P46 供热、采暖工程 标准查询与下载

BS EN 1264-1:2011 水基表面嵌入式加热和冷却系统.定义和符号

This European Standard is applicable to water based surface embedded heating and cooling systems in residential, office and other buildings, the use of which corresponds to or is similar to that of residential buildings. This European Standard applies to heating and cooling systems embedded into the enclosure surfaces of the room to be heated or to be cooled. It also applies as appropriate to the use of other heating media instead of water.

Water based surface embedded heating and cooling systems. Definitions and symbols

CJJ/T 55-2011 供热术语标准

本标准适用于供热及有关领域。

Standard for terminology of heating

DIN EN 15316-4-8:2011 建筑物供暖系统.系统能量要求和系统功效的计算方法.第4-8部分:空间供热发电系统,热风供热和高空辐射供热系统;德文版本EN 15316-4-8-2011

This European Standard is part of a series of standards on the method for calculation of system energy requirements and system efficiencies. The scope of this specific part is to standardise the: -required inputs; -calculation method; -resulting outputs for space heating generation by: a) air heating systems, including control, and b) overhead radiant heating systems for non-domestic use, including control. This European Standard does not apply to air heating systems that utilise water as a heat transfer medium.

Heating systems in buildings - Method for calculation of system energy requirements and system efficiencies - Part 4-8: Space heating generation systems, air heating and overhead radiant heating systems; German version EN 15316-4-8:2011

BS EN 15316-4-8:2011 建筑物中的供暖系统.系统能量要求和系统功效的计算方法.空间发热系统,热风供热和辐射供热系统

This European Standard is part of a series of standards on the method for calculation of system energy requirements and system efficiencies. The scope of this specific part is to standardise the: ? required inputs; ? calculation method; ? resulting outputs for space heating generation by: a) air heating systems, including control, and b) overhead radiant heating systems for non-domestic use , including control. This European Standard does not apply to air heating systems that utilise water as a heat transfer medium.

Heating systems in buildings. Method for calculation of system energy requirements and system efficiencies. Space heating generation systems, air heating and overhead radiant heating systems

DB35/T 1137-2011 小型汽水两用锅炉房安全管理规范

本标准规定了小型汽水两用锅炉房的术语和定义、基本要求、锅炉房管理等内容。本标准适用于额定蒸发量不超过0.5t/h、额定蒸汽压力不超过.04MPa的小型汽水两用锅炉房

Code for safety management of small steam-water dual-purpose boiler room

JG/T 293-2010 压铸铝合金散热器

Die-cast aluminum alloy radiator

NF P52-612/CN:2010 建筑物供热系统.设计热载荷的计算方法.NF EN 12831标准国家增加件.第6至9条计算的缺省值.

Heating systems in buildings - Method for calculation of the design heat load - National addition to NF EN 12831 - Default values for the calculations in clauses 6 to 9.

DIN EN 13941:2010 集中供暖用预绝缘粘结管系统的设计和安装.德文及英文版本EN 13941-2009 + AC-2009

Design and installation of preinsulated bonded pipe systems for district heating; German and English version EN 13941:2009+A1:2010

DB13/T 1287-2010 汽轮机循环水余热供热技术规程

本标准规定了循环水供热原理和注意事项、热电厂循环水供热机组的运行技术参数及配备设备性能参数、循环水供热投入步骤、循环水供热解列步骤、循环水供热机组事故处理、调峰站设备的操作步骤。本标准适用于地方小型热电厂循环水供热机组（型号为C12-50/10的抽凝式机组）。

Technical specification for steam turbine circulating water waste heat heating

DB13/T 1308-2010 发热电缆地面供暖技术规程

本标准规定了发热电缆地面供暖的范围、规范性引用文件、术语和定义、设计、材料、施工、检查调试与验收。本标准适用于将发热电缆铺设在新建建筑地板中，以发热电缆为热源加热室内地面的供暖系统。发热电缆地面供暖工程的设计、施工及验收，除应执行本标准外，尚应符合国家现行的有关强制性标准的规定。

Technical specification for heating cable floor heating

NF P52-617-4-1:2010 建筑物供暖系统.系统能量要求和系统功效的计算方法.第4-1部分:空间发热系统,燃烧系统(锅炉).

Heating systems in buildings - Method for calculation of system energy requirements and system efficiencies - Part 4-1 : space heating generation systems, combustion systems (boilers).

