共找到 914 条与 电子元件综合 相关的标准,共 61 页
This standard specifies marking codes for resistors and capacitors and indexes for the dielectric material and the electrodes of plastic film and paper capacitors.
Marking codes for resistors and capacitors (IEC 60062:2004); German version EN 60062:2005
This list has been prepared for use by or for the Government in the acquisition of products covered by subject specification and such listing of a product is not intended to and does not connote endorsement of the product by the Department of Defense.
CAPACITORS, VARIABLE, CERAMIC DIELECTRIC, GENERAL SPECIFICATION FOR
This list has been prepared for use by or for the Government in the acquisition of products covered by Specification MIL -PRF-14409. Listing of a product is not intended to and does not connote endorsement of the product by the Department of Defense.
CAPACITORS, VARIABLE (PISTON -TYPE, TUBULAR TRIMMER), GENERAL SPECIFICATION FOR
This drawing and MIL-PRF-28861 describe the requirements for radio frequency/electromagnetic interference suppression, hermetically sealed filters and capacitors.
FILTERS AND CAPACITORS, RADIO FREQUENCY/ELECTROMAGNETIC INTERFERENCE SUPPRESSION, HERMETICALLY SEALED
This Publicly Available Specification (PAS) is, first of all, a practical guide to methods of long-duration storage (more than five years) which summarizes the existing practices in the industry. Unless otherwise specified, the approach, as well as the methods presented, apply to all families of electronic components, such as > passive components, including quartz crystals, connectors and relays. However, components with "manufacturer's" specifications showing an expiry date or specific storage conditions are excluded from this document (for example, primary cells, storage cells, etc.); > encapsulated or non-encapsulated active components of a silicon [Si] or gallium arsenide [GaAs] technology; > micro-electronic assemblies.
Electronic components - Long-duration storage of electronic components - Guidance for implementation
이 규격은 개별 규격에서 요구하는 경우, IEC 기술위원회 48의 적용 범위 내에서 전자
Electromechanical components for electronic equipment-Basic testing procedures and measuring methods-Part 16:Mechanical tests on contacts and terminations-Section 20:Test 16t:Mechanical strength(wired termination of solderless connections)
Standards Proposal No. 51 14, Proposed Reaffirmation of ANSI/ EIA-540C000, 540CA00, 540CAAA and 540CAAB “Electrical Relay Socket Specifications” (see table 1 on page iii for individual specification titles and current revision levels)
Electrical Relay Socket Specifications Proposed Reaffirmation for ANSI/EIA-540COOOO, 540CAOOOO, 540CAAA, and 540CAAB
This generic specification applies to electromechanical sockets for use in direct current, analog,and digital applications. This generic specification shall be used in conjunction with the basic specification EM-364 “Electrical Connector Test Procedures I
Generic Specification for Sockets for Use in Electronic Equipment To be published as ANSI/EIA/ECA-5400000-B
Standards Proposal No. 51 12, Proposed Reaffirmation of ANSI/ EIA-700AOAC,EIA-540A000, EIA-540AA00, EIA-540AAAA, EIA-540AB00, EIA-540ABAA,EIA-540AC00, EIA-540ACAA, EIA-540AD00, EIA-540B000, EIA-540BA00,E IA-540 BAAB, E IA-540BAACI EIA-540D000, E IA-540DA0
Electrical Socket Specifications Proposed Reaffirmation of ANSI/EIA-700AOAC, EIA-540AOOO, EIA-540AAOO, EIA-540AAAA, EIA-540ABOO, EIA-540ABAA, EIA-540ACOO, EIA-540ACAA, EIA-540ADOO, EIA-540BOOO, EIA-540BAOO, EIA-540BAAB, EIA-540BAAC, EIA-540DOOO, EIA-540D
Covers conformance tests and requirements for the integrity of above grade pad-mounted enclosures intended for installation in coastal environments containing apparatus energized in excess of 600 volts that may be exposed to the public including, but not limited to, the following types of equipment enclosures: pad-mounted capacitors or inductors, pad-mounted distribution transformers, pad-mounted junction enclosures, pad-mounted metering equipment, pad-mounted switchgear.
Standard for Pad-Mounted Equipment - Enclosure Integrity for Coastal Environments
Covers conformance tests and requirements for the integrity of above grade pad-mounted enclosures containing apparatus energized in excess of 600 volts that may be exposed to the public including, but not limited to, the following types of equipment enclosures: pad-mounted capacitors or inductors, pad-mounted distribution transformers, pad-mounted junction enclosures, pad-mounted metering equipment, pad-mounted switchgear.
Standard for Pad-Mounted Equipment - Enclosure Integrity
이 규격에 제시된 치수는 IEC 60390(1972) 및 60620(1984)로부터 발췌하
Capacitors and resistors for electronic equipment-Preferred dimensions of spindle ends, bushes and for the mounting of single-hole, bush-mounted, spindle-operated electronic components
This drawing and MIL-PRF-28861 describe the requirements for radio frequency interference filters and capacitors.
FILTERS AND CAPACITORS, RADIO FREQUENCY/ELECTROMAGNETIC INTERFERENCE SUPPRESSION, HERMETICALLY SEALED ON ONE END ONLY
This drawing and MIL-PRF-28861 describe the requirements for radio frequency interference filters and capacitors.
FILTERS AND CAPACITORS, RADIO FREQUENCY/ELECTROMAGNETIC INTERFERENCE SUPPRESSION, HERMETICALLY SEALED ON ONE END ONLY
This drawing and MIL-PRF-28861 describe the requirements for radio frequency interference filters and capacitors.
FILTERS AND CAPACITORS, RADIO FREQUENCY/ ELECTROMAGNETIC INTERFERENCE SUPPRESSION, HERMETICALLY SEALED ON ONE END ONLY
No devices listed are to be JAN branded or marked with the failure rate level but should be marked with the appropriate national part numbers and identifiers, as applicable.
CAPACITORS, FIXED, CERAMIC DIELECTRIC (GENERAL PURPOSE), GENERAL SPECIFICATION FOR
本规范规定了陶瓷无引线片式载体(以下简称载体)的详细要求。
Datail specification for ceramic leadless chip carrier
This specification covers the general requirements for low-pass filter and capacitors used to suppress radio frequency/electromagnetic interference. Filters furnished to the requirements of this specification contain shunting ceramic discoidal capacitors and series inductors (FSC 5915).
FILTERS AND CAPACITORS, RADIO FREQUENCY/ELECTROMAGNETIC INTERFERENCE SUPPRESSION, GENERAL SPECIFICATION FOR
This standard establishes requirements and other considerations
Specification for Immersion Silver Plating for Printed Circuit Boards
本指导性技术文件规定了军用密封电气、电子和机电元器件(以下简称元器件)的检漏方法在实施过程中应注意的有关问题。 本指导性技术文件适用于军用元器件在生产、筛选、验收和破坏性物理分析(DPA)等过程中的密封性试验。
Guideline for the practice of leak detection method for sealed military parts
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号