N72 非金属材料试验机 标准查询与下载

JB/T 9388-2002 界面张力仪.技术条件

　　本标准规定了界面张力仪的技术要求、检验方法、检验规则及标志、包装、运输与贮存。 　　本标准适用于0mN/m～200mN/m手动及电动界面张力仪。

Specifications for the interface tensiometers

ISO 5893:2002 橡胶塑料拉力、压力和弯曲试验机(恒速驱动) 技术规范

This International Standard specifies requirements for tensile-testing systems operating at constant rate of traverse and suitable for testing rubbers, plastics and adhesives, although any one system may only be applicable to a narrower range of materials. It also covers such systems when used for flexural, shear and compression tests.

Rubber and plastics test equipment - Tensile, flexural and compression types (constant rate of traverse) - Specification

JB/T 8763-2001 电液式水泥压力试验机 技术条件

本标准规定了电液式水泥压力试验机的技术要求、检验方法、检验规则、标志与包装等内容。 本标准适用于最大试验力（F|(N)）不大于300kN的电液式水泥压力试验机。

Specifications for the electro-hydraulic compression testing machines for cement

JB/T 9385-1999 刮板细度计 技术条件

　　本标准规定了刮板细度计的结构和规格、技术要求、试验方法、检验规则及标志、包装、运输与贮存。 　　本标准适用于检验色漆、清漆及其他物态类似的产品中分散的固体颗粒细度的刮板细度计。

Specifications for the scraper fineness gauges

JB/T 9386-1999 摆杆阻尼试验仪 技术条件

　　本标准规定了摆杆阻尼试验仪的技术要求、检验方法、检验规则及标志、包装、运输与贮存。 　　本标准适用于按GB/T 1730测定漆膜硬度用的摆杆阻尼试验仪。

Specifications for the pendulum damping testers

ASTM D76-99 纺织材料的拉伸试验机

1.1 This specification covers the operating characteristics of three types of tensile testing machines used for the determination of the force-elongation properties of textile materials. These types of tensile testing machines are: 1.1.1 Constant-rate-of-extension, CRE. 1.1.2 Constant-rate-of-traverse, CRT. 1.1.3 Constant-rate-of-loading (force), CRL. 1.2 Specifications for tensile testing machines to measure other tensile-related properties of textile materials not covered by this standard are given in the ASTM standards using those machines. 1.3 The values stated in SI units are to be regarded as standard; the values in inch-pound units are provided as information only and are not exact equivalents. 1.4 The following safety hazards caveat pertains only to the test methods described in this specification: This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Tensile Testing Machines for Textiles

ASTM D76-99(2005) 纺织材料的拉伸试验机

1.1 This specification covers the operating characteristics of three types of tensile testing machines used for the determination of the force-elongation properties of textile materials. These types of tensile testing machines are:1.1.1 Constant-rate-of-extension, CRE.1.1.2 Constant-rate-of-traverse, CRT.1.1.3 Constant-rate-of-loading (force), CRL.1.2 Specifications for tensile testing machines to measure other tensile-related properties of textile materials not covered by this standard are given in the ASTM standards using those machines.1.3 The values stated in SI units are to be regarded as standard; the values in inch-pound units are provided as information only and are not exact equivalents.1.4 The following safety hazards caveat pertains only to the test methods described in this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Tensile Testing Machines for Textiles

JB/T 8761-1998 塑料悬臂梁冲击试验机

本标准规定了塑料悬臂梁冲击试验机的结构、基本参数、技术要求、检验方法、检验规则、标志与包装等内容。 本标准适用于对硬质塑料、纤维增强复合材料、玻璃钢、陶瓷、石棉等非金属材料进行冲击试验用的塑料悬臂冲击试验机。

Izod impact testing machines for plastics

JB/T 8762-1998 塑料简支梁冲击试验机

本标准规定了塑料简支梁冲击试验机的结构、基本参数、技术要求、检验方法、检验规则、标志与包装等内容。 本标准适用于对硬质塑料、纤维增强复合材料、玻璃钢、陶瓷、石棉等非金属材料进行简支梁冲击试验用的摆锤式冲击试验机。

Charpy impact testing machines for plastics

BS 7825-1:1995 橡胶和塑料试验设备的校准.原则和一般要求规范

Specifies the principles of calibration and general requirements for measurement traceability, the basis for deciding calibration intervals and estimates of uncertainty.

