K80 电源综合 标准查询与下载

IEC 62680-3:2013 数据和电源通用串行总线接口.第3部分:通用串行总线(USB)充电规范,修订版1.2

The Battery Charging Working Group is chartered with creating specifications that define limits as well as detection@ control and reporting mechanisms to permit devices to draw current in excess of the USB 2.0 specification for charging and/or powering up from dedicated chargers@ hosts@ hubs and charging downstream ports. These mechanisms are backward compatible with USB 2.0 compliant hosts and peripherals.

Universal Serial Bus interfaces for data and power - Part 3: USB Battery Charging Specification, Revision 1.2

SAE J1715-2-2013 电池术语

This SAE Information Report contains definitions for energy storage system and battery terminology. It is intended that this document be a resource for those writing other batter, HEV and EV documents, specifications, standards, or recommended practices.

Battery Terminology

JB/T 11395-2013 电除尘用三相高压整流电源

本标准规定了电除尘用工频、晶闸管移相调压控制三相高压整流电源的产品型号、性能参数、技术要求、检验规则、试验方法、标志、包装、运输和贮存。本标准适用于电除尘用三相高压整流电源。

Three-phase high-voltage rectifier power source for electrostatic precipitator

IEC 62040-4:2013 不间断电源系统(UPS).第4部分:环境因素.要求和报告

This part of the IEC 62040 series specifies the process and requirements to declare the environmental aspects concerning uninterruptible power systems (UPS), with the goal of promoting reduction of any adverse environmental impact during a complete UPS life cycle. This product standard is harmonized with the applicable generic and horizontal environmental standards and contains additional details relevant to UPS.

Uninterruptible power systems (UPS) - Part 4: Environmental aspects - Requirements and reporting

ANSI/UL 1989-2013 备用电池

Standby Batteries

ANSI/UL 1989a-2013 备用电池

Standby Batteries

ANSI/UL 294B-2013 访问控制系统和设备用以太网供电(PoE)电源来源安全性标准

Standard for Safety for Power Over Ethernet (PoE) Power Sources for Access Control Systems and Equipment

ANSI/UL 294-2013 访问控制系统单元安全性标准

Standard for Safety for Access Control System Units

SN/T 3324.3-2012 进出口信息技术设备检验技术要求 第3部分：外部电源的能效

SN/T 3324的本部分规定了进出口外部电源的能效的要求、检验及结果判定的方法。本部分适用于进口或出口到欧盟、美国或其他国家(地区)的外部电源。对于进口的外部电源不适用于直流-直流转换器。对于出口到欧盟的外部电源不适用于：电压转换器；不间断电源(UPS)；电池充电器：卤素灯转换器；医疗器械的外部电源；在2015年6月30号之前在市场上作为7月24日前出现在市场上的外部电源的售后服务部件或备用部件的、且这些售后服务部件或备用部件或它们的包裹能清晰地表明该售后服务部件或备用部件预定和主要负载一起使用的外部电源。对于出口到美国的外部电源不适用于：按照美国联邦食品，药品和化妆品法(21 U. S. C.360c)513规定，需要联邦食品和药物管理局列名和批准的医疗设备；提供给可拆卸电池组件的充电器电源的装置，或对于完全或主要由电机运行的产品，给该产品的电池充电的装置。

Technical requirements for the inspection of information technology equipment for import and export.Part 3:Energy efficiency of external power supplies

DB35/T 1305-2012 LED道路照明驱动电源

本标准规定了LED道路照明驱动电源的术语和定义、技术要求、试验方法、检验规则、标志、包装、使用说明、存储和运输。 本标准适用于LED道路照明灯具的驱动电源。 隧道、庭院、停车场等公共场所的LED照明灯具用驱动电源（功率20W及以上）也可参照执行。

LED road lighting drive power supply

ETSI EN 301 893-2012 宽带无线接入网(BRAN).5GHz高性能RLAN. 涵盖R&TTE指令V1.7.1第3.2条中的基本要求的协调EN指令

Broadband Radio Access Networks (BRAN); 5 GHz high performance RLAN; Harmonized EN covering the essential requirements of article 3.2 of the R&TTE Directive (V1.7.1)

