J58 组合机床 标准查询与下载

KS B ISO 10791-2:2007 机械加工中心试验条件.第2部分:立式或带有垂直主回转轴万能轴头(垂直轴.Z)机床的几何精度试验

이 규격은 KS B ISO 230-1을 기초로 하여 수직형(즉, 수직 Z축) 머시닝 센터(

Test conditions for machining centres-Part 2:Geometric tests for machines with vertical spindle or universal heads with vertical primary rotary axis(vertical Z-axis)

JB/T 1534-2006 组合机床 通用技术条件

本标准规定了组合机床（包括组合机床自动线、组合机床通用部件，以下简称机床）基本的、共同性的技术要求。 本标准适用于机床的设计、制造、检验与验收。

Special purpose machines general specifications

JB/T 7448.2-2006 小型组合机床 第2部分:技术条件

JB/T 7448的本部分规定了小型组合机床（包括小型组合机床自动线、小型组合机床通用部件，以下简称机床）制造和验收的技术要求。 本部分适用于机床的设计、制造、检验与验收。

Miniature modular machines Part 2: Specifications

JB/T 7448.1-2006 小型组合机床 第1部分:精度检验

JB/T 7448的本部分规定了小型组合机床的几何精度和工作精度检验的要求及方法。 本部分适用于名义尺寸至250mm的主轴部件组成的回转工作台式、移动工作台式和固定工作台式小型组合机床（以下简称机床）。

Miniature modular machines Part 1: Testing of the accuracy

ISO 10791-6:1998/Cor 1:2004 加工中心检验条件.第6部分:进给率、速度和插补精度.技术勘误1

This is Technical Corrigendum 1 to ISO 10791-6-1998 (Test conditions for machining centres — Part 6: Accuracy of feeds, speeds and interpolations)

Test conditions for machining centres - Part 6: Accuracy of feeds, speeds and interpolations; Technical Corrigendum 1

BS ISO 10791-8:2001 加工中心的试验条件.三坐标平面仿形加工性能的估计

This part of ISO 10791 specifies a method of checking the contouring performance of machining centres (or numerically controlled milling machines, etc., where applicable) by conducting circular tests in the three coordinate planes (XY, YZ and XZ) and by evaluating the radial deviation, F, and circular deviation, G, in accordance with ISO 230-4. NOTE Measurements of circular movements can be carried out by different methods as described in 6.6 of ISO 230-1:1996. These methods consist of using a rotating one-dimensional probe and a test mandrel, a circular masterpiece and a two-dimensional probe, or a telescoping ball bar. Other test methods may be applied if the accuracy of the equipment is the same as (or better than) the accuracy of the methods described. Influences of typical machine deviations on circular paths are shown in annex B of ISO 230-4:1996. The purpose of the checks by circular tests described in this part of ISO 10791 is to verify the circular movement — only in one position per coordinate plane of the machine, — at only one feed rate, and — to repeat the test once in the opposite contouring direction. The purpose of this part of ISO 10791 is not to provide a means of analysing the causes for the measured circular deviations, but to offer the user a method for periodic checking of the machine tool. It is recommended to carry out the tests of this part of ISO 10791 once the machine tool has satisfactorily undergone the acceptance tests and to use these results as a basis for comparison when carrying out periodic checks. Therefore, acceptable deviations from the initial results shall be decided by the user. If the tests are used for machine acceptance purposes, the supplier/manufacturer and the user shall agree on specific diameters, feed rates and tolerances for the tests. NOTE ISO 10791-6, which deals with the accuracy of feeds, speeds and interpolations, also includes as test K4 a circular test. Here, the purpose is to check the mutual behaviour of two linear axes (generally X and Y) at two defined feed rates for one defined diameter. This is more or less a diagnostic test with respect to the circular interpolation, whereas the circular tests of this part of ISO 10791 give information on the overall contouring performance of the machine.

