K33 控制继电器 标准查询与下载

BS EN 60255-22-7:2003 电气继电器.测量继电器和保护设备的电干扰试验.工频抗扰试验

This part of IEC 60255 is based on the concepts described in IEC 61000-4-16, referring to that publication where applicable, and specifies the general requirements for power frequency immunity tests for measuring relays and protection equipment for power system protection, including the control, monitoring and process interface equipment used with those systems. The objective of the tests is to confirm that the equipment under test (EUT) will operate correctly when energised and subjected to short duration, conducted, common and differential mode power frequency disturbances applied to DC status inputs, at the rated frequency of the EUT, for example 50/3 Hz, 50 Hz and 60 Hz. The testing of pilot wire schemes between substations is not covered by this standard. The requirements specified in this standard are applicable to measuring relays and protection equipment in a new condition and all tests specified are type tests only. The object of this standard is to state: - definitions of terms used; - test severity levels; - test equipment; - test set-up; - test procedures; - criteria for acceptance; - test report.

Electrical relays - Electrical disturbance tests for measuring relays and protection equipment - Power frequency immunity tests

BS EN 61811-11:2003 机电式全有或全无继电器.空白详细规范.工业用继电器

This part of IEC 61811 is a blank detail specification applicable to electromechanical elementary (non-specified time all-or-nothing) relays of assessed quality for industrial application. It is based on the generic specification IEC 61811-1 and the sectional specification IEC 61811-10 and selects from IEC 61810-7 the appropriate test and measurement procedures to be used in detail specifications derived from this specification. Moreover it contains a basic test schedule to be used in the preparation of such specifications.

Electromechanical all-or-nothing relays. Blank detail specification. Relays for industrial application

IEEE Std C37.95-2002(R2007) 用户使用的互连设备的保护继电器用IEEE指南

This guide contains information on a number of different protective relaying practices for the utility-consumer interconnection. It is intended to cover applications involving service to a consumer that normally requires a transformation between the utility’s supply voltage and the consumer’s utilization voltage. Interconnections supplied at the utilization voltage are not covered. This guide is not intended to supplant specific utility or consumer practices, procedures, requirements, or any contractual agreement between the utility and the consumer. The examples in Clause 7 are used for illustrative purposes only and do not necessarily represent the preferred protection under all conditions. This guide addresses consumers, with or without generation, that are connected to utility subtransmission or transmission circuits. The specific control schemes associated with generation are not addressed. It is not intended to apply necessarily to consumer generation connected to utility distribution circuits.

IEEE Guide for Protective Relaying of Utility-Consumer Interconnections

DIN EN 50205:2003 带强制式引导触点的继电器; 德文版本 EN 50205:2002

Relays with forcibly guided (mechanically linked) contacts; German version EN 50205:2002

KS C IEC 60679-4-1:2002 已评定质量的石英晶体受控振荡器.第4-1部分:空白详细规范.能力鉴定

서 문 이 규격은 1998년에 제1판으로 발행된 IEC 60679-4-1 Quar

Quartz crystal controlled oscillators of assessed quality－Part 4－1 : Blank detail specification－Capability approval

KS C IEC 60368-4-1:2002 经质量评定的压电滤波器.第4-1部分:空白详细规范.能力鉴定

서 문 이 규격은 2000년에 제1판으로 발행된 IEC 60368-4-1 Piez

Piezoelectric filters of assessed quality－Part 4－1：Blank detail specification－Capability approval

KS C IEC 60679-5-1:2002 已评定质量的石英晶体受控振荡器.第5-1部分:空白详细规范.质量验证

서 문 이 규격은 1998년에 제1판으로 발행된 IEC 60679-5-1&##

Quartz crystal controlled oscillators of assessed quality－Part 5－1：Blank detail specification－Qualification approval

IEC 61811-10:2002 经质量评定的机电式有或无继电器.第10部分:分规范.工业用继电器

Is based on the basic relay standard IEC 61810-1 as well as on the generic specification IEC 61811-1 and selects from IEC 61810-7 the appropriate test and measurement procedures to be used in detail specifications derived from this specification

Electromechanical elementary relays of assessed quality - Part 10: Sectional specification; Relays for industrial application

BS EN 61811-51:2002 机电全有或全无继电器.空白详细规范.经质量评定的机电全有或全无电信继电器.非标准化的类型和结构

This part of IEC 61811 is a blank detail specification applicable to electromechanical all-ornothing telecom relays of assessed quality. Relays according to this standard are provided for operation in telecommunication applications. However, as electromechanical all-or-nothing relays, they are also suitable for particular industrial and other applications. This standard selects from IEC 61810-7 and other sources the appropriate methods of test to be used in detail specifications derived from this specification, and contains basic test schedules to be used in the preparation of such specifications in accordance with IEC 61811-1.

Electromechanical all-or-nothing relays. Blank detail specification. Electromechanical all-or-nothing telecom relays of assessed quality. Non-standardized types and construction

BS EN 61811-53:2002 机电全有或全无继电器.空白详细规范.经质量评定的机电全有或全无电信继电器.14 mm x 9 mm基座的双转换触点继电器

This part of IEC 61811 is a blank detail specification applicable to electromechanical allor- nothing telecom relays of assessed quality. Relays according to this standard are provided for operation in telecommunication applications. However, as electromechanical allor- nothing relays, they are also suitable for particular industrial and other applications. This standard selects from IEC 61810-7 and other sources the appropriate methods of test to be used in detail specifications derived from this specification, and contains basic test schedules to be used in the preparation of such specifications in accordance with IEC 61811-1.

