J93 进、排气系统 标准查询与下载

JB/T 6007-2007 内燃机 油浴及油浸式空气滤清器滤芯 技术条件

本标准规定了内燃机油浴及油浸式空气滤清器滤芯的技术要求、检验规则和标志、包装、运输和贮存。 本标准适用于内燃机油浴及油浸式空气滤清器用的细钢丝等支架制作的滤芯(以下简称钢丝滤芯)和由泡沫塑料等支架制作的滤芯（以下简称泡沫塑料滤芯）。

Internal combustion engines Oil bath and oil immersion air cleaner core Specification

JB/T 10737-2007 内燃机 粉末冶金气门座 技术条件

本标准规定了内燃机粉末冶金气门座的技术要求、检验方法、检验规则和标志、包装、运输、贮存。 本标准适用于气缸直径小于或等于200mm以下的往复活塞式内燃机的镶块式粉末冶金气门座(以下简称气门座)。

Internal combustion engines-Powder metallurgy valve seat inserts-Specification

JB/T 6004-2007 内燃机 油浴及油浸式空气滤清器总成 技术条件

本标准规定了内燃机油浴及油浸式空气滤清器总成的技术要求、检验规则和标志、包装、运输和贮存。 本标准适用于空气体积流量为4000m3/h以下的内燃机油浴及油浸式空气滤清器总成。

Internal combustion engines Oil bath and oil immersion air cleaner assembly Specification

JB/T 10591-2006 内燃机气门弹簧技术条件

Specifications for internal combustion engine valve springs

BS ISO 7967-4:2005 往复式内燃机.零部件和系统词汇.增压及进/排气管道系统

This part of ISO 7967 defines terms relating to pressure charging and air exhaust gas ducting systems for reciprocating internal combustion engines. ISO 2710 gives a classification of reciprocating internal combustion engines and defines basic terms of such engines and their characteristics.

Reciprocating internal combustion engines - Vocabulary of components and systems - Pressure charging and air/exhaust gas ducting systems

SAE J2140-2005 重型发动机上预制进气软管的一般要求

This SAE Standard outlines the requirements for a preformed thermosetting hose intended for use in heavy-duty vehicle engines, such as air cleaner to carburetor hose, where it is exposed to normal heat and splash of motor oil.

General Requirement for Preformed Hoses for Air Induction on Heavy-Duty Engines

ISO 7967-4:2005 往复式内燃机.零部件和系统词汇.第4部分:增压及进/排气管系统

This part of ISO 7967 defines terms relating to pressure charging and air exhaust gas ducting systems for reciprocating internal combustion engines. ISO 2710 gives a classification of reciprocating internal combustion engines and defines basic terms of such engines and their characteristics.

Reciprocating internal combustion engines - Vocabulary of components and systems - Part 4: Pressure charging and air/exhaust gas ducting systems

JB/T 9747-2005 内燃机.空气滤清器.性能试验方法

本标准规定了内燃机空气滤清器性能的试验规程、试验条件、试验设备及试验结果的整理，以便使空气滤清器的试验室性能试验结果具有可比性。 本标准适用于道路车辆、农林机械、工程机械、船舶和固定动力用内燃机空气滤清器的试验。

Internal combustion engines - Air filters - Performance testing

JB/T 6012-2005 内燃机.进、排气门.技术条件

本标准规定了内燃机进、排气门(以下简称气门)的技术要求、检验方法、检验规则和标志、包装、运输、贮存。 本标准适用于气缸直径200mm以下的往复活塞式内燃机气门。

Internal combustion engines - Intake and exhaust valves - Specification

JB/T 9756-2004 内燃机 空气滤清器纸质滤芯 技术条件

　　本标准规定了内燃机空气滤清器纸质滤芯的技术要求、检验方法和检验规则以及标志、包装、运输与贮存。 本标准适用于体积流量4000m^(3)/h以下的内燃机空气滤清器纸质滤芯。其他干式滤芯(如非织造布滤芯等)也可参照执行。

