P42 建筑给水、排水工程 标准查询与下载

NF P36-411-1:2000 地上外部用塑料雨水管道系统.第1部分:非塑化聚氯乙烯(PVC-U)管道系统.第1部分:管,配件和系统规范

Plastics rainwater piping systems for above ground external use - Unplasticized poly(vinyl chloride) (PVC-U) - Part 1 : specifications for pipes, fittings and the system.

NF P40-201/A2:2000 DTU 60.1.建筑工程.住宅卫生管道.技术规范

DTU 60.1 - Building works - Sanitary plumbing in residential buildings - Technical specifications.

CECS 118-2000 冷却塔验收测试规程

本规程为循环水冷却塔热力性能验收测试、噪声测试和飘滴损失水量测试提供统一的程序，各项参数的测量方法及测试数据的处理方法。 本规程适用于湿式冷却塔安装现场的验收测试，不适用于干式冷却塔、干湿式冷却塔及喷射式冷却塔的验收测试。非验收性质的冷却塔测试可参照本规程执行。

Specification for acceptance test of water-cooling tower

ANSI/NSF 40-2000 住宅废水处理系统

Revises the alarms and warranty requirements and modifies the foreword. This is a resolution ballot for a BSR 108 sent in June or July but was returned to the Joint Committee for resolution.

Residential Wastewater Treatment Systems

CECS 105-2000 建筑给水铝塑复合管管道工程技术规程

本规程适用于新建、改建和扩建的工业与民用建筑中冷、热水供应管道系统的设计、施工及验收；系统的工作压力不大于0.6MPa，工作温度不大于75℃。

Technical specification for polyethylene-aluminum composite pipeline engineering of building water supply

DIN EN 12889:2000 排水管和污水管非埋设施工和试验

The document is applicable to the trenchless construction and testing of new drains and sewers in the ground normally operating as gravity pipelines using prefabricated pipes and their joints.

Trenchless construction and testing of drains and sewers; German version EN 12889:2000

NF P16-330-4:2000 建筑物集水沟.第4部分:入口盖

Gullies for buildings - Part 4 : access covers.

ASTM F2021-00 塑料虹吸式屋面排水系统的设计和安装标准规范

1.1 This specification covers requirements for plastic syphonic roof drain systems for industrial, commercial, public, and residential buildings. Requirements for materials, pipe, and fittings are included.1.2 The interchangeability of pipe and fittings made by different manufacturers is not addressed in this specification. Transition fittings for joining pipe and fittings of different manufacturers is provided for in the referenced pipe and fitting specification.1.3 In referee decisions, the SI units shall be used for metric-sized pipe and inch-pound units for pipe sized in the IPS system (ANSI B36.10). In all cases, the values given in parentheses are for information only.1.4 The following safety hazards caveat pertains only to the test methods, Section 7 , of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Specification for Design and Installation of Plastic Syphonic Roof Drainage Systems

ANSI/NSF 41-1999 非液体渗透处理系统

Spreads the data plate requirements and revisions to sections 12-14 to make fecal coliform analyses consistent with methods used by EPA .

Non-Liquid Saturated Treatment Systems

BS EN 12109:1999 建筑物内真空排水道系统

This European Standard specifies system requirements (performance) and the principal requirements for design and installation, with related verification and test methods, for vacuum drainage systems inside buildings transporting domestic wastewater from dwellings and commercial properties, but excluding stormwater and rainwater. If requirements for products used within the system are needed, annex D (informative) provides guidance to performance requirements, design, verification and quality assurance. The gravity system which feeds the wastewater to the vacuum drainage system is not covered by this European Standard.