Test conditions for machining centres - Evaluation of contouring performance in the three coordinate planes

BS ISO 10791-2:2001 加工中心的试验条件.带垂直主轴或(垂直Z-轴)万用头的机床的几何试验

This part of ISO 10791 specifies, with reference to ISO 230-1, the geometric tests for machining centres (or numerically controlled milling machines, boring machines, etc., where applicable) with vertical spindle (that is vertical Z-axis). This part of ISO 10791 applies to machining centres having basically three numerically controlled axes, that is three linear axes (X, Y and Z) of up to 2 000 mm length, but also refers to supplementary motions, such as rotary axes (A', B' and C'), those of rams, quill, or universal heads. Motions other than those mentioned are considered as special features and the relevant tests are not included in this part of ISO 10791. This part of ISO 10791 describes geometric tests for optional horizontal spindles as well as for two possible types of universal heads in the following annexes: — annex A: optional horizontal spindles (tests AG1 to AG6); — annex B: rotary heads, with one numerically controlled rotary axis (tests BG1 and BG2); — annex C: swivel heads, with two numerically controlled rotary axes perpendicular to each other (tests CG1 to CG7). This part of ISO 10791 deals only with the verification of the accuracy of the machine. It does not apply to the testing of the machine operation, which should be checked separately. Some tests concerning the performance of the machine operating under no-load or finishing conditions are included in other parts of ISO 10791.

Test conditions for machining centres - Geometric tests for machines with vertical spindle or universal heads with vertical primary rotary axis (vertical Z-axis)

BS ISO 10791-9:2001 加工中心的试验条件.刀具更换和托架更换所用时间的估计

This part of ISO 10791 specifies certain standard test conditions for assessing the conventional length of the operating times spent by the machine to carry out different metal cutting functions. It considers two types of operating times, namely those taken by the functions of: — automatic tool change (see clause 5); — automatic pallet change (see clause 6). The purpose of the methods described in this part of ISO 10791 is to permit the comparison of the performance of different machining centres of similar size and features. The data obtained may also be used to establish conventional change times in technical literature in a uniform and comparable way. It is also possible to check them on a machine, both when it is new and during its working life.

Test conditions for machining centres - Evaluation of the operating times of tool change and pallet change

ISO 10791-8:2001 加工中心试验条件 第8部分：3个协调平面的轮廓性能的评价

This part of ISO 10791 specifies a method of checking the contouring performance of machining centres (or numerically controlled milling machines, etc., where applicable) by conducting circular tests in the three coordinate planes (XY, YZ and XZ) and by evaluating the radial deviation, F, and circular deviation, G, in accordance with ISO 230-4. NOTE Measurements of circular movements can be carried out by different methods as described in 6.6 of ISO 230-1:1996. These methods consist of using a rotating one-dimensional probe and a test mandrel, a circular masterpiece and a two-dimensional probe, or a telescoping ball bar. Other test methods may be applied if the accuracy of the equipment is the same as (or better than) the accuracy of the methods described. Influences of typical machine deviations on circular paths are shown in annex B of ISO 230-4:1996. The purpose of the checks by circular tests described in this part of ISO 10791 is to verify the circular movement — only in one position per coordinate plane of the machine, — at only one feed rate, and — to repeat the test once in the opposite contouring direction. The purpose of this part of ISO 10791 is not to provide a means of analysing the causes for the measured circular deviations, but to offer the user a method for periodic checking of the machine tool. It is recommended to carry out the tests of this part of ISO 10791 once the machine tool has satisfactorily undergone the acceptance tests and to use these results as a basis for comparison when carrying out periodic checks. Therefore, acceptable deviations from the initial results shall be decided by the user. If the tests are used for machine acceptance purposes, the supplier/manufacturer and the user shall agree oh specific diameters, feed rates and tolerances for the tests. NOTE ISO 10791-6, which deals with the accuracy of feeds, speeds and interpolations, also includes as test K4 a circular test. Here, the purpose is to check the mutual behaviour of two linear axes (generally X and Y) at two defined feed rates for one defined diameter. This is more or less a diagnostic test with respect to the circular interpolation, whereas the circular tests of this part of ISO 10791 give information on the overall contouring performance of the machine.

Test conditions for machining centres - Part 8: Evaluation of the contouring performance in the three coordinate planes

ISO 10791-2:2001 加工中心试验条件 第2部分：立式或带有垂直主回转轴万能轴头的机床的几何精度试验（垂直轴 Z）

This part of ISO 10791 specifies, with reference to ISO 230-1, the geometric tests for machining centres (or numerically controlled milling machines, boring machines, etc., where applicable) with vertical spindle (that is vertical Z-axis). This part of ISO 10791 applies to machining centres having basically three numerically controlled axes, that is three linear axes (X, Y and Z) of up to 2 000 mm length, but also refers to supplementary motions, such as rotary axes (A', B' and C'), those of rams, quill, or universal heads. Motions other than those mentioned are considered as special features and the relevant tests are not included in this part of ISO 10791. This part of ISO 10791 describes geometric tests for optional horizontal spindles as well as for two possible types of universal heads in the following annexes: — annex A: optional horizontal spindles (tests AG1 to AG6); — annex B: rotary heads, with one numerically controlled rotary axis (tests BG1 and BG2); — annex C: swivel heads, with two numerically controlled rotary axes perpendicular to each other (tests CG1 to CG7). This part of ISO 10791 deals only with the verification of the accuracy of the machine. It does not apply to the testing of the machine operation, which should be checked separately. Some tests concerning the performance of the machine operating under no-load or finishing conditions are included in other parts of ISO 10791.

