施
- 1996-04-14
本标准规定了弹簧盖油杯的型式与尺寸。 本标准适用于机械设备上机械油润滑油杯。
Spring cap type lubricating cups
- ICS
- 21.260
- CCS
- J21
- 发布
- 1996-04-14
- 实施
- 1996-04-14
本标准规定了压配式压注油杯的型式与尺寸。 本标准适用于机械设备上机械油压注油杯。
Push-fit type grease nipples
- ICS
- 21.260
- CCS
- J21
- 发布
- 1996-04-14
- 实施
- 1996-04-14
本标准规定了旋盖式油杯的型式与尺寸。 本标准适用于机械设备上润滑脂压注油杯。
Screwing cap type lubricating cups
- ICS
- 21.260
- CCS
- J21
- 发布
- 1996-04-14
- 实施
- 1996-04-14
1.1 This specification covers automatic or continuously self-cleaning automatic strainers, or both, for use in fuel and lubrication oil systems. The strainer is designed to operate under positive pressure (discharge side of the pump). Strainers manufactured to this specification are suitable for use in any marine environment. 1.2 It is not the intent of this document to redefine existing filtration standards. The intent is to provide sound guidelines for purchasers and designers of lube oil and fuel oil systems. Nominal micron requirements and filter efficiencies shall be as agreed upon by the purchaser and manufacturer and stated in the purchase order document.
Standard Specification for Fabricated or Cast Automatic Self-Cleaning, Fuel Oil and Lubricating Oil Strainers
- ICS
- 21.260 (Lubrication systems)
- CCS
- J21
- 发布
- 1994
- 实施
1.1 This specification covers automatic or continuously self-cleaning automatic strainers, or both, for use in fuel and lubrication oil systems. The strainer is designed to operate under positive pressure (discharge side of the pump). Strainers manufactured to this specification are suitable for use in any marine environment.1.2 It is not the intent of this document to redefine existing filtration standards. The intent is to provide sound guidelines for purchasers and designers of lube oil and fuel oil systems. Nominal micron requirements and filter efficiencies shall be as agreed upon by the purchaser and manufacturer and stated in the purchase order document.
Standard Specification for Fabricated or Cast Automatic Self-Cleaning, Fuel Oil and Lubricating Oil Strainers
- ICS
- 21.260 (Lubrication systems)
- CCS
- J21
- 发布
- 1994
- 实施
1.1 This specification covers automatic or continuously self-cleaning automatic strainers, or both, for use in fuel and lubrication oil systems. The strainer is designed to operate under positive pressure (discharge side of the pump). Strainers manufactured to this specification are suitable for use in any marine environment. 1.2 It is not the intent of this document to redefine existing filtration standards. The intent is to provide sound guidelines for purchasers and designers of lube oil and fuel oil systems. Nominal micron requirements and filter efficiencies shall be as agreed upon by the purchaser and manufacturer and stated in the purchase order document.
Standard Specification for Fabricated or Cast Automatic Self-Cleaning, Fuel Oil and Lubricating Oil Strainers
- ICS
- CCS
- J21
- 发布
- 1994
- 实施
