J92 机体与运动件 标准查询与下载
共找到 368 条与 机体与运动件 相关的标准，共 25 页
This part of ISO 6621 specifies the general characteristics of piston rings for reciprocating internal combustion engines for road vehicles and other applications (the individual dimensional criteria for these rings are given in the relevant International Standards). It also provides a system for ring coding, designation, and marking. It is applicable to all such rings of a nominal diameter from 30 mm up to and including 200 mm.
Internal combustion engines - Piston rings - Part 4: General specifications
- ICS
- 43.060.10
- CCS
- J92
- 发布
- 2015-03
- 实施
本标准规定了通用小型汽油机用排气催化净化器的技术要求、试验方法及标志、包装、运输和贮存。本标准适用于通用小型汽油机用排气催化净化器(以下简称催化器)。
Catalytic converters of general utility small gasoline engines.Technical requirements and testing methods
- ICS
- 27.020
- CCS
- J92
- 发布
- 2014-07-09
- 实施
- 2014-11-01
本标准规定了往复式内燃机缸套活塞环组件的拉伤试验方法及试验结果的判定。 本标准适用于道路车辆、船舶、农用拖拉机和林业机械、工程机械、发电机组、排灌机械用的往复式内燃机（以下简称内燃机）的缸套活塞环组件。其他用途往复式内燃机的缸套活塞环组件也可参照采用。
Reciprocating internal combustion engines.Cylinder liner-piston-ring assemblies.Scoring test methods
- ICS
- 27.020
- CCS
- J92
- 发布
- 2014-05-06
- 实施
- 2014-10-01
JB/T 5082的本部分规定了激光淬火气缸套的术语和定义、技术要求、检验方法与检验规则、标志、包装、运输和贮存。 本部分适用于气缸套直径小于或等于200 mm的往复式内燃机激光淬火气缸套（以下简称气缸套）。
Internal combustion engines.Cylinder liners.Part 6: Technology specifications of laser-quench cylinder liners
- ICS
- 27.020
- CCS
- J92
- 发布
- 2014-05-06
- 实施
- 2014-10-01
本标准规定了往复式内燃机大功率柴油机整体连续纤维锻钢曲轴的技术要求、检验方法、检验规则及标志、包装、运输和贮存。 本标准适用于气缸直径大于160 mm的新造往复式内燃机大功率柴油机整体连续纤维锻钢曲轴（以下简称曲轴）的设计、制造与验收。
Reciprocating internal combustion engines.High power diesel engine.Continuous grain flow forged steel crankshaft.Specification
- ICS
- 27.020
- CCS
- J92
- 发布
- 2014-05-06
- 实施
- 2014-10-01
本标准规定了往复式内燃机大功率柴油机整体连续纤维锻钢曲轴磁粉湿法连续法检测的设备、环境、人员、器材、磁化规范、性能校验、检验区域、验收条件和检测记录等。 本标准适用于气缸直径大于160 mm的新造往复式内燃机大功率柴油机整体连续纤维锻钢曲轴（以下简称曲轴）的湿法连续法磁粉检测与缺陷评定。其他内燃机整体连续纤维锻钢曲轴可参照使用。
Reciprocating internal combustion engines.High power diesel engine.Continuous grain flow forged steel crankshaft.Inspection method: Wet-process continuous magnetic particle inspection
- ICS
- 27.020
- CCS
- J92
- 发布
- 2014-05-06
- 实施
- 2014-10-01
本标准规定了内燃机铸造铝合金气缸盖（以下简称气缸盖）的技术要求、检验方法、检验规则、标志、包装、运输和贮存。 本标准适用于气缸直径小于或等于200 mm的往复式内燃机用铸造铝合金气缸盖和气缸盖组件（气缸盖装配了气门导管、气门座、镶块和喷油器套等零件）。
Internal combustion engines.Cast aluminum cylinder heads.Specification
- ICS
- 27.020
- CCS
- J92
- 发布
- 2014-05-06
- 实施
- 2014-10-01
JB/T 7293的本部分规定了内燃机连杆螺栓金相检验的技术要求、检验方法和金相组织评级。 本部分适用于40Cr、35CrMoA、42CrMo以及15MnB、15MnVB、20MnV等钢制造的内燃机连杆螺栓（以下简称连杆螺栓），经热处理后的金相组织检验。
Internal combustion engines.Bolts and nuts.Part 3: Connecting rod bolts.Metallographic examination
- ICS
- 27.020
- CCS
- J92
- 发布
- 2014-05-06
- 实施
- 2014-10-01
