N23 数字显示仪表 标准查询与下载

DLA SMD-5962-03242 REV A-2004 双信道直流-直流变换器线性混合微电路

This drawing documents five product assurance classes as defined in paragraph 1.2.3 and MIL-PRF-38534. A choice of case outlines and lead finishes which are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of radiation hardness assurance levels are reflected in the PIN.

MICROCIRCUIT, HYBRID, LINEAR, DUAL CHANNEL, DC-DC CONVERTER

DLA SMD-5962-03241 REV A-2004 单信道直流-直流变换器线性混合微电路

This drawing documents five product assurance classes as defined in paragraph 1.2.3 and MIL-PRF-38534. A choice of case outlines and lead finishes which are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of radiation hardness assurance levels are reflected in the PIN.

MICROCIRCUIT, HYBRID, LINEAR, SINGLE CHANNEL, DC-DC CONVERTER

DLA SMD-5962-95696 REV C-2004 5伏特单通道直流电和直流电转换器线型混合微电路

This drawing documents five product assurance classes as defined in paragraph 1.2.3 and MIL-PRF-38534. A choice of case outlines and lead finishes which are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of radiation hardness assurance levels are reflected in the PIN.

MICROCIRCUIT, HYBRID, LINEAR, 5-VOLT, SINGLE CHANNEL, DC-DC CONVERTER

DLA SMD-5962-88776 REV C-2004 硅单片8位快闪记忆体类比数位转换器线性混合微电路

This drawing describes device requirements for class H hybrid microcircuits in accordance with MIL-PRF-38534.

MICROCIRCUIT, HYBRID, LINEAR, 8-BIT, FLASH, ANALOG TO DIGITAL CONVERTER

DLA SMD-5962-95795 REV A-2004 5伏特双通道直流电和直流电转换器线型混合微电路

This drawing documents five product assurance classes as defined in paragraph 1.2.3 and MIL-PRF-38534. A choice of case outlines and lead finishes which are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of radiation hardness assurance levels are reflected in the PIN.

MICROCIRCUIT, HYBRID, LINEAR, 5 VOLT, DUAL CHANNEL, DC/DC CONVERTER

DLA SMD-5962-95796 REV A-2004 12伏特双通道直流电和直流电转换器线型混合微电路

This drawing documents five product assurance classes as defined in paragraph 1.2.3 and MIL-PRF-38534. A choice of case outlines and lead finishes which are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of radiation hardness assurance levels are reflected in the PIN.

MICROCIRCUIT, HYBRID, LINEAR, 12 VOLT, DUAL CHANNEL, DC/DC CONVERTER

DLA SMD-5962-88768 REV F-2003 单一渠道高速逻辑通道光学耦合隔离器数字混合微电路

The complete requirements for procuring the electron tube described herein shall consist of this document and the latest issue of Specification MILE-I.

MICROCIRCUIT, HYBRID, DIGITAL, SINGLE CHANNEL, HIGH SPEED LOGIC GATE OPTICALLY COUPLED ISOLATOR

DLA SMD-5962-94716 REV F-2003 128K X 32-BIT数字反射和消除和编程只读器混合微电路

This drawing documents five product assurance classes as defined in paragraph 1.2.3 and MIL-PRF-38534. A choice of case outlines and lead finishes which are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of radiation hardness assurance levels are reflected in the PIN.

MICROCIRCUIT, HYBRID, DIGITAL, FLASH ERASABLE/ PROGRAMMABLE READ ONLY MEMORY, 128K X 32-BIT

SJ/T 11276-2002 数字式角度测量仪规范

本规范规定了数字式角度测量仪的技术要求、试验方法、检验规则、标志、包装、运输与贮存。 本规范适用于数字式倾角传感器进行重力平面内角度计量的数字式角度测量仪。

Specification for Digital clinometer

DLA SMD-5962-88579 REV A-2002 快速安装视频运算扬声器线性混合微电路

This drawing describes device requirements for class H hybrid microcircuits to be processed in accordance with MIL-PRF-38534 and a choice of case outlines and lead finishes are available and are reflected in the Part or Identifying Number (PIN).