Electromechanical all-or-nothing relays. Blank detail specification. Electromechanical all-or-nothing telecom relays of assessed quality. Two change-over contacts, 14 mm x 9 mm base

BS EN 61811-52:2002 机电的"全有或全无"继电器.空白详细规范.经质量评定的机电的"全有或全无"电信继电器.20 mm x 10 mm 基座的双转换触点继电器

This part of IEC 61811 is a blank detail specification applicable to electromechanical allor- nothing telecom relays of assessed quality. Relays according to this standard are provided for operation in telecommunication applications. However, as electromechanical all-or-nothing relays, they are also suitable for particular industrial and other applications. This standard selects from IEC 61810-7 and other sources the appropriate methods of tests to be used in detail specifications derived from this specification, and contains basic test schedules to be used in the preparation of such specifications in accordance with IEC 61811-1.

Electromechanical all-or-nothing relays - Blank detail specification - Electromechanical all-or-nothing telecom relays of assessed quality - Two change-over contacts, 20 mm x 10 mm base

BS EN 61811-50:2002 电机“全有或全无”继电器.分规范.经质量评定的机电"全有或全无"电信继电器

This part of IEC 61811 is a sectional specification and applies to electromechanical all-ornothing telecom relays of assessed quality. Relays according to this standard are provided for operation in telecommunication applications. However, as electromechanical all-or-nothing relays, they are also suitable for particular industrial and other applications. This standard selects from IEC 61810-7 and other sources the appropriate methods of test to be used in detail specifications derived from this specification, and contains basic test schedules to be used in the preparation of such specifications. Detailed test schedules are contained in the blank detail specifications supplementary to this specification.

Electromechanical all-or-nothing relays - Sectional specification - Electromechanical all-or-nothing telecom relays of assessed quality

BS EN 61811-55:2002 经质量评定的无规定时间的“全有或全无”机电继电器.空白详细规范.经质量评定的"全有或全无"机电电信继电器.11 mm X 7.5 mm 基的双转换触点(最大的)

This part of IEC 61811 is a blank detail specification applicable to electromechanical all-or-nothing telecom relays of assessed quality. Relays according to this standard are provided for the operation in telecommunication applications. However, as electromechanical all-or-nothing relays, they are also suitable for particular industrial and other applications. This standard selects from IEC 61810-7 and other sources the appropriate methods of test to be used in detail specifications derived from this specification, and contains basic test schedules to be used in the preparation of such specifications in accordance with IEC 61811-1. Detailed test schedules are contained in the detail specifications supplementary to this specification.

Electromechanical non-specified time all-or-nothing relays of assessed quality - Blank detail specification - Electromechanical all-or-nothing telecom relays of assessed quality - Two change-over contacts, 11 mm x 7,5 mm (max.) base

BS EN 50205:2002 主动定向(机械连接)触点继电器

This European Standard specifies special requirements and tests for elementary relays with forcibly guided contacts, also known as mechanically linked contacts. These special requirements apply in addition to the general requirements of EN 61810-1, EN 61810-5, EN 116000-3 and EN 60255-23. NOTE 1 This standard does not apply to electromechanical control circuit devices as described in IEC/EN 60947-5-1. NOTE 2 EN 116000-3 is nearly equivalent to IEC 61810-7.

Relays with forcibly guided (mechanically linked) contacts

BS EN 61811-54:2002 经质量评定的机电式"非”规定时间全有或全无继电器.空白详细规范.经质量评定的机电式"全有"或"全无”通讯继电器.两组转换触点15 mm x 7.5 mm 底座

This part of IEC 61811 is a blank detail specification applicable to electromechanical all-or-nothing telecom relays of assessed quality. Relays according to this standard are provided for operation in telecommunication applications. However, as electromechanical all-or-nothing relays, they are also suitable for particular industrial and other applications. This standard selects from IEC 61810-7 and other sources the appropriate methods of tests to be used in detail specifications derived from this specification, and contains basic test schedules to be used in the preparation of such specifications in accordance with IEC 61811-1.

Electromechanical non-specified time all-or-nothing relays of assessed quality - Blank detail specification - Electromechanical all-or-nothing telecom relays of assessed quality - Two change-over contacts, 15 mm x 7,5 mm base

JB/T 56015-2002 电磁式中间继电器可靠性指标及试验方法

本标准规定了电磁式中间继电器的可靠性指标及可靠性试验的要求和方法。 本标准适用于继电器寿命能合理地认为是服从指数分布的产品的可靠性验证试验。

Reliablilty index and test method for magnetic auxiliary relay

NF C01-444:2002 电工词汇.第444部分:初级继电器

Electrotechnical Vocabulary - Part 444 : elementary relays.

NF C01-445:2002 电工词汇.第445部分:定时有或无继电器

Electrotechnical Vocabulary - Part 445 : specified time all-or-nothing relays.

KS C 8328-2002 漏电继电器

이 규격은 주파수 60 Hz의 교류 600 V 이하인 전로에 사용하는 정격 전류 2 500

Residual current sensing and relaying equipment

IEEE Std C37.90.1-2002 与电力装置相关的继电器和中继系统的耐电涌性能试验

Specifies design tests for relays and relay systems that relate to the immunity of this equipment to repetitive electrical transients. The oscillatory and fast transient SWC tests are defined as distinct tests.

Surge withstand capability (SWC) tests for relays and relay systems associated with electric power apparatus