J51 机床零部件 标准查询与下载

JB/T 2886-2008 机床梯形丝杠、螺母.技术条件

本标准规定了机床梯形丝杠、螺母的术语和定义、精度要求及检验方法。 本标准适用于机床传动及定位用，牙型角符合GB/T 5796.1，螺距与直径符合GB/T 57962的单线梯形丝杠、螺母。其他非标准牙型角的梯形丝杠、螺母亦可参照执行。

Trapezoid thread screw and nut for machine tools.Specincations

ISO 5415:2007 带7/24外锥度和莫氏内锥度的缩径套筒和连接螺钉

This International Standard specifies the dimensions of reduction sleeves with 7/24 external taper No. 30-40-45-50 and 60 and Morse internal taper No. 1 to 6 (Morse taper No. 4, 5 and 6 being either with positive drive, see Figure 2, or without positive drive, see Figure 1). These sleeves permit driving of tools with Morse taper shanks with tapped holes with the aid of an internal screw. The form of this screw and its fixation in the sleeve are left to the manufacturer's discretion. 7/24 tapers are in accordance with ISO 297. Morse tapers are in accordance with ISO 296 and ISO 5413.

Reduction sleeves with 7/24 external and Morse internal taper and incorporated screw

JB/T 10791.1-2007 带刀具自动交换装置的刀库.第1部分:技术条件

JB/T 10791的本部分规定了带刀具自动交换装置的刀库的设计、制造和验收要求。 本部分适用于加工中心用带刀具自动交换装置的盘式刀库、链式刀库和箱式刀库。不带刀具自动交换装置的刀库或其他型式的刀库可参照本部分执行。

Tool storage with automatic tool changer.Part 1: Specifications

JB/T 6105-2007 数控机床液压泵站 技术条件

本标准规定了数控机床液压泵站（以下简称泵站）的基本参数和主要性能指标以及设计、制造、安装和使用（包括有关组件）的一般要求。 本标准适用于以液压油为工作介质的泵站。

Specifications for hydraulic pump station in numerical control machine tools

KS B ISO 5170:2007 机床.润滑系统

이 규격은 공작기계의 각종 윤활 시스템의 분류, 시스템 요소에 관한 시방, 제어 및 감시

Machine tools-Lubrication systems

KS B ISO 5169:2007 机床.润滑指示图的标识方法

이 규격은 윤활 지시도의 표시 방법에 관한 것으로 공작 기계 제조자가 제공하여 사용자가 따

Machine tools-Presentation of lubrication instructions

KS B ISO 2727:2007 组合机床通用部件.动力箱

이 규격은 모듈 유닛으로 구성하는 특수 목적 기계에 사용되는 주축대의 호환성과 관련된 치수

Modular units for machine tool construction-Headstocks

DLA A-A-55563 C-2007 金属插件导轨电卡架的一般要求

This Commercial Item Description (CID) covers the general requirements for a family of metal card guides (hereafter referred to as card holders) intended for use to guide and hold circuit card assemblies into their installed positions.

HOLDER, ELECTRICAL CARD, METAL CARD GUIDE, GENERAL REQUIREMENTS FOR

NF E22-201-3*NF ISO 3408-3:2006 滚珠丝杠.第3部分:验收条件和验收检验

Ball screws - Part 3 : acceptance conditions and acceptance tests.

JB/T 7175.2-2006 滚动直线导轨副 第2部分:参数

JB/T 7175的本部分规定了滚动直线导轨副的参数。 本部分适用于以滚珠为滚动体的滚动直线导轨副。其他滚动体的直线导轨副亦可参照使用。

Rolling linear guide Part 2: Parameters

JB/T 7175.4-2006 滚动直线导轨副 第4部分:验收技术条件

JB/T 7175的本部分规定了两滚道型、四滚道型滚动直线导轨副的精度等要求及检验方法。 本部分适用于以滚珠为滚动体的滚动直线导轨副。其他滚动体的直线导轨副亦可参照使用。

Rolling linear guide Part 4: Acceptance specifications

NF E22-201-5*NF ISO 3408-5:2006 滚珠丝杠.第5部分:静态和动态轴负荷额定值和工作寿命

Ball screws - Part 5 : static and dynamic axial load ratings and operational life.