MICROCIRCUIT, HYBRID, LINEAR, FAST SETTLING VIDEO OPERATIONAL AMPLIFIER,

DIN EN 61083-1:2002 高压脉冲试验测量仪器和软件.第1部分:仪器的要求

Instruments and software used for measurements in high-voltage impulse tests - Part 1: Requirements for instruments (IEC 61083-1:2001); German version EN 61083-1:2001

DLA SMD-5962-88658 REV C-2002 12位类比数位转换器线性混合微电路

This drawing describes device requirements for class H hybrid microcircuits to be processed in accordance with MIL-PRF-38534 and a choice of case outlines and lead finishes are available and are reflected in the Part or Identifying Number (PIN)

MICROCIRCUIT, HYBRID, LINEAR, 12-BIT, ANALOG TO DIGITAL CONVERTER

BS EN 61083-1:2001 用于高压脉冲测试测量的数字记录仪 对仪器的要求

This part of IEC 61083 is applicable to digital recorders, including digital oscilloscopes, analogue oscilloscopes and peak voltmeters used for measurements during tests with high impulse voltages and high impulse currents. It specifies the measuring characteristics and calibrations required to meet the measuring uncertainties and procedures specified in IEC 60060-2. This part · defines the terms specifically related to digital recorders, analogue oscilloscopes and peak voltmeters, · specifies the necessary requirements for such instruments to ensure their compliance with the requirements for high-voltage and for high-current impulse tests, and · establishes the tests and procedures necessary to demonstrate their compliance. Only digital recorders that permit access to raw data from permanent or temporary storage are covered by this standard. The raw data, with relevant scaling information, may be · printed graphically, or · stored in digital format.

Digital recorders for measurements in high-voltage impulse tests. Requirements for instruments

IEC 61083-1:2001 高压冲击试验中测量用仪器及软件 第1部分：仪器的要求

This part of IEC 61083 is applicable to digital recorders, including digital oscilloscopes, analogue oscilloscopes and peak voltmeters used for measurements during tests with high impulse voltages and high impulse currents. It specifies the measuring characteristics and calibrations required to meet the measuring uncertainties and procedures specified in IEC 60060-2. This part · defines the terms specifically related to digital recorders, analogue oscilloscopes and peak voltmeters, · specifies the necessary requirements for such instruments to ensure their compliance with the requirements for high-voltage and for high-current impulse tests, and · establishes the tests and procedures necessary to demonstrate their compliance. Only digital recorders that permit access to raw data from permanent or temporary storage are covered by this standard. The raw data, with relevant scaling information, may be · printed graphically, or · stored in digital format.

Instruments and software used for measurement in high-voltage impulse tests - Part 1: Requirements for instruments

ASTM A932/A932M-01(2012) 带片状试样使用电力表.测量表.电压表方法在电源频率下非晶材料的交流电磁性能的标准试验方法

1.1 This test method covers tests for various magnetic properties of flat-cast amorphous magnetic materials at power frequencies (50 and 60 Hz) using sheet-type specimens in a yoke-type test fixture. It provides for testing using either single- or multiple-layer specimens. Note 1???This test method has been applied only at frequencies of 50 and 60 Hz, but with proper instrumentation and application of the principles of testing and calibration embodied in the test method, it is believed to be adaptable to testing at frequencies ranging from 25 to 4008201;Hz. 1.2 This test method provides a test for specific core loss, specific exciting power and ac peak permeability at moderate and high flux densities, but is restricted to very soft magnetic materials with dc coercivities of 0.07 Oe [5.57 A/m] or less. 1.3 The test method also provides procedures for calculating ac peak permeability from measured peak values of total exciting currents at magnetic field strengths up to about 2 Oe [159 A/m]. 1.4 Explanation of symbols and abbreviated definitions appear in the text of this test method. The official symbols and definitions are listed in Terminology A340. 1.5 This test method shall be used in conjunction with Practice A34/A34M. 1.6 The values stated in either customary (cgs-emu and inch-pound) or SI units are to be regarded separately as standard. Within this standard, SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, e......

