K43 高压开关设备 标准查询与下载

DL/T 361-2010 气体绝缘金属封闭输电线路使用导则

本标准规定了额定电压为72.5kV及以上、频率为50Hz的气体绝缘金属封闭输电线路(GIL)使用的一般要求、试验方法、运输、储存、安装及运行维护要求。 本标准适用于GIL工程设计和采购。

Technical guide for usage of gas-insulated metal-enclosed transmission line

NF C64-200-1*NF EN 60282-1:2010 高压熔断器.第1部分:限流熔断器

High-voltage fuses - Part 1 : current-limiting fuses.

IEC 62271-101/AMD1:2010 高压开关装置和控制器.第101部分:人工试验

This part of IEC 62271 mainly applies to a.c. circuit-breakers within the scope of IEC 62271- 100. It provides the general rules for testing a.c. circuit-breakers@ for making and breaking capacities over the range of test duties described in 6.102 to 6.111 of IEC 62271-100@ by synthetic methods.NOTE Circuits for the test duties described in 6.111 have not yet been standardized. However@ present methods are given in Annex G.It has been proven that synthetic testing is an economical and technically correct way to test high-voltage a.c. circuit-breakers according to the requirements of IEC 62271-100 and that it is equivalent to direct testing.The methods and techniques described are those in general use. The purpose of this standard is to establish criteria for synthetic testing and for the proper evaluation of results. Such criteria will establish the validity of the test method without imposing restraints on innovation of test circuitry.

High-voltage switchgear and controlgear - Part 101: Synthetic testing

DIN EN 62271-104:2010 高压开关设备和控制设备. 第104部分: 52 kV及以上的额定电压用交流开关（IEC 62271-104: 2009）; 德文版本EN 62271-104: 2009

This standard is applicable to three-pole alternating current switches for rated voltages 52 kV and above, having making and breaking current ratings, for indoor and outdoor installations, and for rated frequencies up to and including 60 Hz. This standard is also applicable to the operating devices of these switches and to their auxiliary equipment.

High-voltage switchgear and controlgear - Part 104: Alternating current switches for rated voltages of 52 kV and above (IEC 62271-104:2009); German version EN 62271-104:2009

IEEE Std C37.20.7/COR 1-2010 小于等于38 kV额定电压的内部电弧故障用封装金属开关设备测试指南.勘误表1

This corrigendum corrects technical errors found in IEEE Std C37.20.7-2007 during use in laboratories concerning current values and arc initiation in low-voltage (LV) testing and supply frequency for all equipment.

IEEE Guide for Testing Metal-Enclosed Switchgear Rated up to 38 kV for Internal Arcing Faults; Corrigendum 1

BS EN 60644:2009 电动机电路用高压熔断体规范

This standard applies primarily to fuse-links used with motors started direct-on-line on alternating current systems of 50 Hz and 60 Hz. NOTE When motors are used with assisted starting this specification can also be applied but particular attention should be paid to the selection of the rated current of the fuse-link (see 8.1) and the manufacturer of the fuse-link should preferably be consulted. Fuse-links according to this specification are intended to withstand normal service conditions and motor starting pulses. They should comply with the requirements of IEC 60282-1. The purpose of this standard is to standardize time-current characteristics, to formulate pulse withstand requirements regarding testing and to give guidance regarding the selection of fuselinks intended to be used with motors.

Specification for high-voltage fuse-links for motor circuit application

SANS 62271-301:2010 高压开关设备和控制设备．第301部分:端子尺寸规格标准化

Applies to high-voltage switchgear and controlgear such as circuit-breakers, disconnectors and switches.

High-voltage switchgear and controlgear Part 301: Dimensional standardisation of high-voltage terminals

IEC TS 62271-304:2008/COR1:2010 高压开关装置和控制装置.第304部分:恶劣气候条件下用额定电压高于1kV小于等于52kV的室内封闭式开关装置和控制装置的设计等级.技术勘误1

High-voltage switchgear and controlgear - Part 304: Design classes for indoor enclosed switchgear and controlgear for rated voltages above 1 kV up to and including 52 kV to be used in severe climatic conditions; Corrigendum 1

DIN EN 62271-110:2010 高压开关设备和控制设备.第110部分:电感负荷开关(IEC 62271-110-2009).德文版本EN 62271-110-2009

This standard is applicable to a.c. circuit-breakers designed for indoor or outdoor installation, for operation at frequencies of 50 Hz and 60 Hz on systems having voltages above 1000 V and applied to inductive current switching with or without additional short-circuit current breaking duties. The standard is applicable to circuit-breakers in accordance with IEC 62271-100 that are used to switch high-voltage motor currents and shunt reactor currents and also to high-voltage contactors used to switch high-voltage motor currents. The main changes from DIN EN 62271-110 (VDE 0671-110):2006-07 are that all references to EN 60694 have been replaced with EN 62271-1.

