共找到 49 条与 冷加工工艺 相关的标准,共 4 页
Fonds bombés - Fonds à grand rayon de carre (GRC) - Dimensions.
IPC Standards and Publications are designed to serve the public interest through
Resin Flow of"No Flow" Prepreg Revision B
IPC Standards and Publications are designed to serve the public interest through
Resin Flow Percent of Prepreg Revision D
This standard establishes requirements and other considerations
Flammability of Prepreg and Thin Laminate Revision D
This document covers guidelines for selecting electrically conductive adhesives for use in assembly of components to printed circuit boards (PCB) or similar wiring interconnect systems. The focus is on the use of adhesives as solder alternatives. The process discussion attempts to stay within the bounds of the existing solder assembly infrastructure as much as possible. Both major types of adhesives, isotropic (conducting equally in all directions) and anisotropic (unidirectional conductivity), are covered. The two major divisions of polymer adhesives, thermosets and thermoplastics, are described.
Volatile Content of Prepreg; Revision C - December 1994
This International Standard relates to grid systems for printed circuits to ensure compatibility between the printed circuits and parts to be mounted on them at the intersections of the grid.
Resin Content of Prepreg, by Burn-Off; Revision B - December 1994
This guide is intended to be used by circuit designers, packaging engineers, printed board fabricators, and procurement personnel so that all may have a common understanding of each other’s area.
Resin Content of Prepreg, by Treated Weight; Revision C - December 1994
This standard establishes requirements and other considerations
Treated Weight of Prepreg
Punching and stamping. Codification for designating material perforations.
Punching and stamping. Aperture and pitch of perforated materiel with round holes and square holes.
This standard provides the principles and details for declarations necessary between members of a supply chain. Although this standard contains only generic information regarding trading partners, when combined with a specific sectional standard, the entire document set is used to define and maintain the declaration type information. The requirements pertain to both hard copy and electronic data descriptions. This standard provides for the creation of a record that will serve as a commitment between trading partners and may be used to establish due diligence in any dispute in third-party litigation.
Prepreg Scaled Flow Testing Revision A
Requirements for guns complying with BS 6742-1.
Electrostatic painting and finishing equipment using flammable materials - Electrostatic painting and finishing equipment using flammable materials - Specification for selection, installation and use of hand-held flock spray guns (energy limit of 0,24 mJ
Punching and stamping. Burr on blanked or punched metallic parts. Maximum allowable burr height and measuring method.
The standard describes the testing of metallic abrasives by centrifugal blasting.
Testing the wear and effectiveness of metallic abrasives by centrifugal blasting
This Standard covers dimensioning and tolerancing of electronic packaging as it relates to printed boards and the assembly of printed boards. The concepts defined in this Standard are derived from ASME Y14.5” 1994. Printed boards have such wide applications that there may be times where this standard does not address a specific case. In those cases, the user is referred to ASME Y14.5M 1994 for use of additional dimensioning and tolerancing concepts.
Gel Time for Prepreg Materials; Revision A - April 1986
Cold bending of flat steel products; calculated compensating values
Blasting; terms, classification of blasting techniques
Blasting; terms, classification of blasting techniques
Testing of abrasives; test cabin for pressure-type blastingEssais des abrasifs; cabine d'essai pour projection comprimé
Testing of abrasives; test cabin for pressure-type blasting
この規格は,鉄鋼研削仕上げ面(円筒研削,内面研削及び平面研削の仕上げ面)の研削しろが特に指定されていないときの,研削しろについて規定する。2.用語この規格で用いる用語の意味は,次による。 (1)研削しろ 工作物が所定の寸法・形状及び表面粗さに経済的に研削仕上げされるように,その前加工において工作物に残しておく余肉の寸法。(2)前加工 工作物を.所定の研削しろを有する状態まで切削する作業。
Removal in grindings
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号