K47 输电线路器材 标准查询与下载

BS EN 50341-2:2002 交流电压45 kV以上架空电力线.国家标准规范索引

Overhead electrical lines exceeding AC 45 kV - Index of national normative aspects

BS EN 50341-3:2001 交流45 kV以上架空电力线.国家标准规范集

This Part 3-6 is applicable for new high-voltage overhead transmission lines only, not for existing lines in Spain. If some planning/design or execution work on existing lines in Spain has to be performed, the Spanish national committee is to be informed and will decide, case by case, whether this EN will be applicable or which former version of Spanish national standard/document has to be followed.

Overhead electrical lines exceeding AC 45 kV - Set of National Normative Aspects

NF C68-120/A1:2002 电气设备用电缆中继线系统和管道系统.第1部分:一般要求

Cable trunking systems and cable ducting systems for electrical installations - Part 1 : general requirements.

IEC 61243-2:1995/AMD2:2002 带电作业.第2部分:1kV-36kV交流电压用电阻类型.修改件2

This is Amendment 2 to IEC 61243-2-1995 (LIVE WORKING - VOLTAGE DETECTORS - Part 2: Resistive type to be used for voltages of 1 kV to 36 kV a.c. )

Live working - Part 2: Resistive type to be used for voltages of 1 kV to 36 kV a.c.; Amendment 2

KS C 8449-2002 触轮母线槽

이 규격은 주로 공장, 창고 등 사업장의 옥내, 옥측 또는 옥외에 설치되는 크레인 등 이동

Trolley busways

KS C 8462-2002 大正方形互换布线工具安装框

이 규격은 대각형 연용 배선 기구(이하 기구라 한다.)의 부착틀에 대하여 규정한다.

Mounting frame for interchangeable wiring devices of large square boss type

BS EN 60743:2001+A1:2008 带电作业.工具、设备和装置用术语

This International Standard applies to the terminology used to describe tools, equipment, devices and methods used in live working. IEC 60050(651) gives the definitions of all terms used in live working. The present standard permits identification of the tools, equipment and devices and standardizes their names.

Live working - Terminology for tools, equipment and devices

NF C68-102F2:2002 NF C 68-102 et NF C 68-104的插入件

Inserts for NF C 68-102 and NF C 68-104

BS EN 12510:2002 架空线用木杆.强度分级标准

This European Standard specifies the requirements for the handling and storage and the characteristics for inclusion in regional/national/local/buyer standards of visual strength grading of softwood and hardwood poles. It also specifies the marking requirements. This standard identifies the characteristics for which, as a minimum, limits shall be given in visual grading standards or specifications. This standard applies to both softwood and hardwood poles. This standard covers only single poles under cantilever and/or compression loading. For example, this standard does not cover poles used as beams. The provision of poles for use in any overhead line or cable infrastructure shall take into account a range of factors not covered by this standard which will necessitate the specification by the end user of complementary and synonymous attributes to those defined in this standard. This refers to requirements for a number of factors including safety, overhead plant, handling, fittings, installation machinery and working practices including climbing.

Wood poles for overhead lines - Strength grading criteria

BS 8020:2002 带电作业用工具.电压交流1000V或直流1500V及以下的导电轨道系统或其附近工作时使用的绝缘手工工具

This British Standard specifies requirements for insulating hand tools required for work on or in close proximity to conductor rails providing traction supplies, in accordance with BS EN 50163, for electrified railways and mass transit systems operating at voltages up to 1 000 V a.c. or 1 500 V d.c. It is not applicable to hand-held tools conventionally used by electricians and others for work on live electrical apparatus, which are specified in BS EN 60900.

Tools for live working - Insulating hand tools for work on or near conductor rail systems operating at voltages up to 1000 V a.c. or 1500 V d.c

DL/T 763-2001 架空线路用预绞式金具技术条件

Technical requirements for overhead line helical fittings

NF C68-302/A1:2001 电气设备用公制电缆密封垫

Metric cable glands for electrical installations.

IEC 60743:2001 带电作业 工具、设备和装置术语

This International Standard applies to the terminology used to describe tools, equipment, devices and methods used in live working. IEC 60050(651) gives the definitions of all terms used in live working. The present standard permits identification of the tools, equipment and devices and standardizes their names.

Live working - Terminology for tools, equipment and devices

DL/T 764.2-2001 电力金具专用紧固件闭口销

Electric power fitting fasteners Split pin

DL/T 765.1-2001 架空配电线路金具技术条件

Technical requirements for distribution fittings

DL/T 764.1-2001 电力金具专用紧固件六角头带销孔螺栓

Electric power fitting fasteners Hexagon head bolts bolts with split pin hole on shank

DL/T 759-2001 连接金具

Link fittings

DL/T 758-2001 接续金具

Splicing fittings

DL/T 757-2001 耐张线夹

Strain clamp

DL/T 756-2001 悬垂线夹

Suspension Clamp