K43 高压开关设备 标准查询与下载

DIN 43453:2011 单支撑接地转换开关.额定电压420 kV-端头和安装尺寸,电路设计

Single-support earthing switch - Rated voltage 420 kV - Terminal and mounting dimensions, layout

ANSI/NEMA AB4-2011 商用和工业用模制管壳断路器的检查和预防性维修指南

Guidelines for Inspection and Preventive Maintenance of Molded Case Circuit Breakers Used in Commercial and Industrial Applications

ANSI/IEEE C37.122.3:2011 六氟化硫(SF6)气体处理用高压(超过1000 V) 设备用指南

Guide for Sulphur Hexafluoride (SF6) Gas Handling for High Voltage (over 1000 Vac) Equipment

ANSI/IEEE C37.011:2011 交流高压断路器瞬时恢复电压的应用指南

Guide for the Application of Transient Recovery Voltage for AC High-Voltage Circuit Breakers

IEEE Std C37.10-2011 电力断路器故障的调查研究,分析和报告指南

Guide for Investigation, Analysis, and Reporting of Power Circuit Breaker Failures

IEEE Std C37.48.1-2011 高压(γ＞1000 V)限流熔断器的应用,操作和协调的IEEE指南

IEEE Guide for the Application, Operation, and Coordination of High-Voltage (1000 V) Current-Limiting Fuses

IEEE Std C37.30.1-2011 额定电压高于1000 V交流高压空气开关的IEEE标准要求

IEEE Standard Requirements for AC High-Voltage Air Switches Rated Above 1000 V

IEEE Std C37.47-2011 高压(γ＞1000 V)分布类限流器式熔断器和熔断器断开开关规格

Specifications for High-Voltage (>1000 V) Distribution Class Current-Limiting Type Fuses and Fuse Disconnecting Switches

BS EN 50386:2010+A1:2013 注液变压器用1 kV及以下和 250 A至 5 kA的套管

Bushings up to 1 kV and from 250 A to 5 kA, for liquid filled transformers

IEC 62271-101:2010 高压开关设备和控制设备.第101部分:合成试验

This part of IEC 62271 mainly applies to a.c. circuit-breakers within the scope of IEC 62271-100. It provides the general rules for testing a.c. circuit-breakers, for making and breaking capacities over the range of test duties described in 6.102 to 6.111 of IEC 62271-100, by synthetic methods. NOTE Circuits for the test duties described in 6.111 have not yet been standardized. However, present methods are given in Annex G. It has been proven that synthetic testing is an economical and technically correct way to test high-voltage a.c. circuit-breakers according to the requirements of IEC 62271-100 and that it is equivalent to direct testing. The methods and techniques described are those in general use. The purpose of this standard is to establish criteria for synthetic testing and for the proper evaluation of results. Such criteria will establish the validity of the test method without imposing restraints on innovation of test circuitry.

High-voltage switchgear and controlgear. Part 101: Synthetic testing

BS 6626:2010 电压为1 kV以上至36 kV(含)的电气开关设备和控制装置的维护.实用规程

This British Standard gives recommendations and guidance for the maintenance of electrical switchgear and controlgear having a rated a.c. or d.c. voltage above 1 kV and up to and including 36 kV. NOTE 1 This standard is not applicable to explosion protected switchgear and controlgear. Inspection and maintenance of electrical apparatus in explosive gas atmospheres is covered in BS EN 60079-17. NOTE 2 This British Standard covers applications above 1 kV. Voltages below 1 kV are considered to be low voltage in line with the European Commission Directive 73/23/EEC [1], known as the “Low voltage directive”.

Maintenance of electrical switchgear and controlgear for voltages above 1 kV and up to and including 36 kV - Code of practice

DIN EN 60282-1:2010 高压熔断器.第1部分:限流熔断器(IEC 60282-1-2009).德文版本EN 60282-1-2009

High-voltage fuses - Part 1: Current-limiting fuses (IEC 60282-1:2009); German version EN 60282-1:2009

BS PD CLC/TR 62271-208:2010 高压开关设备和控制设备.第208部分: 由HV控制器组件和HV/LV预制变电站产生的稳态工频电磁场量化方法

This part of IEC 62271 gives practical guidance for the evaluation and documentation of the external electromagnetic fields which are generated by HV switchgear assemblies and HV/LV prefabricated substations. Basic requirements to measure or calculate the electric and magnetic fields are summarised for switchgear assemblies covered by IEC 62271-200 and IEC 62271-201, and for prefabricated substations covered by IEC 62271-202. This technical report applies to equipment rated for voltages up to and including 52 kV and power-frequencies from 15 Hz to 60 Hz. The electromagnetic fields which are generated by harmonics or transients are not considered in this technical report. However, the methods described are equally applicable to the harmonic fields of the power-frequency. Detailed generic information on requirements and measurements of low-frequency electromagnetic fields is given in IEC 61786. This technical report covers evaluation under factory or laboratory conditions before installation. The electric and the magnetic fields can be evaluated either by measurements or by calculations. It is not within the scope of this technical report to specify limit values of electromagnetic fields or methods for the assessment of human exposure.