DIN 69893-5:2006 带平端面的锥形空心柄.第5部分:E型锥形空心柄.尺寸

The document specifies the dimensions for hollow taper shanks with flat contact surface which can be used on high speed work spindles machine tools (e. g. drilling, milling and grinding machines).#,,#

Hollow taper shanks with flat contact surface - Part 5: Hollow taper shanks type E; Dimensions

BS ISO 3408-1:2006 滚珠丝杠.词汇、命名和符号

This part of ISO 3408 establishes the vocabulary for ball screws (see Figure 1) and specifies their designation.

Ball screws - Vocabulary and designation

BS ISO 3408-5:2006 滚珠丝杠.静态和动态轴额定负荷和工作寿命

This part of ISO 3408 specifies the calculation schemes for static and dynamic load ratings, and operational life, in order to obtain comparable values for the design and use of ball screws. NOTE The calculations have been based primarily on publications by Prof. G. Lundberg and A. Palmgren Acta Politechnica, mech. Eng. series Vol. I, No. 3, Stockholm, Sweden. Part 7, 1947. This part of ISO 3408 is applicable under the following preconditions: — elastic deformation of ball and balltrack; — hardness of balltrack basically exceeds a minimum of HRC 58; — conformity/rs andfm> 0,5; — the quality of steel of which the ball screw is made is equivalent to that of ball bearing steel or similar steel alloys; — optimum lubrification is always provided.

Ball screws - Static and dynamic axial load ratings and operational life

JB/T 10610-2006 牵引电磁铁

本标准规定了牵引电磁铁的分类、技术要求、试验方法、检验规则等。 本标准适用于牵引电磁铁（以下简称电磁铁）。电磁铁主要用于交流5OHz、额定电压至380V，直流电压至220V电路中，作为机械设备及自动化系统远距离操作控制的动力装置。

Tractive electro-magnets

BS ISO 3408-3:2006 滚珠丝杠.验收条件和验收检验

This part of ISO 3408 specifies the technical acceptance conditions for ball screws (see Figure 1) and, in particular, the respective permissible deviations for the acceptance tests. NOTE The actual design need not necessarily correspond to that shown in Figure 1. The respective tests required will be agreed upon between the manufacturer and user.

Ball screws - Acceptance conditions and acceptance tests

ISO 3408-1:2006 滚珠丝杠.第1部分:词汇、名称与符号

This part of ISO 3408 establishes the vocabulary for ball screws (see Figure 1) and specifies their designation.

Ball screws - Part 1: Vocabulary and designation

ISO 3408-4:2006 滚珠丝杠.第4部分:静态轴向刚度

This part of ISO 3408 sets forth terms and mathematical relations relevant to the determination of the static axial rigidity of the ball screw.

Ball screws - Part 4: Static axial rigidity

ISO 3408-5:2006 滚珠丝杠.第5部分:静态和动态轴负荷额定值和工作寿命

This part of ISO 3408 specifies the calculation schemes for static and dynamic load ratings, and operational life, in order to obtain comparable values for the design and use of ball screws. NOTE The calculations have been based primarily on publications by Prof. G. Lundberg and A. Palmgren Acta Politechnica, mech. Eng. series Vol. I, No. 3, Stockholm, Sweden. Part 7, 1947. This part of ISO 3408 is applicable under the following preconditions: — elastic deformation of ball and balltrack; — hardness of balltrack basically exceeds a minimum of HRC 58; — conformity/rs andfm> 0,5; — the quality of steel of which the ball screw is made is equivalent to that of ball bearing steel or similar steel alloys; — optimum lubrification is always provided.

Ball screws - Part 5: Static and dynamic axial load ratings and operational life