High-voltage switchgear and controlgear - Part 110: Inductive load switching (IEC 62271-110:2009); German version EN 62271-110:2009

DIN EN 62271-109:2010 高压开关设备和控制设备.第109部分:交流电串联电容器旁路开关(IEC 62271-109-2008).德文版本EN 62271-109-2009

This standard is applicable to a.c. series capacitor by-pass switches designed for outdoor installation and for operation at frequencies of 50 Hz and 60 Hz on systems having voltages above 52 kV. It is only applicable to by-pass switches for use in three-phase systems. This standard is also applicable to the operating devices of by-pass switches and to their auxiliary equipment.

High-voltage switchgear and controlgear - Part 109: Alternating-current series capacitor by-pass switches (IEC 62271-109:2008); German version EN 62271-109:2009

ANSI C37.51a-2010 开关设备用美国国家标准.金属封装低压交流电力线路断路器的开关装置组件.一致性试验程序.修改件1：短时耐受电流试验

This amendment has been developed to coordinate selected conformance tests and procedures with ANSI/IEEE C37.20.1-2002 Metal Enclosed Low-Voltage AC Power Circuit Breaker Switchgear, and particularly, to recognize the amendment C37.20.1a-2005.

"American National Standard for Switchgear - Metal-Enclosed Low-Voltage AC Power Circuit Breaker Switchgear Assemblies - Conformance Test Procedures - Amendment 1: Short-Time Withstand Current Tests".

IEEE Std C37.09b-2010 额定电流基准交流高压电路断路器用测试规程.修改件2:与IEC 62771-100标准协调一致的瞬变恢复电压描述的改变

Test procedure for AC high-voltage circuit breakers rated on a symmetrical current basis - Amendment 2: To change the description of transient recovery voltage for harmonization with IEC 62271-100

ANSI/IEEE C37.09b:2010 额定电流基准交流高压电路断路器用标准试验规程.修改件2:与IEC 62771-100标准协调一致的瞬变恢复电压描述的改变

This test procedure summarizes the various tests that are made on ac high-voltage indoor and outdoor circuit breakers, except for generator circuit breakers, which are covered in IEEE Std C37.013-1997. It describes accepted methods used in making the tests and specifies the tests that will verify assigned ratings under ANSI/IEEE standards. This procedure does not preclude the use of other equivalent or more effective methods of demonstrating ratings.

Standard Test Procedure for AC High-Voltage Circuit Breakers Rated on a Symmetrical Current Basis -Amendment 2: To Change the Description of Transient Recovery Voltage for Harmonization with IEC 62271-100

ANSI/IEEE 1676:2010 应用在电力输电和配电系统中的大功率电子器件(1 MW或更大)控制结构用指南

The scope of this guide is to define and characterize control architecture for high-power electronics from power semiconductor device levels to the power system level. This guide covers the application of power electronics in the areas of Power Quality/Custom Power, Flexible AC Transmission Systems (FACTS), High Voltage DC Transmission (HVDC), Distributed Generation, Energy Storage applications, etc. with a power range from hundreds of kW to thousands of MW, but with emphasis on the 1 MW to hundreds of MW.

Guide for Control Architecture for High Power Electronics (1 MW and Greater) Used in Electric Power Transmission and Distribution Systems

KS C IEC 61958:2009 预制的高压开头设备和控制设备组件.电压内存指示系统

이 표준은 IEC 60298 또는 IEC 60466에서 다루는 교류 배전반 및 제어반에 포

High-voltage prefabricated switchgear and controlgear assemblies-Voltage presence indicating systems

KS C IEC 62271-3:2009 高压开关设备和控制设备.第3部分:基于KS C IEC 61850的数字界面

이 표준은 고전압 개폐장치와 제어장치(IEC SC 17A의 범위) 및 조립품(IEC SC

High-voltage switchgear and controlgear－Part 3：Digital interfaces based on KS C IEC 61850

DIN EN 62271-100:2009 高压开关设备和控制设备.第100部分:交流电路.断路器 (IEC 62271-100:2008);德文版EN 62271-100:2009

High-voltage switchgear and controlgear - Part 100: Alternating current circuit-breakers (IEC 62271-100:2008); German version EN 62271-100:2009

SANS 62271-303:2009 高压开关装置和控制器．第303部分:六氟化硫(SF6)的使用和操作

Addresses the procedures for safe and environmental compatible handling of SF6 during installation, commissioning, normal and abnormal operations and disposal at the end-of-life of high-voltage switchgear and controlgear, and the storage and transportati

High-voltage switchgear and controlgear Part 303: Use and handling of sulphur hexafluoride (SF6)

IEEE Std C37.20.7/INT 1-2009 小于等于38 kV额定电压的内部电弧故障用封装金属开关设备测试指南

Guide for Testing Metal-Enclosed Switchgear Rated Up to 38 kV for Internal Arcing Faults

BS EN 62501:2009 高电压直流输电(HVDC)用电压源换流(VSC)阀.电气测试

This International Standard applies to self-commutated converter valves, for use in a threephase bridge voltage sourced converter (VSC) for high voltage d.c. power transmission or as part of a back-to-back link. It is restricted to electrical type and production tests. The tests specified in this standard are based on air insulated valves. For other types of valves, the test requirements and acceptance criteria must be agreed.

Voltage sourced converter (VSC) valves for high-voltage direct current (H VDC) power transmission. Electrical testing