K47 输电线路器材 标准查询与下载

NF C68-111:1995 电气安装导管系统.第2-1部分:硬性导管系统特殊要求

CONDUIT SYSTEMS FOR ELECTRICAL INSTALLATIONS. PART 2-1 : PARTICULAR REQUIREMENTS FOR RIGID CONDUIT SYSTEMS. (EUROPEAN STANDARD EN 50 086-2-1).

NF C68-113:1995 电气安装导管系统.第2-3部分:挠性导管系统特殊要求

CONDUIT SYSTEMS FOR ELECTRICAL INSTALLATIONS. PART 2-3 : PARTICULAR REQUIREMENTS FOR FLEXIBLE CONDUIT SYSTEMS. (EUROPEAN STANDARD EN 50 086-2-3).

IEC 60900/AMD1:1995 交流1000V和直流1500V以下带电作业用手持工具 修改1

Hand tools for live working up to 1000 V a.c. and 1500 V d.c.; Amendment 1

DIN EN 61057:1995 带电作业用带绝缘杆的1KV a.c以上天线设备

Aerial devices with insulating boom used for life working exceeding 1 kV a.c. (IEC 61057:1991, modified); German version EN 61057:1993

BS 7520:1995 带电作业工具的质量保证规划指南

Based on BS EN ISO 9000 series and includes sampling plans and inspection levels.

Guide to quality assurance plans for tools for live working

IEC 61109/AMD1:1995 标称电压大于1000V的交流架空线路用复合绝缘子 定义、试验方法和验收准则 修改1

Inserts, on page 11, the titles of new standards. Adds, on page 29, the new subclauses 5.5, 5.5.1 and 5.5.2. Replaces, on page 31, subclause 6.4. Adds, on page 33, the new subclause 6.5. Replaces, on page 35, subclause 7.4.

Composite insulators for a.c. overhead lines with a nominal voltage greater than 1000 V - Definitions, test methods and acceptance criteria; Amendment 1

NF C68-100:1995 电气用导管.电气设备用导管外径和导管及配件螺纹

Conduits for electrical purposes. Outside diameters of conduits for electrical installations and threads for conduits and fittings.

DIN EN 61219:1995 带电作业.挂杆式短路装置用接地设备或接地舆短路设备

Live working - Earthing or earthing and short-circuiting equipment using lances as a short-circuiting device - Lance earthing (IEC 61219:1993); German version EN 61219:1993

ASTM B116-95(2012) 工业运输用深槽(图9)和铜架空线(图8)标准规格

1.1 This specification covers figure-9 deep-section grooved and figure-8 copper trolley wire for use in industrial haulage (Explanatory Note 1). 1.2 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.

Standard Specification for Figure-9 Deep-Grooved and Figure-8 Copper Trolly Wire for Industrial Haulage

ASTM B116-95(2017) 工业运输用9号深槽铜及8号铜制电车架空线的标准规格

1.1 This specification covers figure-9 deep-section grooved and figure-8 copper trolley wire for use in industrial haulage (Explanatory Note 1). 1.2 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only. 1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for Figure-9 Deep-Grooved and Figure-8 Copper Trolley Wire for Industrial Haulage

ASTM B116-95 工业运输用深槽(图9)和铜架空线(图8)标准规范

1.1 This specification covers figure-9 deep-section grooved and figure-8 copper trolley wire for use in industrial haulage (Explanatory Note 1). 1.2 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.

Standard Specification for Figure-9 Deep-Grooved and Figure-8 Copper Trolly Wire for Industrial Haulage

ASTM B116-95(2001) 工业拖曳用深槽(图9)和铜架空线(图8)标准规范

1.1 This specification covers figure-9 deep-section grooved and figure-8 copper trolley wire for use in industrial haulage (Explanatory Note 1). 1.2 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.

Standard Specification for Figure-9 Deep-Grooved and Figure-8 Copper Trolly Wire for Industrial Haulage

ASTM B116-95(2007) 工业运输用9号深槽铜及8号铜制电车架空线的标准规范

1.1 This specification covers figure-9 deep-section grooved and figure-8 copper trolley wire for use in industrial haulage (Explanatory Note 1).1.2 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.

Standard Specification for Figure-9 Deep-Grooved and Figure-8 Copper Trolly Wire for Industrial Haulage

ANSI/IEEE 935:1995 带电作业用工具和设备术语指南

Applies to terminology for tools and equipment used in live line working.

Guide on Terminology for Tools and Equipment to Be Used in Live Line Working

UL 857-1994 线路及有关配件

Busways and associated fittings

NF C68-114:1994 电气设备用导管系统.第2-4部分:地下导管系统的特殊要求

Conduit systems for electrical installations. Part 2-4 : particular requirements for conduit systems buried underground.

BS EN 61230:1996 带电作业.接地或接地和短路用便携式设备

Applicable to equipment using copper cables, copper bars or aluminium bars as the earthing and shortcircuiting media.

Live working - Portable equipment for earthing or earthing and short-circuiting

BS EN 61235:1994 带电作业.电工用绝缘空心管

Applies to synthetic materials intended for tools to work on equipment at voltage above 1 kV but does not cover special attachments.

Live working - Insulating hollow tubes for electrical purposes

NF C68-110:1994 电气安装导管系统.第1部分:一般要求

CONDUIT SYSTEMS FOR ELECTRICAL INSTALLATIONS. PART 1 : GENERAL REQUIREMENTS. (EUROPEAN STANDARD EN 50 086-1).

JIS C 3701:1994 电力线用铸造夹

この規格は，主として特別高圧架空電線路に使用する特別高圧架線金具のうち，ボルト締付形クランプ(以下,クランプという。)について規定する。

Casting clamps for power line use