P40 给水、排水工程综合 标准查询与下载

DB42/T 349.12-2018 武汉市主要行业取（用）水定额 第12部分：乘用车制造

Water intake (use) quotas for major industries in Wuhan Part 12: Passenger car manufacturing

DB42/T 349.13-2018 武汉市主要行业取（用）水定额 第13部分：玻璃及玻璃制品制造

Water intake (use) quotas for major industries in Wuhan City Part 13: Manufacturing of glass and glass products

CJ/T 521-2018 生活热水水质标准

　　现批准《生活热水水质标准》为城镇建设行业产品标准，编号为CJ/T521-2018，自2018年11月1日起实施。 　　本标准在住房城乡建设部门户网站（www.mohurd.gov.cn）公开，并由住房城乡建设部标准定额研究所组织中国标准出版社出版发行。  　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　中华人民共和国住房和城乡建设部 　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　  2018年4月3日

Domestic hot water quality standard

DB3403/T 02-2018 蚌埠市城市行业用水定额

Bengbu City Industry Water Quota

DB45/T 679-2017 城镇生活用水定额

Urban domestic water quota

DB45/T 678-2017 工业行业主要产品用水定额

Water consumption quotas for main products in industrial sectors

DB37/T 5105-2017 山东省城市生活用水量标准

本标准适用于确定城市生活用水量指标。

Standards for Urban Domestic Water Consumption in Shandong Province

DB11/T 1494-2017 城镇二次供水技术规程

Technical specification for secondary water supply in cities and towns

DB11/T 1492-2017 城镇排水管道结构等级评定

Structural Grade Evaluation of Urban Drainage Pipelines

DB46/T 449-2017 海南省用水定额

本标准适用于海南省行政区域内的用水计划管理、节约用水管理、取水许可审批、建设项目水资源论证等相关工作。水利规划设计、国民经济有关行业发展规划等可参照使用。

Hainan Province Water Quota

CJ/T 270-2017 聚乙烯塑钢缠绕排水管及连接件

本标准规定了用钢带与聚乙烯（中密度或高密度）通过挤出方式成型的塑钢复合带材，经缠绕焊接制成的塑钢缠绕排水管的术语和定义、符号、代号，材料，产品结构、分类和连接方式，要求，试验方法，检验规则，标志、运输、贮存。 该管材适用于长期输送介质温度在45℃以下的无压埋地城镇排水、工业排水以及农田排水等工程。

Steel reinforced spirally wound Polyethylene(PE) drainage pipe

CJ/T 283-2017 偏心半球阀

本标准规定了偏心半球阀的术语和定义、结构型式及型号、材料、要求、试验方法、检验规则、标志、包装和贮存。 本标准适用于公称尺寸DN 40~DN 2000，最大允许工作压力不大于6.3 MPa，介质为水、浆液或物理化学性质类似于水的其他液体的偏心半球阀。

Eccentric semi-ball valves

ISO 24516-3:2017 供水和污水系统资产管理指南.第3部分:污水收集管网

This document specifies guidelines for technical aspects, tools and good practices for the management of assets of wastewater networks to maintain value from existing assets. This document does not apply to the management of assets of treatment plants, which are also physically part of the wastewater system and can influence the management of network assets. NOTE 1 The management of the following individual assets will be covered by ISO 24516-4: wastewater pumping stations, retention and detention in the network, wastewater treatment plants and sludge treatment facilities. This document includes examples of good practice approaches on the strategic, tactical and operational levels. This document is applicable to all types and sizes of organizations and/or utilities operating wastewater networks, and all different roles/functions for the management of assets within a utility (e.g. asset owner/responsible body, asset manager/operator, service provider/operator). NOTE 2 Depending on the size and structure of an organization, the utility can decide to what extent it applies the guidance in this document, but in any case, the philosophy of this document remains applicable to small and medium utilities.

Guidelines for the management of assets of water supply and wastewater systems - Part 3: Wastewater collection networks

DB42/T 349.11-2017 武汉市主要行业取（用）水定额 第11部分：商务写字楼

Water intake (use) quotas for major industries in Wuhan City Part 11: Commercial office buildings

DB42/T 349.10-2017 武汉市主要行业取（用）水定额 第10部分：电子电器制造

Water intake (use) quotas for major industries in Wuhan City Part 10: Manufacturing of electronic appliances

DB42/T 349.9-2017 武汉市主要行业取（用）水定额 第9部分：食品制造

Water intake (use) quotas for major industries in Wuhan Part 9: Food manufacturing

BS PAS 13:2017 采用安全屏障抗冲击试验方法测定工作场所环境内交通管理使用安全屏障的实施规程

Code of practice for safety barriers used in traffic management within workplace environments with test methods for safety barrier impact resilience

ISO 24523:2017 饮用水系统和废水系统相关服务活动. 水设施基准指南

Service activities relating to drinking water supply systems and wastewater systems - Guidelines for benchmarking of water utilities

ASTM F2764/F2764M-17 无压卫生下水道应用6至60英寸[150至1500 mm]聚丙烯(PP)波纹状双壁和三壁管及配件的标准规格

1.1 This specification covers requirements and test methods for corrugated double and triple wall polypropylene pipe and fittings. The nominal inside diameters covered are 6 to 60 in. [150 to 1500 mm]. 1.2 The requirements of this specification are intended to provide pipe and fittings for underground use for non-pressure sanitary sewer systems. Pipe and fittings produced in accordance with this specification shall be installed in compliance with Practice D2321. 1.3 This specification covers pipe and fittings with an annular corrugated wall and an essentially smooth interior wall (that is, double wall) (Fig. 1) and pipe and fittings with an annular corrugated wall and an essentially smooth interior and exterior wall (that is, triple wall) (Fig. 2). FIG. 1 Typical Corrugated Double Wall Pipe FIG. 2 Typical Corrugated Triple Wall Pipe 1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.5 The following precautionary statement applies only to Section 7 of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for 6 to 60 in. [150 to 1500 mm] Polypropylene (PP) Corrugated Double and Triple Wall Pipe and Fittings for Non-Pressure Sanitary Sewer Applications

ASTM F2764/F2764M-17e1 无压卫生下水道应用6至60英寸[150至1500 mm]聚丙烯(PP)波纹状双壁和三壁管及配件的标准规格

1.1 This specification covers requirements and test methods for corrugated double and triple wall polypropylene pipe and fittings. The nominal inside diameters covered are 6 to 60 in. [150 to 1500 mm]. 1.2 The requirements of this specification are intended to provide pipe and fittings for underground use for non-pressure sanitary sewer systems. Pipe and fittings produced in accordance with this specification shall be installed in compliance with Practice D2321. 1.3 This specification covers pipe and fittings with an annular corrugated wall and an essentially smooth interior wall (that is, double wall) (Fig. 1) and pipe and fittings with an annular corrugated wall and an essentially smooth interior and exterior wall (that is, triple wall) (Fig. 2). FIG. 1 Typical Corrugated Double Wall Pipe FIG. 2 Typical Corrugated Triple Wall Pipe 1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.5 The following precautionary statement applies only to Section 7 of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Standard Specification for 6 to 60 in. [150 to 1500 mm] Polypropylene (PP) Corrugated Double and Triple Wall Pipe and Fittings for Non-Pressure Sanitary Sewer Applications