本标准规定了往复式内燃机胀断连杆（包括连杆体、连杆盖和连杆衬套）的术语和定义、技术要求、检验方法、检验规则及标志、包装、运输和贮存。 本标准适用于气缸直径不大于200 mm的往复式内燃机用胀断连杆（以下简称胀断连杆）。
Internal combustion engines.Fractured connecting rod.Specification
- ICS
- 27.020
- CCS
- J92
- 发布
- 2014-05-06
- 实施
- 2014-10-01
Internal combustion engines -- Small diameter piston rings -- Part 17: Coil-spring-loaded oil control rings made of steel
- ICS
- 21.240;27.020
- CCS
- J92
- 发布
- 2014-03-20
- 实施
Internal combustion engines.Small diameter piston rings.Part 16: Coil-spring-loaded oil control rings of narrow width made of cast iron
- ICS
- 21.240;27.020
- CCS
- J92
- 发布
- 2014-03-20
- 实施
Internal combustion engines -- Small diameter piston rings -- Part 15: Half keystone rings made of steel
- ICS
- 21.240;27.020
- CCS
- J92
- 发布
- 2014-03-20
- 实施
Internal combustion engines -- Small diameter piston rings -- Part 14: Keystone rings made of steel
- ICS
- 21.240;27.020
- CCS
- J92
- 发布
- 2014-03-20
- 实施
Internal combustion engines -- Small diameter piston rings -- Part 10: Half keystone rings made of cast iron
- ICS
- 21.240;27.020
- CCS
- J92
- 发布
- 2014-03-20
- 实施
本标准规定了内燃机镀铬铝缸体的技术要求、检验方法与检验规则、标志、包装、运输和贮存。本标准适用于气缸内孔直径小于或等于80 mm的往复活塞式内燃机镀铬铝缸体。
Internal combustion engines.Chromeplate cylinder blocks.Specifications
- ICS
- 27.020
- CCS
- J92
- 发布
- 2013-12-31
- 实施
- 2014-07-01
This part of ISO 6622 specifies the essential dimensional features of rectangular rings made of steel, types R, B, BA, and M having nominal diameters from 30 mm up to and including 160 mm, used in reciprocating internal combustion piston engines for road vehicles and other applications.
Internal combustion engines.Piston rings.Part 2: Rectangular rings made of steel
- ICS
- 43.060.10
- CCS
- J92
- 发布
- 2013-11
- 实施
This part of ISO 6621 specifies those quality aspects that are capable of definition but not normally found on a drawing specification.
Internal combustion engines.Piston rings.Part 5: Quality requirements
- ICS
- 43.060.10
- CCS
- J92
- 发布
- 2013-10-01
- 实施
Specifications for ceramic coated piston rods
- ICS
- CCS
- J92
- 发布
- 2013-10-01
- 实施
- 2013-10-01
Internal combustion engines. Piston rings. Quality requirements
- ICS
- 43.060.10
- CCS
- J92
- 发布
- 2013-09-30
- 实施
- 2013-09-30
This part of ISO 6626 specifies the essential dimensional features of coil-spring-loaded oil control rings made of cast iron, types DSF-C, SSF, GSF, DSF, SSF-L, DSF-NG and DSF-CNP. It is applicable to those piston rings in sizes 60 mm to 11O mm, inclusive, for reciprocating internal combustion engines for road vehicles and other applications.
Internal combustion engines.Piston rings.Part 2: Coil-spring-loaded oil control rings of narrow width made of cast iron
- ICS
- 43.060.10
- CCS
- J92
- 发布
- 2013-08
- 实施
