N70 试验机与无损探伤仪器综合 标准查询与下载

GJB 6757-2009 运载火箭低速风洞试验方法

本标准规定了在低速风洞中进行运载火箭测力及地面风载荷试验的方法。 本标准适用于在低速风洞中进行运载火箭测力及地面风载荷试验。

Test method of launch vehicle in low speed wind tunnel

JJG 909-2009 滚筒式车速表检验台检定规程

本规程适用于汽车或摩托车用滚筒式车速表检验台(以下简称车速台)的首次检定、后续检定和使用中检验。

Verification Regulation of Roller Type Speedometer Tester

DIN EN ISO 3452-5:2009 无损检验 渗透试验 第5部分:温度高于50℃条件下的渗透测试

This part of ISO 3452 specifies the testing requirements particular to applications at higher temperatures (over 50 ℃) and also the method for qualification of suitable testing products. It applies only to materials qualified for the relevant temperature range used in accordance with the manufacturer's instructions.

Non-destructive testing - Penetrant testing - Part 5: Penetrant testing at temperatures higher than 50 °C (ISO 3452-5:2008); English version of DIN EN ISO 3452-5:2009-04

DIN EN ISO 3452-6:2009 无损检验 渗透试验 第6部分:温度低于10℃的渗透测试

This part of ISO 3452 specifies the testing requirements particular to applications at low temperatures (lower than + 10 ~C) as well as the method for qualification of suitable testing products. It applies only to materials qualified for the relevant temperature range used in accordance with the manufacturer's instructions.

Non-destructive testing - Penetrant testing - Part 6: Penetrant testing at temperatures lower than 10 °C (ISO 3452-6:2008); English version of DIN EN ISO 3452-6:2009-04

DIN 54191:2009 无损检验 电子装置的温度记录测试

Non-destructive testing - Thermographic testing of electric installations

BS EN ISO 3452-5:2008 无损检验.渗透测试.温度高于50℃条件下的渗透试验

Non-destructive testing - Penetrant testing - Penetrant testing at temperatures higher than 50 degrees C

BS EN ISO 3452-6:2008 无损检验.渗透测试.温度低于10℃时的渗透测试

Non-destructive testing - Penetrant testing - Penetrant testing at temperatures lower than 10 degrees C

DIN EN ISO 15548-2:2009 无损检验.涡流检验设备.第2部分:探针特性和鉴定

This part of ISO 15548 identifies the functional characteristics of a probe and its interconnecting elements and provides methods for their measurement and verification. The evaluation of these characteristics permits a well-defined description and comparability of eddy current equipment. By careful choice of the characteristics, a consistent and effective eddy current examination system can be designed for a specific application. Where accessories are used, these should be characterised using the principles of this part of ISO 15548. This part of ISO 15548 does not give the extent of verification nor acceptance criteria for the characteristics. These are given in the application documents.

Non-destructive testing - Equipment for eddy current examination - Part 2: Probe characteristics and verification (ISO 15548-2:2008); English version of DIN EN ISO 15548-2:2009-01

DIN EN ISO 15548-1:2009 无损检验.涡流检验设备.第1部分:仪器特性和鉴定

This part of ISO 15548 identifies the functional characteristics of a general-purpose eddy current instrument and provides methods for their measurement and verification. The evaluation of these characteristics permits a well-defined description and comparability of eddy current equipment. By careful choice of the characteristics, a consistent and effective eddy current examination system can be designed for a specific application. Where accessories are used, these are characterised using the principles of this part of ISO 15548. This part of ISO 15548 gives neither the extent of verification nor acceptance criteria for the characteristics. They are given in the application documents.

Non-destructive testing - Equipment for eddy current examination - Part 1: Instrument characteristics and verification (ISO 15548-1:2008); German version EN ISO 15548-1:2008

DIN EN ISO 15548-3:2009 无损检验.涡流检验设备.第3部分:系统特性和鉴定

This part of ISO 15548 identifies the functional characteristics of a general-purpose eddy current system and provides methods for their measurement and verification. The evaluation of these characteristics permits a well-defined description and comparability of an eddy current equipment. By careful choice of the characteristics, a consistent and effective eddy current examination system can be designed for a specific application. Where accessories are used, these are characterised using the principles of this part of ISO 15548. This part of ISO 15548 does not give the extent of verification nor acceptance criteria for the characteristics. These are given in the application documents.

