共找到 274 条与 电子束管 相关的标准,共 19 页
本标准规定了军用视觉显示器的人机工程设计原则和通用要求。 本标准适用于军用视觉显示器的人机工程设计、评价及验收。
General requirements of human-machine engineering design for military visual displays
本规范规定了军用加固液晶显示器的要求、质量保证规定和交货准备等。 本规范适用于军用加固液晶显示器(以下简称显示器)。
General specification for military rugged liquid crystal display
本标准规定了显像管、显示管和电光源用玻管的要求、检验方法、检验规则以及标志、包装、运输和贮存。 本标准适用于显像管、显示管和电光源用玻管。
Glass tube specification for picture tube, displayer tube and electro-optio source
Plasma display panels - Part 4: Climatic and mechanical testing methods (IEC 61988-4:2007); German version EN 61988-4:2007
本规范规定了电荷耦合成像组件(以下简称组件或产品)生产和交付使用的通用要求、质量保证规定、试验和检验方法等。
General specification for imaging charge coupled assemblies
This part of IEC 61988 defines test methods for evaluating environmental and mechanical endurance characteristics of plasma display modules (PDP modules).
Plasma display panels - Climatic and mechanical testing methods
This part of EN 61747 is a blank detail specification for liquid crystal display cells. It should be read together with the generic specification and sectional specification to which it refers.
Liquid crystal display devices — Part 3-1: Liquid crystal display (LCD) cells — Blank detail specification
This PAS applies to commercially available liquid crystal displays (LCDs). This PAS applies to all LCD types, including transmissive, reflective or transflective LCD modules using either segment, passive or active matrix and achromatic or colour-type LCDs that are equipped with their own integrated source of illumination or without their own source of illumination. The object of this PAS is to establish uniform requirements for accurate and reliable measurements of the following LCD parameters, as defined herein: a) quasistatic strength; b) quasistatic fatigue. The methods described in this PAS apply to all sizes, small and large, of LCDs. Methods for measuring the fatigue constant are described in this PAS and are taken from the referenced literature [13-20]. The primary results are formulae for estimated allowable stress for the specified lifetime or estimated failure rate for the specified stress level. By way of an example, limited data for strength and fatigue behaviour of LCD glass are included in an informative annex to this PAS. Similarly, limited data for the static strength of LCD modules is also included and compared with that of parent glass.
Liquid crystal display devices - Part 5-3: Liquid crystal display devices - Glass strength and reliability measurement method
Liquid crystal display devices - Part 3-1: Liquid crystal display (LCD) cells - Blank detail specification (IEC 61747-3-1:2006); German version EN 61747-3-1:2006
This part of IEC 61988 defines test methods for evaluating environmental and mechanical endurance characteristics of plasma display modules (PDP modules).
Plasma display panels - Part 4: Climatic and mechanical testing methods
This sectional specification applies to liquid crystal cells of the segment type monochrome. It gives details of the quality assessment procedures, the inspection requirements, screening sequences, sampling requirements and test and measurement procedures required for the assessment of liquid crystal display cells.#,,#
Liquid crystal display devices - Part 3: Liquid crystal display (LCD) cells - Sectional specification (IEC 61747-3:2006); German version EN 61747-3:2006
The General Services Administration has authorized the use of this commercial item description as a replacement for Military Specifications MIL-V-16720E and MIL-V-16721D which are cancelled.
ELECTRON TUBES, GENERAL SPECIFICATION FOR
This specification covers the requirements for the preservation, packing, and container marking of electron tubes and associated accessories
ELECTRON TUBES, PACKAGING OF
Liquid crystal display devices - Part 3 : liquid crystal diplay (LCD) cells - Sectional specification.
This document describes the portion of the Power Line or RF Physical Layer that interfaces to the Medium Access Control (MAC) Sublayer and to Layer System Management (LSM). This sublayer is called the Power Line/RF Symbol Encoding (PL/RF SE) Sublayer. The PL/RF SE Sublayer provides two primary functions:
Recommended Practice for Transmitter Control and Status Indication in Transmitting Portable Electronic Devices (T-PEDs) (Contains Color)
This standard was developed by the Consumer Electronics Association’s (CEA) Mobile Electronics Committee (R6).
Serial Communication Protocol for Portable Electronic Devices
This sectional specification applies to liquid crystal cells of the segment type monochrome . It gives details of the quality assessment procedures, the inspection requirements, screening sequences, sampling requirements and test and measurement procedures required for the assessment of liquid crystal display cells. Instead of the qualification approval procedure, the capability approval procedure can be applied (see Clause 4 of IECQ 001002-3; however, at present the capability approval procedure for liquid crystal display cells is under consideration) for all products manufactured in a defined process. All the requirements of this specification remain valid, unless modified by the requirements set out in 4.7 of this standard.
Liquid crystal display devices - Liquid crystal display (LCD) cells - Sectional specification
Liquid crystal display devices - Part 3 : sectional specification for liquid crystal display (LCD) cells.
本规范规定了2SG51Y43型单色显示管的详细要求。 本规范适用于2SG51Y43型单色显示管(以下简称单色显示管)。
2SG51Y43, monochrome display tube, detail specification for
本规范规定了M14CNDD01Y43型单色显示管的详细要求。 本规范适用于M14CNDD01Y43型单色显示管(以下简称单色显示管)。
M14CNDD01Y43,monochrome display tube, detail specification for
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号