Vacuum drainage systems inside buildings

CJ/T 39-1999 平面格栅

Plane bar screen

CECS 103-1999 循环冷却水系统不停车化学清洗和热态预膜工艺技术规程

本规程适用于石油、化工、冶金（净或清循环系统）、电力、轻工、纺织等工业企业及大中型中央空调装置循环冷却水系统的不停车化学清洗和热态预膜；也适用于新建或大修后循环冷却水系统开车清洗和热态预膜。本规程中有关热态预膜的内容还适用于循环冷却水系统发生低pH事故后，采用热态预膜进行保护性处理的场合。

Technology-Technical Code for On line chemical cleaning and prefilming(under the load of heat)of recirculating cooling water system

BS EN 1253-2:1999 建筑物的集水沟.试验方法

Gullies for buildings - Test methods

BOCA NBC COMM V2 CH 29-1999 水管系统

Plumbing Systems

Plumbing Systems

BS EN 1852-1:1998 无压地下排水管和下水道用塑料管道系统.聚丙烯(PP).管道,管配件及系统规范

This Part of EN 1852 specifies the requirements for pipes, fittings and the system of polypropylene (PP) piping systems in the field of: - non-pressure underground drainage and sewerage outside the building structure (application area code 'U'); and - non-pressure underground drainage and sewerage for both buried in ground within the building structure (application area code 'D') and outside the building structure. This is reflected in the marking of products by 'U' and 'UD'. It also specifies the test parameters for the test methods referred to in this standard. This standard covers a range of nominal sizes, a range of pipe series/stiffness classes and gives recommendations concerning colours. NOTE 1. It is the responsibility of the purchaser or specifier to make the appropriate selection from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes. In conjunction with Part 2 and Part 3 of EN 1852 it is applicable to PP pipes and fittings, their joints and to joints with components of other plastics and non-plastics materials intended to be used for buried piping systems for non-pressure underground drainage and sewerage. This standard is applicable to PP pipes with or without an integral socket. NOTE 2. The fittings can be manufactured by injection moulding or be fabricated from pipes and/or mouldings. NOTE 3. Requirements and limiting values for application area code 'D' are given in table 3, table 6 and table 12. NOTE 4. Pipes, fittings and other components conforming to any of the plastics product standards listed in annex B may be used with pipes and fittings conforming to this standard when they conform to the requirements for joint dimensions given in clause 6 and to the requirements of table 12.

Plastics piping systems for non-pressure underground drainage and sewerage - Polypropylene (PP) - Specifications for pipes, fittings and the system

BOCA IOTFDC-1998 CHAPTER 35-1998 卫生排水

A person shall not willfully fail or refuse to comply with any lawful order or direction of the fire prevention code officiai or to interfere with the compliance attempts of another individual.

Sanitary Drainage

ASCE 95-1998 城市浅地排水表

The intent of this Manual is to present information to help determine the need for, make investigations, plan solutions, design, construct, operate and maintain urban subsurface drainage systems. For more guidance on urban subsurface drainage, see ANSVASCE 12-92, Standard Guidelines for Design of Urban Subsurface Drainage, ASCE 13-93, Standard Guidelines for Installation of Urban Subsurfi Drainage, and ASCE 14-93, Standard Guidelines for Operation and Maintenance of Urban Subsurface Drainage. These Guidelines are available from the ASCE Publications Department, 1801 Alexander Bell Drive, Reston, VA 20191-4400. Copyright

Urban Subsurface Drainage

BOCA IOTFDC-1998 CHAPTER 31-1998 总水管要求

This eleventh edition presents the code as originally issued, with changes approved through 1989, and with certain editorial changes made to maintain the sequence of the code, to standardize the format of all 1990 BOCA National Codes, and to update the

General Plumbing Requirements

BOCA IOTFDC-1998 CHAPTER 32-1998 水龙头和夹具装置,水管装置

The following is a listing of the standards referenced in this code, the effective date of the standard, the promulgating agency of the standard and the section(s) of this code that refer to the standard.

Plumbing Fixtures, Faucets and Fixture Fittings

BOCA IOTFDC-1998 CHAPTER 34-1998 水的供应和分配

The fire prevention code official shall recommend to the chief administrative official of the municipality the location or relocation of new or existing fire hydrants and the placement or replacement of inadequate water mains located upon public prope

Water Supply and Distribution