SJ/T 11432-2012 直流稳定电源通用规范

本规范的第1部分适用于从交流或直流源取得电能,提供直流输出功率的稳定电源,它们用于以下用途,但不局限于此:--计算机;--电信;--实验室;--工业设备。本部分不适用于电气测量用的校准源。本规范的第2部分规定了直流稳定电源的性能要求。当电源是设备的一部分,而该设备对应于某些专用标准时,则应使用这些专用标准。当这些专用标准不能全面包括电源性能特性时,也可以使用本部分作为附加标准。通过对电源设备的关键参数的定义,并规定其对应的不同级别的性能要求,可以使得我们在不同的使用场合指定电源的相应性能指标。由于这些级别都经过了仔细的分级,制造商和用户可以根据自身使用要求选择所需的电源。表2是性能项目要求和试验方法的对照表。本规范的第3部分推荐的试验程序,可以对恒压或恒流电源有关的性能特性进行测定。本部分所述方法不是唯一方法,但由于其可靠性,可以据此对其它试验程序进行仲裁。本部分中尽可能减少使用专用的设备,且不推荐任何具体型号的仪器。本规范的第4部分规定了直流稳定电源的电磁兼容性要求。本部分适用于直流输出不超过200V,功率不超过30kW,且一次侧交流或直流供电不超过600V的电源。这些电源可以单独使用,也可以与其它设备配套使用,这些配套设备应具有足够电气和机械防护。对于某些特殊工业用的电源,例如用于医药和冶金工业的电源来说,可能存在有其它的电磁兼容性标准。此时,可以采用本部分作为备选标准。由于许多电源都作为更大型装置的部件使用,而这些装置都对应各种不同电磁兼容性标准,因此下列a)和b)项列出了电源分类和相关适用电磁兼容性标

General specification of stabilized power supplies, DC output

ANSI/NFPA 110-2012 应急和备用电源系统标准

1.1 Scope. This standard covers performance requirements for emergency and standby power systems providing an alternate source of electrical power to loads in buildings and facilities in the event that the primary power source fails. 1.1.1 Power systems covered in this standard include power sources, transfer equipment, controls, supervisory equipment, and all related electrical and mechanical auxiliary and accessory equipment needed to supply electrical power to the load terminals of the transfer equipment. 1.1.2 This standard covers installation, maintenance, operation, and testing requirements as they pertain to the performance of the emergency power supply system (EPSS). 1.1.3 This standard does not cover the following: (1) Application of the EPSS (2) Emergency lighting unit equipment (3) Distribution wiring (4) Utility service when such service is permitted as the EPSS (5) Parameters for stored energy devices (6) The equipment of systems that are not classed as Level 1 or Level 2 systems in accordance with Chapter 4 of this standard 1.1.4* This standard does not establish criteria for stored energy systems. 1.1.5 The selection of any of the following is not within the scope of this standard: (1) Specific buildings or facilities, or both, requiring an EPSS (2) Specific loads to be served by the EPSS (3)*Assignment of type, class, or level to any specific load.

Standard for Emergency and Standby Power Systems

KS C 8504-2011 汽车用铅酸蓄电池

이 표준은 자동차 등 내연기관의 시동, 점등, 전원, ISG(Idling Stop &

Lead-acid batteries for automobiles

BS EN 50563:2011+A1:2013 外部交流直流和交流交流电源.空负载功率和主动模式的平均效率的测定

External a.c. d.c. and a.c. a.c. power supplies. Determination of no-load power and average efficiency of active modes

IEC 62301:2011 家用电器.备用电源的测量

This International Standard specifies methods of measurement of electrical power consumption in standby mode(s) and other low power modes (off mode and network mode), as applicable. It is applicable to electrical products with a rated input voltage or voltage range that lies wholly or partly in the range 100 V a.c. to 250 V a.c. for single phase products and 130 V a.c. to 480 V a.c. for other products. The objective of this standard is to provide a method of test to determine the power consumption of a range of products in relevant low power modes (see 3.4), generally where the product is not in active mode (i.e. not performing a primary function).

Household electrical appliances - Measurement of standby power

KS C 7504-2010 家庭用小型灯

이 표준은 주로 일반 가정에서 사용되는 무색투명[내면 프로스트(frost) 포함], 백색도

Small lamps for household use

DIN EN 61204-7/A11:2010 直流输出低压电源.第7部分:安全性要求.德文版本EN 61204-7-2006/A11-2009

Low voltage power supplies, d.c. output - Part 7: Safety requirements; German version EN 61204-7:2006/A11:2009

SAE J2836-1-2010 插接运载工具和通用输电网间通讯的使用案例

This SAE Information Report establishes use cases for communication between plug-in electric vehicles and the electric power grid, for energy transfer and other applications.

Use Cases for Communication Between Plug-in Vehicles and the Utility Grid

NF C53-204-7/A11:2010 直流输出的低压电源.第7部分:安全要求

Low voltage power supplies, d.c. output - Part 7 : safety requirements.