Test conditions for machining centres - Part 2: Geometric tests for machines with vertical spindle or universal heads with vertical primary rotary axis (vertical Z-axis)

ISO 10791-9:2001 加工中心检验条件 第9部分：刀具交换和托板交换操作时间的评价

GB/T 18400的本部分规定了加工中心(以下简称机床)在确立的标准检验条件下，执行不同金属 切削功能时所需常规操作时间的评定方法。 本部分适用于下列两种功能操作时间的评定： ——刀具自动交换(见第5章)； ——托板自动交换(见第6章)。 GB／T 18400的本部分所述方法适用于规格和特征相似的不同机床之间性能的比较。 用统一和比较方式所获得的数据也适用于技术报告中常规交换时间的确立，以及对新机床和处于 寿命期间的机床进行检验。

Test conditons for machining centres - Part 9: Evaluation of the operating times of tool change and pallet change

DIN ISO 10791-1:2001 机床.加工中心的检验条件.第1部分:卧式和带附加主轴头几何精度检验(水平Z轴)(ISO 10791-1:1999)

Machine tools - Test conditions for machining centres - Part 1: Geometric tests for machines with horizontal spindle and with accessory heads (horizontal Z-axis) ( ISO 10791-1:1999)

DIN ISO 10791-7:2001 机床.加工中心的试验条件.第7部分:精加工试件的精度(ISO 10791-7:1998)

Machine tools - Test conditions for machining centres - Part 7: Accuracy of a finished test piece (ISO 10791-7:1998)

DIN ISO 10791-3:2001 机床.加工中心的试验条件.第3部分:分度或连续的万能主轴头机床的几何精度试验(垂直Z轴)(ISO 10791-3:1998)

The document specifies with reference to ISO 230-1 different geometric tests for machining centres with integral indexable or continuous universal heads (vertical Z-axis) and is applicable for machining centres having basically four numerically controlled axes.

Machine tools - Test conditions of machining centres - Part 3: Geometric tests for machines with integral indexable or continuous universal heads (vertical Z-axis) (ISO 10791-3:1998)

DIN ISO 10791-4:2001 机床.加工中心的检验条件.第4部分:线性和回转轴线的定位精度和重复定位精度(ISO 10791-4:1998)

The document specifies, with reference to ISO 230-2, the tolerances which apply to the positioning tests for linear axes, up to 2000 mm in length and rotary axes of machining centres.#,,#

Machine tools - Test conditions for machining centres - Part 4: Accuracy and repeatability of positioning of linear and rotary axes (ISO 10791-4:1998)

JB/T 9883-1999 组合机床.立柱.精度检验

　　本标准规定了组合机床立柱的几何精度要求和检验方法。 　 本标准适用于组合机床及其自动线的立柱。

Combined machine tool Columns Accuracy inspection

JB/T 9892.1-1999 组合机床.动力箱.精度检验

　　本标准规定了组合机床动力箱的几何精度要求和检验方法。 　 本标准适用于组合机床及其自动线的动力箱。

Combined machine tool Power case Accuracy inspection

JB/T 9892.2-1999 组合机床.动力箱.技术条件

　　本标准规定了组合机床动力箱的制造和验收方法。 　 本标准适用于组合机床动力箱。

Combined machine tool Power case Technical conditions

JB/T 9891-1999 组合机床.多轴箱.技术条件

　　本标准规定了组成合机床多轴箱的制造和验收要求。 　 本标准适用组成合机床多轴箱。

Combined machine tool Multi-spindle heads Technical conditions

JB/T 4316.1-1999 直齿端齿盘.系列参数和尺寸

本标准仅规定直齿端齿盘的系列参数和互换性尺寸。 本标准适用于金属切削机床圆分度用的齿盘。

Straight-tooth end-toothed disc Parameters and dimensions of series