Internal combustion engines - Air filter paper elements - Specifications

JB/T 9752.3-2004 涡轮增压器 转子平衡品质及校验方法

　　JB/T 9752的本部分规定了涡轮增压器转子平衡品质等级、在两校正平面上不平衡量分配的计算和校验方法,以及在图样的标注方法。 本部分适用于增压器各种型式转子的单件或整体动平衡。

Turbocharger - Balance quality requirements and check methods of rotors

ARMY MIL-PRF-50084 G CONT. DIST.-2003 34CMH(20 CFM) 离心风扇[代替:ARMY MIL-F-0050084 F CANC NOTICE2CONT.DIST.]

This commercial item description covers brown kraft paper used for general wrapping applications.

FAN, CENTRIFUGAL, 34CMH (20 CFM) [Use In Lieu Of: ARMY MIL-F-0050084 F CANC NOTICE 2 CONT. DIST.]

DLA MIL-STD-1411 A-2002 压缩气筒的检验和维修

This standard practice is approved for use by all departments and agencies of the Department of Defense (DoD)

INSPECTION AND MAINTENANCE OF COMPRESSED GAS CYLINDERS

BS ISO 8178-9:2001 往复式内燃机.废气排放测量.压燃式发动机瞬态工况排气烟度试验台测量用试验周期和试验规程

This part of ISO 8178 specifies the measurement procedures and test cycles for the evaluation of smoke emissions from compression ignition engines on the test bed. For transient smoke test cycles, smoke testing is conducted using smokemeters which operate on the light extinction principle. The purpose of this part of ISO 8178 is to define the smoke test cycles and the methods used to measure and analyse smoke. Specifications for measurement of smoke using the light extinction principle can be found in ISO 11614. The test procedures and measurement techniques described in clauses 1 to 11 of this part of ISO 8178 are applicable to reciprocating internal combustion (RIC) engines in general. However, an engine application can only be evaluated using this part of ISO 8178 once the appropriate test cycle has been developed. Annexes A and B to this part of ISO 8178 each contain a test cycle that is relevant only for those specific applications listed in the Scope of that annex. Where possible, the smoke test cycle described in the annex utilizes the engine and machine categories developed in part 4 of ISO 8178. For certain categories of non-road engines "at site" rather than "test bed" smoke test procedures may prove to be necessary. For engines used in machinery covered by additional requirements (e.g. occupational health and safety regulations), additional test conditions and special evaluation methods may apply.

Reciprocating internal combustion engines - Exhaust emission measurement - Test cycles and test procedures for test-bed measurement of exhaust gas smoke emissions from compression ignition engines operating under transi ent conditions

BS ISO 5011:2001 内燃机和压缩机的进气口净化装置.性能测试

This International Standard establishes and specifies uniform test procedures, conditions, equipment, and a performance report to permit the direct laboratory performance comparison of air cleaners. The basic performance characteristics of greatest interest are air flow restriction or differential pressure, dust collection effciency, dust capacity, and oil carry-over on oil bath air cleaners. This test code therefore deals with the measurement of these parameters. This International Standard is applicable to air cleaners used on internal combustion engines and compressors generally used in automotive and industrial applications.

Inlet air cleaning equipment for internal combustion engines and compressors. Performance testing

BOCA IMC-2000 CHAPTER 5-2000 排气系统

The provisions requiring that the excavation left when an unfit structure has been removed be filled in is an obvious, but often neglected means of protecting the public health and safety.

Exhaust Systems

JB/T 51024-1999 内燃机 空气滤清器纸质滤芯 产品质量分等

Quality classification of paper filter elements for internal combustion engine air filters

JB/T 51117-1999 内燃机 气门座 产品质量分等

Quality grading of internal combustion engine valve seat products

JB/T 51113-1999 内燃机 空气滤清器总成 产品质量分等

Product Quality Grading of Air Filter Assembly for Internal Combustion Engines

JB/T 51119-1999 内燃机 气门挺柱 产品质量分等

Quality grading of valve lifters for internal combustion engines