Calibration of rubber and plastics test equipment - Specification for principles and general requirements

JB/T 7797-1995 橡胶、塑料拉力试验机.技术条件

本标准规定了橡胶、塑料拉力试验机的技术要求、试验方法和检验规则等内容。 本标准适用于试验橡胶、塑料或类似材料的试验机。

Rubber, plastic tension testing machine - Technical specifications

WJ 2285-1995 活性炭、浸渍炭试验用测定管检定规程

Verification rules for measuring tubes for activated carbon and impregnated carbon tests

WJ 2284-1995 活性炭、浸渍炭测试用试验筛检定规程

Test sieve test procedure for activated carbon and impregnated carbon

JB/T 7410-1994 塑料球压痕硬度计 技术条件

本标准规定了塑料球压痕硬度计的技术要求，检验方法、检验规则、标志与包装等内容。 本标准适用于按GB 3398《塑料球压痕硬度试验方法》测定塑料和硬橡胶等材料球压痕硬度用的塑料球压痕硬度计。

Specifications for Plastic Ball Indentation Hardness Tester

JB/T 7409-1994 塑料洛氏硬度计.技术条件

本标准规定了塑料洛氏硬度计（E-L-M-R-P-S-V标尽）的技术要求、检验方法、检验规则、标志与包装内容。 本标准适用于按GB 9342《塑料洛氏硬度试验方法》测定塑料洛氏硬度和a硬度用的塑料洛氏硬度计。

Plastic Rockwell apparatus - Technical condition

JIS B 7756:1993 塑料材料用冲击试验机械.仪表法

この規格は，硬質プラスチック及びその複合材料の衝撃試験に用いる計装化衝撃試験機()(以下，試験機という。)の計装化装置の性能について規定する。注()衝撃波形を取り込んで，必要なデータを測定できる装置を備えた衝撃試験機。

Impact testing machines for plastic materials -- Instrumentation

ISO 5893:1993 橡胶和塑料试验设备.抗拉、抗弯和抗压缩型(恒定的横动速率).描述

Rubber and plastics test equipment; tensile, flexural and compression types (constant rate of traverse); description

JB/T 6866-1993 数显陶瓷抗折试验机 技术条件

本标准规定了数量陶瓷抗折试验机的技术要求、试验方法、检验规则、成套性、随机文件、标志、包装和贮存等内容。 本标准适用于按GB 8917《陶瓷砖弯曲强度试验方法》对陶瓷砖瓦及其它脆性材料进行弯曲强底试验用的数量陶瓷砖抗折（弯曲强度）试验机。

Technical conditions of digital display ceramic flexural testing machine

QB/T 1663-1992 电子式纸透油度测定仪

本标准规定了电子式纸透油度测定仪的产品分类、技术要求、试验方法、检验规则和标志、包装、运输、贮存要求。 本标准适用于电子式纸透油度测定仪(以下简称测定仪)的生产验收和质量评定，测定仪使用中的周期技术状态检查亦应参照使用。

Electronic paper oil permeability tester

QB/T 1662-1992 克列姆吸收性测定仪

本标准规定了克列姆吸收性测定仪的产品分类、技术要求、试验方法、检验规则和标志、包装、运输、贮存要求。 本标准适用于克列姆吸收性测定仪(以下简称测定仪)的生产验收和质量评定，测定仪使用中的周期技术状态检查亦应参照使用。

Krem absorbency tester