共找到 354 条与 木结构工程 相关的标准,共 24 页
Timber structures - Vibration performance criteria for timber floors
This document specifies the product and per formance requirements for finger-jointed structural timber made from sawn timber elements. The document does not cover products made using impressed (die- formed) joints or finger-jointed laminations for glued laminated timber, which is covered in ISO 12578.
Timber structures - Finger-jointed timber - Manufacturing and production requirements
1.1 This guide identifies variables to consider when evaluating repetitive-member assembly performance for parallel framing systems. 1.2 This guide defines terms commonly used to describe interaction mechanisms. 1.3 This guide discusses general approaches to quantifying an assembly adjustment including limitations of methods and materials when evaluating repetitive-member assembly performance. 1.4 This guide does not detail the techniques for modeling or testing repetitive-member assembly performance. 1.5 The analysis and discussion presented in this guideline are based on the assumption that a means exists for distributing applied loads among adjacent, parallel supporting members of the system. 1.6 Evaluation of creep effects is beyond the scope of this guide. 1.7 This guide does not purport to suggest or establish appropriate safety levels for assemblies, but cautions users that designers often interpret that safety levels for assemblies and full structures should be higher than safety levels for individual structural members. Note 1: Methods other than traditional safety factor approaches, such as reliability methods, are increasingly used to estimate the probability of failure of structural elements. However, the extension of these methods to assemblies or to complete structures is still evolving. For example, complete structures will likely exhibit less variability than individual structural elements. Additionally, there is a potential for beneficial changes in failure modes (i.e., more ductile failure modes in systems). These considerations are beyond the scope of this guide. 1.8 The values stated in inch-pound units are to be regarded as the standard. The SI equivalents are approximate in many cases. 1.9 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 1.10 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Standard Guide for Evaluating System Effects in Repetitive-Member Wood Assemblies
Timber structures - Calculation and verification of characteristic values; German version EN 14358:2016
Timber structures - Structural insulated panel roof construction - Test methods
Timber structures. Test methods. Determination of the long term behaviour of coated and uncoated dowel-type fasteners
本规范适用于地震区和抗震设防烈度不大于8度地震区的民用建筑用瓷板、陶板、微晶玻璃板、石材蜂窝复合板、高压热固化木纤维板和纤维水泥板等外墙用人造板材幕墙工程。人造板材幕墙的应用高度不宜大于100m。
Technical code for artificial panel curtain wall engineering
Timber structures - Test methods - Withdrawal capacity of timber fasteners; German version EN 1382:2016
Timber structures - Test methods - Pull through resistance of timber fasteners; German version EN 1383:2016
Timber structures - Tests methods - Load bearing stapled joints; German version EN 1381:2016
Timber structures - Strength graded structural timber with rectangular cross section - Part 1: General requirements; German version EN 14081-1:2016
Timber structures - Glued laminated timber - Component performance requirements
Timber structures - Test method - Static load tests for horizontal diaphragms including floors and roofs
Timber structures - Strength graded structural timber with rectangular cross section - Part 1 : general requirements
Timber structures - Test methods - Floor vibration performance
Timber structures. Test methods. Load bearing stapled joints
Timber Structures. Test methods. Withdrawal capacity of timber fasteners
Timber structures. Test methods. Pull through resistance of timber fasteners
Building timber structures. Rules of strength grading of sawn timber
Timber structures - Cross laminated timber - Requirements
Copyright ©2007-2022 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号