K21 同步电机 标准查询与下载

ANSI/IEEE 1665:2009 50和60Hz、额定电压1MVA及以上同步发电机的反绕用指南

The general parameters for this Guide apply to 50 or 60 hertz synchronous generators driven by reciprocating engines, steam turbines, combustion turbines, and hydro turbines. The guide generally applies to the stator and rotor of generators with rated outputs of 1 MVA and above.

Guide for the Rewind of Synchronous Generators, 50 and 60 Hz, Rated 1 MVA and Above

IEEE 1665-2009 50和60Hz、额定电压1MVA及以上同步发电机的反绕用指南

Guide for the rewind of synchronous generators, 50 Hz and 60 Hz, rated 1 MVA and above

IEEE 115-2009 同步机的试验规程.第1部分:验收和性能试验.第2部分:同步分析用试验规程和参数测定

Guide for Test Procedures for Synchronous Machines Part I-Acceptance and Performance Testing Part II-Test Procedures and Parameter Determination for Dynamic Analysis

BS EN 60034-3:2008 旋转电机.第3部分:由蒸汽轮机或燃气轮机的同步发电机的特殊要求

This part of IEC 60034 applies to three-phase synchronous generators, having rated outputs of 10 MVA and above driven by steam turbines or combustion gas turbines. It supplements the basic requirements for rotating machines given in IEC 60034-1. Common requirements are prescribed together with specific requirements for air, for hydrogen or for liquid cooled synchronous generators. This part of IEC 60034 also gives the precautions to be taken when using hydrogen cooled generators including: – rotating exciters driven by synchronous generators; – auxiliary equipment needed for operating the generators; – parts of the building where hydrogen might accumulate. NOTE 1 These requirements also apply to a synchronous generator driven by both a steam turbine and a combustion gas turbine as part of a single shaft combined cycle unit. NOTE 2 These requirements do not apply to synchronous generators driven by water (hydraulic) turbine or wind turbine. NOTE 3 The precautions to be taken when using hydrogen are valid for all cases where hydrogen is used as a coolant.

Rotating electrical machines -Part 3: Specific requirements for synchronous generators driven by steam turbines or combustion gas turbines

SANS 60034-3:2008 旋转电机.第3部分:蒸汽涡轮机或燃气涡轮机驱动的同步发电机具体要求

Applies to three-phase synchronous generators, having rated outputs of 10 MVA and above driven by steam turbines and combustion gas turbines. It supplements the basic requirements for rotating machines given in SANS 60034-1.

Rotating electrical machines Part 3: Specific requirements for synchronous generators driven by steam turbines or combustion gas turbines

JB/T 7803-2007 仪用步进电动机

本标准规定了仪用步进电动机的分类、通用技术要求、试验方法、检验规则、质量保证期及标志、包装、运输和贮存。 本标准适用于机座外径不大于90mm的磁阻式、永磁式、混合式和反应式步进电动机。

Instrument employed step motor

JB/T 7805-2007 记录仪表用永磁同步电动机

本标准规定了记录仪表用永磁同步电动机的基本参数、技术要求、试验方法、检验规则及标志、包装、运输和贮存。 本标准适用于频率为50Hz或60Hz的永磁同步电动机。

Permanent magnet synchronous motors for recorders

JB/T 7804-2007 记录仪表用交流伺服电动机

本标准规定了记录仪表用交流伺服电动机的基本参数、技术要求、试验方法、检验规则及标志、包装、运输和贮存。 本标准适用于频率为50Hz或60Hz，输出功率为5W以下，以电容分相的交流伺服电动机。

A.C.Servomotors for Recorders

JB/T 10747-2007 整体凸极式无刷三相同步发电机技术条件

本标准规定了往复式内燃机驱动的整体凸极式无刷三相同步发电机（以下简称发电机）的型式、基本参数与尺寸，技术要求，检验规则和试验方法以及标志、包装和质量保证期的要求。 本标准适用于往复式内燃机驱动的额定频率为50Hz的整体凸极式无刷三相同步发电机。其他特殊型式的发电机也可参照执行。

Specification for integrated salient pole brushless three-phase synchronous generator

IEEE 421.1-2007 同步机用励磁系统的定义

This standard defines elements and commonly used components in excitation systems and contains definitions for excitation systems applied to synchronous machines. An included annex contains one-line block diagrams of some typical excitation systems. These are presented to illustrate the defined terminology referenced in this standard and clarify the understanding of the excitation control system.