High-voltage switchgear and controlgear Part 208: Methods to quantify the steady state, power-frequency electromagnetic fields generated by HV switchgear assemblies and HV/LV prefabricated substations

IEEE Std C37.04/INT 1-2010 IEEE Std C37.04 ™-1999,IEEE Std C37.06™-2000和IEEE Std C37.09™-1999的IEEE标准解释文件

This is an interpretation of IEEE Std C37.04-1999, IEEE Std C37.06-2000, and IEEE Std C37.09-1999. Interpretations are issued to explain and clarify the intent of a standard and are not intended to constitute an alteration to the original standard or to supply consulting information. Permission is hereby granted to download and print one copy of this document. Individuals seeking permission to reproduce and/or distribute this document in its entirety or portions of this document must contact the IEEE Standards Department for the appropriate license. Use of the information contained in this document is at your own risk.

IEEE Standards Interpretations for IEEE Std C37.04 ™-1999, IEEE Std C37.06™-2000, and IEEE Std C37.09™-1999

NF C64-460*NF EN 50532:2010 配电变电站用小型设备装配(CEADS)

Compact Equipment Assembly for Distribution Substations (CEADS).

DIN EN 60644:2010 汽车动力电路用高压熔断体规范(IEC 60644-2009).德文版本EN 60644-2009

Specification for high-voltage fuse-links for motor circuit application (IEC 60644:2009); German version EN 60644:2009

IEC 61975:2010 高压直流(HVDC)装置.系统测试

This International Standard applies to system tests for high-voltage direct current (HVDC) installations which consist of a sending terminal and a receiving terminal, each connected to an a.c. system. The tests specified in this standard are based on bidirectional and bipolar high-voltage direct current (HVDC) installations which consist of a sending terminal and a receiving terminal, each connected to an a.c. system. The test requirements and acceptance criteria should be agreed for back-to-back installations, while multi-terminal systems and voltage sourced converters are not included in this standard. For monopolar HVDC installations, the standard applies except for bipolar tests. For the special functions or performances that are claimed by specific projects, some extra test items not included in this standard should be added according to the technical specification requirements. This standard only serves as a guideline to system tests for high-voltage direct current (HVDC) installations. The standard gives potential users guidance, regarding how to plan commissioning activities. The tests described in the guide may not be applicable to all projects, but represent a range of possible tests which should be considered. Therefore, it is preferable that the project organization establishes the individual test program based on this standard and in advance assigns responsibilities for various tasks/tests between involved organisations (e.g. user, supplier, manufacturer, operator, purchaser etc.) for each specific project.

High-voltage direct current (HVDC) installations - System tests

DIN V 62271-303:2010 高压开关装置和控制器. 第303部分: 六氟化硫（SF6）的使用和操作; （IEC/TR 62271-303: 2008）; 德文版本CLC/TR 62271-303: 2009

High-voltage switchgear and controlgear - Part 303: Use and handling of sulphur hexafluoride (SF₆) (IEC/TR 62271-303:2008); German version CLC/TR 62271-303:2009

BS EN 50532:2010 配电站用紧凑设备组件（CEADS）

This European Standard specifies the service conditions, rated characteristics, general structural requirements and test methods of the prefabricated assembly of the main electrical functional units of a HV/LV Distribution Substation, duly interconnected, for alternating current of rated operating voltages above 1 kV and up to and including 52 kV on the HV side, service frequency 50 Hz. This assembly is to be cable-connected to the network. This Compact Equipment Assembly for Distribution Substation (CEADS) as defined in this standard is designed and tested to be a single product with a single serial number and one set of documentation. Such equipment is delivered as single transport unit. For practical reasons manufacturer and user can agree to transport the unit dismantled if transport or installation of the complete CEADS is not possible. In that case suitable verification tests shall be carried out at the installation site. A CEADS is not a Distribution Substation, either prefabricated (covered by EN 62271-202) or not (covered by EN 61936-1). However CEADS is intended to become part of a Distribution Substation assembling the HV equipment, the power transformer and the LV equipment duly interconnected (see Annex C, which also explains the origin and types of CEADS). The functions of a CEADS are: – switching and control for the operation of the HV side and protection of the HV/LV transformer functional unit; – HV/LV transformation; – switching and control for the operation and protection of the LV feeders. However relevant provisions of this standard are also applicable to designs where not all of these functions exist (e.g. equipment comprising only HV/LV transformation and switching and control for the operation and protection of the LV feeder functions). For public distribution networks, CEADS are intended for installation within an indoor or outdoor closed electrical operating area (see Definition 1.3.3) forming part of a Distribution Substation. For industrial applications, such as factories, installation of CEADS outside a closed electrical operating area may be allowed provided that safety regulations are fulfilled by additional measures adopted at the installation site under the responsibility of the designer of the installation. This standard considers the potential interaction between the individual functions when closely installed and interconnected to form a type tested assembly and defines ratings, particular design and construction requirements and test procedures for this assembly.

Compact equipment assembly for distribution substations (CEADS)

DL/T 361-2010 气体绝缘金属封闭输电线路使用导则

本标准规定了额定电压为72.5kV及以上、频率为50Hz的气体绝缘金属封闭输电线路(GIL)使用的一般要求、试验方法、运输、储存、安装及运行维护要求。 本标准适用于GIL工程设计和采购。

Technical guide for usage of gas-insulated metal-enclosed transmission line