Non-destructive testing - Equipment for eddy current examination - Part 3: System characteristics and verification (ISO 15548-3:2008); English version of DIN EN ISO 15548-3:2009-01

BS EN ISO 15548-3:2008 无损检测.涡流检验设备.设备特性和验证

This part of ISO 15548 identifies the functional characteristics of a general-purpose eddy current system and provides methods for their measurement and verification. The evaluation of these characteristics permits a well-defined description and comparability of an eddy current equipment. By careful choice of the characteristics, a consistent and effective eddy current examination system can be designed for a specific application. Where accessories are used, these are characterised using the principles of this part of ISO 15548. This part of ISO 15548 does not give the extent of verification nor acceptance criteria for the characteristics. These are given in the application documents.

Non-destructive testing - Equipment for eddy current examination - Part 3: System characteristics and verification

BS EN ISO 15548-1:2008 无损检测.涡流检验用设备.器械特性和验证

This part of ISO 15548 identifies the functional characteristics of a general-purpose eddy current instrument and provides methods for their measurement and verification. The evaluation of these characteristics permits a well-defined description and comparability of eddy current equipment. By careful choice of the characteristics, a consistent and effective eddy current examination system can be designed for a specific application. Where accessories are used, these are characterised using the principles of this part of ISO 15548. This part of ISO 15548 gives neither the extent of verification nor acceptance criteria for the characteristics. They are given in the application documents.

Non-destructive testing - Equipment for eddy current examination - Part 1: Instrument characteristics and verification

BS EN ISO 15548-2:2008 无损检测.涡流检验设备.探针特性和验证

This part of ISO 15548 identifies the functional characteristics of a probe and its interconnecting elements and provides methods for their measurement and verification. The evaluation of these characteristics permits a well-defined description and comparability of eddy current equipment. By careful choice of the characteristics, a consistent and effective eddy current examination system can be designed for a specific application. Where accessories are used, these should be characterised using the principles of this part of ISO 15548. This part of ISO 15548 does not give the extent of verification nor acceptance criteria for the characteristics. These are given in the application documents.

Non-destructive testing - Equipment for eddy current examination - Part 2: Probe characteristics and verification

NF A09-170-3*NF EN ISO 15548-3:2008 无损检验.涡流检验设备.第3部分:系统特征和验证

Non-destructive testing - Equipment for eddy current examination - Part 3 : system characteristics and verification.

NF A09-170-2:2008 无损试验.涡流测试设备.第2部分:探测器特性和验证

Non-destructive testing - Equipment for eddy current examination - Part 2 : probe characteristics and verification.

NF A09-170-1:2008 无损检验.涡流检查设备.第1部分:仪器特征和验证

Non-destructive testing - Equipment for eddy current examination - Part 1 : instrument characteristics and verification.

JJF 1210-2008 低速转台校准规范

本规范适用于角速率不大于2000°/s的低速转台（以下简称转台）的校准。

Calibration Specification for Rate Table

KS B ISO 12721:2008 无损检测.热中子射线照相试验.中子束L/D比率的测定

이 표준은 유효 집속비와 20∼1 000 사이의 값을 갖는 열 중성자 투과빔의 유효 L/D

Non-destructive testing－Thermal neutron radiographic testing－Determination of beam L/D ratio

KS B ISO 15708-2:2008 无损检验.辐射法.计算机断层摄影.第2部分:检验的实施规程

이 표준은 컴퓨터 단층촬영(Computed Tomography, 이하 CT) 검사 수행 절

Non-destructive testing－Radiation methods－Computed tomography－Part 2：Examination practices

KS B ISO 12715:2008 超声无损检测.接触式传感器光束轮廓特性的检测程序和基准块

이 표준은 2개의 금속 기준 시험편, 즉 반원 계단(HS:hemi-step)형과 측면공(s

Ultrasonic non-destructive testing－Reference blocks and test procedures for the characterization of contact search unit beam profiles