Standard Definitions for Excitation Systems for Synchronous Machines

JB/T 7784-2006 透平同步发电机用交流励磁机 技术条件

本标准规定了透平同步发电机用交流励磁机的型式、技术要求、试验项目以及标志、包装、运输和保管等要求。 本标准适用于透平型同步发电机用的交流励磁机。 凡本标准中未规定的事项，均应符合GB 755中的有关规定。

Technical requirements of AC exciter for turbine-type synchronous generators

BS EN 60034-3:2005 旋转电机.第3部分:鼓形转子同步机的特殊要求

This part of IEC 60034 applies to three-phase cylindrical rotor synchronous machines, having rated outputs of 10 MVA (or MW) and above. It supplements the basic requirements for rotating machines given in IEC 60034-1. The special requirements of machines continuously fed by inverters are not covered by this standard. Common requirements for all cylindrical rotor machines are prescribed together with specific requirements for air, for hydrogen or for liquid cooled cylindrical rotor synchronous machines. This part of IEC 60034 also gives the precautions to be taken when using hydrogen cooled machines including – rotating exciters driven by cylindrical rotor type machines; – auxiliary equipment needed for operating the machines; – parts of the building where hydrogen might accumulate.

Rotating electrical machines — Part 3: Specific requirements for cylindrical rotor synchronous machines

ANSI/IEEE C50.13:2005 10MVA及以上的50和60赫兹鼓形转子同步发电机标准

Contains requirements for all types of 50 and 60 Hz cylinderical rotor synchronous generators rated 10 MVA and above.

Standard for Cylindrical-Rotor 50 and 60 Hz, Synchronous Generators Rated 10 MVA and Above

ANSI/IEEE C50.12:2005 5MVA及以上水轮机设备用50和60赫兹凸极其同步发电机和发电机/电动机标准

Contains requirements for all types of 50 and 60 Hz salient-pole synchronous generators and generator/motors rated 5000 kVA and above to be used for hydraulic turbine or hydraulic pump/turbine applications.

Standard for Salient-Pole 50 and 60 Hz Synchronous Generators and Generator/Motors for Hydraulic Turbine Applications Rated 5 MVA and Above

GJB 1780A-2005 印制绕组直流伺服电动机通用规范

本规范规定了印制绕组直流伺服电动机(以下简称电动机)的技术要求、质量保证规定以及包装、运输、贮存和产品分类等要求。 本规范适用于机座外径不大于φ320mm的电动机。机座外径大于φ320mm的电动机也可参照执行。

DC servomotors with printed armature general specification for

NF C51-113:2005 旋转电机.第3部分:圆柱形转子同步电机的特殊要求

Rotating electrical machines - Part 3 : specific requirements for cylindrical rotor synchronous machines.

IEEE Std C50.13-2005 额定电压高于等于10 MVA鼓形转子 50 Hz 和 60 Hz 同步发电机

The requirements in this standard apply to all types of 50 Hz and 60 Hz salient-pole synchronous generators and generator/motors rated 5 MVA and above to be used for hydraulic turbine or hydraulic pump/turbine applications.

Cylindrical-rotor 50 Hz and 60 Hz synchronous generators rated 10 MVA and above

JB/T 8446-2005 隐极式同步发电机转子匝间短路测定方法

本标准规定了隐极式同步发电机转子匝间短路的测量方法及限定值。 本标准适用于隐极式同步发电机转子匝间短路的测量。发电机的交流励磁机转子匝间试验参照本标准执行。 本标准与GB/T 7064《透平型同步电机的技术要求》协调一致。

Methods for the determination of interturn short-circuit in the rotor winding of cylindrical synchronous generators

JB/T 7071-2005 灯泡式水轮发电机基本技术条件

本标准规定了灯泡式水轮发电机的基本技术要求、试验验收、供货范围、包装运输及保管和承包方的保证。 本标准适用于与水轮机直接连接的三相、5OHz、卧轴灯泡式凸极同步发电机(以下简称灯泡式水轮发电机)。 凡本标准未规定的事项，均应符合GB/T 7894、GB 8564标准中有关规定。

Basic specification for bulb hydro generators

JB/T 10499-2005 透平型发电机非正常运行工况设计和应用导则

本标准规定了透平型发电机在各种非正常运行工况下运行范围及程度的相关要求。 本标准适用于100MW以上容量范围的透平型同步发电机。 本标准可作为使用部门和制造部门签定技术协议时的依据。对具体产品若有特殊要求，可由供需双方另行商定。

Design application guide of turbo generators under abnormal operation