Standard Test Method for Alternating-Current Magnetic Properties of Amorphous Materials at Power Frequencies Using Wattmeter-Ammeter-Voltmeter Method with Sheet Specimens

ASTM A932/A932M-01(2006) 带片状试样使用电力表.测量表.电压表方法在电源频率下非晶材料的交流电磁性能的标准试验方法

This test method provides a satisfactory means of determining various ac magnetic properties of amorphous magnetic materials. It was developed to supplement the testing of toroidal and Epstein specimens. For testing toroidal specimens of amorphous materials, refer to Test Method A 912/A 912M. The procedures described herein are suitable for use by manufacturers and users of amorphous magnetic materials for materials specification acceptance and manufacturing control. Note 28212;This test method has been principally applied to the magnetic testing of thermally, magnetically annealed, and flattened amorphous strip at 50 and 60 Hz. Specific core loss at 13 or 14 kG [1.3 or 1.4T], specific exciting power at 13 or 14 kG [1.3 or 1.4T], and the flux density, B, at 1 Oe [79.6 A/m] are the recommended parameters for evaluating power grade amorphous materials. 1.1 This test method covers tests for various magnetic properties of flat-cast amorphous magnetic materials at power frequencies (50 and 60 Hz) using sheet-type specimens in a yoke-type test fixture. It provides for testing using either single- or multiple-layer specimens. Note 18212;This test method has been applied only at frequencies of 50 and 60 Hz, but with proper instrumentation and application of the principles of testing and calibration embodied in the test method, it is believed to be adaptable to testing at frequencies ranging from 25 to 400 Hz.1.2 This test method provides a test for specific core loss, specific exciting power and ac peak permeability at moderate and high flux densities, but is restricted to very soft magnetic materials with dc coercivities of 0.07 Oe [5.57 A/m] or less.1.3 The test method also provides procedures for calculating ac peak permeability from measured peak values of total exciting currents at magnetic field strengths up to about 2 Oe [159 A/m].1.4 Explanation of symbols and abbreviated definitions appear in the text of this test method. The official symbols and definitions are listed in Terminology A 340.1.5 This test method shall be used in conjunction with Practice A 34/A 34M.1.6 The values stated in either customary (cgs-emu and inch-pound) or SI units are to be regarded separately as standard. Within this standard, SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with this standard.1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Alternating-Current Magnetic Properties of Amorphous Materials at Power Frequencies Using Wattmeter-Ammeter-Voltmeter Method with Sheet Specimens

SN/T 0812-1999 出口电工仪表.数字多用表检验规程

Electrotechnical instrument for export.Rules for the inspection of digital multi-use meter

DLA SMD-5962-97563 REV A-1998 100-BIT,100多相串行-并行-串行存贮器类似体对数字转换器混合微电路

This drawing documents five product assurance classes, class D (lowest reliability), class E, (exceptions), class G (lowest high reliability), class H (high reliability), and class K, (highest reliability) and a choice of case outlines and lead finishes are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of radiation hardness assurance levels are reflected in the PIN.

MICROCIRCUIT, HYBRID, ANALOG TO DIGITAL CONVERTER, 10-BIT, 100 MSPS

IEEE 1122-1998 高电压脉冲测试中测量用数字记录器

This standard defines the terms specifically related to the digital recorders used for monitoring high-voltage and high-current impulse tests, specifies the necessary performance characteristics for such digital recorders to ensure their compliance with the requirements for highvoltage and high-current impulse tests, and describes the tests and procedures that are necessary to show that these performance characteristics are within the specified limits.

Standard for Digital Recorders for Measurements in High-Voltage Impulse Tests

DLA SMD-5962-95701-1996 15伏特单通道不隔离直流电和直流电转换器线型混合微电路

This drawing forms a part of a one part - one part number documentation system (see 6.6 herein).

MICROCIRCUIT, HYBRID, LINEAR, DC/DC CONVERTER, 15 VOLT, SINGLE CHANNEL, NON-ISOLATED