L26 波导同轴元件及附件 标准查询与下载

DIN EN 61338-1-3:2000 波导型介电谐振器.第1-3部分:一般信息和试验条件.微波介电谐振器材料的复相对介电常数的测量方法

The document describes the dielectric rod resonator measurement method for a wide range of microwave dielectric properties in practical applications.

Waveguide type dielectric resonators - Part 1-3: General information and test conditions; Measurement method of complex relative permittivity for dielectric resonator materials at microwave frequency (IEC 61338-1-3:1999); German version EN 61338-1-3:2000

BS EN 61338-1-3:2000 波导型介质谐振器 一般信息和测试条件 微波频率介质谐振器材料复相对介电常数的测量方法

This part of IEC 61338 describes the dielectric rod resonator measurement method for a wide range of microwave dielectric properties in practical applications. This method has the following characteristics: - a complete and exact mathematical solution of complex relative permittivity is given by easy computer software; - the measurement error is less than 0,3 % for ε' and less than 0,05 × 10 for tan δ; - the TCF is directly measured without any compensation with a measurement error less than 1 × 10/K. The object of this standard is to describe the measurement methods of the complex relative permittivity of dielectric resonator materials at microwave frequencies by means of the dielectric rod resonator method short-circuited at both ends by parallel conducting plates. The measuring parameters are ε', tan δ, TCF and the temperature dependence of tan δ at the resonance frequency. The dielectric materials are assumed to be isotropic and homogeneous.

Waveguide type dielectric resonators.. General information and test conditions. Measurement method of complex relative permittivity for dielectric resonator materials at microwave frequency

BS EN 170000:1999 电子元器件质量评估协调系统.通用规范:波导型介质谐振器

This Generic Specification applies to waveguide type dielectric resonators of assessed quality using either capability approval or qualification approval procedures. It also lists the test and measurement procedures which may be selected for use in detail specifications for such resonators.

Harmonized system of quality assessment for electronic components - Generic specification: waveguide type dielectric resonators

NF C93-584-1:1999 射频和同轴电缆组件.第1部分:总规范.一般要求和试验方法

Radio frequency and coaxial cable assemblies - Part 1 : generic specification - General requirements and test methods.

DIN EN 61580-4:1999 波导的测量方法.第4部分:波导衰减和波导组件

The document applicable to attenuation of waveguides and waveguide assemblies.

Methods of measurement for waveguides - Part 4: Attenuation of waveguide and waveguide assemblies (IEC 61580-4:1997); German version EN 61580-4:1998

BS EN 61196-3:1999 射频电缆 规格 局域网用同轴电缆截面规范

This sectional specification specifies requirements for radio frequency coaxial cables for local area networks. The object of this sectional specification is to prescribe recommended ratings and characteristics and to select from the generic specification the appropriate quality assessment procedures, test and measuring methods, and to give general performance requirements for coaxial cables for local area networks plus complementary test methods. Test severities and requirements prescribed in detail specifications referring to this sectional specification should be of equal or higher performance levels. When the requirements of IEC 61196-1 and of this sectional specification conflict with each other, this sectional specification shall prevail.

Radio-frequency cables. Specifications. Sectional specification for coaxial cables for local area networks

BS EN 61580-4:1998 波导的测量方法 波导和波导组件的衰减

This part of IEC 61580 is applicable to attenuation of waveguides and waveguides assemblies. The objective of the test procedures given below is to characterize the attenuation.

Methods of measurement for waveguides. Attenuation of waveguide and waveguide assemblies

NF C93-592:1998 波导法兰.第2部分:普通矩形波导法兰用相关规范

Flanges for waveguides. Part 2 : relevant specifications for flanges for ordinary rectangular waveguides.

SJ 20470.2-1998 40PHX120型波导转换驱动器详细规范

Driver of waveguide switch type 40PHX120,detail specification for

SJ 51510/2-1998 8类不可扭毫米波软波导组件详细规范

Waveguide assemblies,millimeter,flexible,nontwistable,class 8,detail specification for

DIN EN 61580-3:1998 波导管的测量方法.第3部分:群时延的变化

The document is applicable to the variation of group delay of a wave propagated in waveguide or waveguide assemblies. The objective of the test procedures given below is to characterize the group delay variation of a wave propagated in waveguide or waveguide assemblies.

Methods of measurement for waveguides - Part 3: Variation of group delay (IEC 61580-3:1997); German version EN 61580-3:1997

DIN EN 61580-6:1998 波导管的测量方法.第6部分:波导管和波导管组件的回波损耗

The document is applicable to the sweep frequency method used for the measurement of return loss on waveguide and waveguide assemblies.

Methods of measurement for waveguides - Part 6: Return loss on waveguide and waveguide assemblies (IEC 61580-6:1995); German version EN 61580-6:1997

BS EN 61337-1-1:1998 使用波导型介电谐振器的滤波器.一般信息、标准值和试验条件.一般信息和标准值

To be read in conjunction with BS EN 60068-1:1995

Filters using waveguide type dielectric resonators - General information, standard values and test conditions - General information and standard values

NF C93-593-6*NF EN 61580-6:1998 波导的测量方法.第6部分:波导和波导组件的回波损耗

Methods of measurement for waveguides. Part 6 : return loss on waveguide and waveguide assemblies.

BS EN 61580-3:1997 波导的测量方法 群时延的变化

This part of IEC 61580 is applicable to the variation of group delay of a wave propagated in waveguide or waveguide assemblies. The objective of the test procedures given below is to characterize the group delay variation of a wave propagated in waveguide or waveguide assemblies.

Methods of measurement for waveguides. Variation of group delay

BS EN 61580-6:1997 波导的测量方法 波导和波导组件的回波损耗

This International Standard is applicable to the sweep frequency method used for the measurement of return loss on waveguide and waveguide assemblies. Return loss is defined as ar = 20 log (ui/ur) dB where ui is the magnitude of the incident wave; ur is the magnitude of the reflected wave. Return loss is related to the reflection coefficient, r, by: r=(ur/ui) r=10 Fundamentally the method involves measuring the amplitude of the reflected wave at the waveguide under test (WUT) input by means of a ref lectometer device. The reflected wave can be compared with the total reflected wave under short-circuit conditions, attenuated by a calibrated attenuator, or it can be compared with the incident wave by means of reflectometer.

Methods of measurement for waveguides. Return loss on waveguide and waveguide assemblies

IEC 61580-4:1997 波导测量方法 第4部分:波导和波导组件的衰减

This part of IEC 61580 is applicable to attenuation of waveguides and waveguides assemblies. The objective of the test procedures given below is to characterize the attenuation.

Methods of measurement for waveguides - Part 4: Attenuation of waveguide and waveguide assemblies

SJ 51065/6-1997 GBX007型小型化波导射频隔离器详细规范

Detail Specification for Type GBX007 Miniature Waveguide RF Isolators

IEC 61580-3:1997 波导测量方法 第3部分:群时延的变化

This part of IEC 61580 is applicable to the variation of group delay of a wave propagated in waveguide or waveguide assemblies. The objective of the test procedures given below is to characterize the group delay variation of a wave propagated in waveguide or waveguide assemblies.

Methods of measurement for waveguides - Part 3: Variation of group delay

IEC 60154-2:1980/AMD1:1997 波导法兰盘 第2部分:普通矩形波导法兰盘的有关规范 修改1

This is Amendment 1 to IEC 60154-2-1980 (Flanges for waveguides - Part 2: Relevant specifications for flanges for ordinary rectangular waveguides)

Flanges for waveguides - Part 2: Relevant specifications for flanges for ordinary rectangular waveguides; Amendment 1