CJJ 34-2010 城镇供热管网设计规范

为节约能源，保护环境，促进生产，改善人民生活，发展我国城镇集中供热事业，提高集中供热工程设计水平，做到技术先进、经济合理、安全适用，制定本规范。 本规范适用于供热热水介质设计压力小于或等于2.5MPa，设计温度小于或等于200℃；供热蒸汽介质设计压力小于或等于1.6MPa，设计温度小于或等于350℃的下列城镇供热管网的设计： 1 以热电厂或锅炉房为热源，自热源至建筑物热力入口的供热管网； 2 供热管网新建、扩建或改建的管线、中继泵站和热力站等工艺系统。 城镇供热管理设计应符合城镇规划要求，并宜注意美观。 在地震、湿陷性黄土、膨胀土等地区进行城镇供热管网设计时，除应符合本规范外，尚应符合现行国家标准《室外给水排水和燃气热力工程抗震设计规范》GB 50032、《湿陷性黄土地区建筑规范》GB 50025、《膨胀土地区建筑技术规范》GBJ 112的规定。 城镇供热管网的设计除应符合本规范外，尚应符合国家现行相关标准的规定。

Design code for city heating network

EN 13941:2009+A1:2010 区域供暖预绝缘、结合管道系统的设计与安装

This European Standard specifies rules for design, calculation and installation for preinsulated bonded pipe systems for buried hot water distribution and transmission networks (cf. Figure 2) with pipe assemblies in accordance with EN 253, for continuous operation with hot water at various temperatures up to 120 ° C and occasionally with peak temperatures up to 140 ° C and maximum internal pressure 25 bar (overpressure). Application rule: For larger pipe dimensions and pressures below 25 bar wall thickness bigger than specified in EN 253 can be required for straight pipes, bends and tees. The principles of the standard can be applied to preinsulated pipe systems with pressures higher than 25 bar, provided that special attention is paid to the effects of pressure. Adjacent pipes belonging to the network (e. g. pipes in ducts, valve chambers, road crossings above ground etc.) can be designed and installed according to this standard. The standard assumes use of treated water, which by softening, demineralisation, deaeration, adding of chemicals, or otherwise has been treated to prevent internal corrosion and deposits in the pipes. This standard is not applicable for such units as: a) pumps, b) exchangers, c) boiler installations, tank installations, d) consumer installations. However, the full functional ability and durability of such units should be ensured in consideration of the impacts from the district heating system and other impacts occurring from the conditions under which they have been installed. Guidelines for product quality inspection and in situ tests of joints are given in Annex A of EN 448:2009, Annex D of EN 253:2009, Annex A of EN 488:2009 and Annex B of EN 489:2009. Guidelines for welding of polyethylene casing are given in Annex B of EN 448:2009. The estimation of expected life with continuous operation at various temperatures is outlined in Annex B of EN 253:2009.

Design and installation of preinsulated bonded pipe systems for district heating

CJJ 138-2010 城镇地热供热工程技术规程

本规程适用于以地热井提取地热流体为热源的城镇供热工程的规划、设计、施工、验收及运行管理。

Technical specification for geothermal space heating engineering

BS EN 15632-3:2010 区域加热管.预绝缘柔性管系统.带塑料给水管道的非粘接系统.要求和试验方法

This European Standard provides requirements and test methods for flexible, pre-insulated, direct buried district heating pipes with plastic service pipes and no bonding between the layers of the pipes.

District heating pipes - Pre-insulated flexible pipe systems - Non bonded system with plastic service pipes; requirements and test methods

BS EN 15632-2:2010 区域加热管.预绝缘柔性管系统.粘结塑料供水管.要求和试验方法

This European Standard provides requirements and test methods for flexible, pre-insulated, directly buried heating pipes with plastics service pipes and bonding between the layers of the pipes. This European Standard is valid for maximum operating temperatures of 95 °C and maximum operating pressures up to 10 bar for a design lifetime of at least 30 years.

District heating pipes - Pre-insulated flexible pipe systems - Bonded plastic service pipes - Requirements and test methods

DB13/T 1165-2009 低温热水地面供暖系统售后服务规范

本标准规定了低阻热水地面供暖系统(以下简称地面供暖系统〉售后服务的术语与定义、基本原则和基本要求。本标准适用于公共建筑、民用建筑和家庭装修的地面供暖系统的售后服务。

Specifications for after-sales service of low temperature hot water floor heating system

NF P52-617-4-7:2009 建筑物加热系统.系统能量要求和系统效率的计算方法.第4-6部分:发热系统、光电系统

Heating systems in buildings - Method for calculation of system energy requirements and system efficiencies - Part 4-7 : space heating generation systems, biomass combustion systems.

BS EN 1264-4:2009 水基表面嵌入加热和冷却系统.安装

Water based surface embedded heating and cooling systems - Installation

BS EN 1264-3:2009 内部水基表面加热和冷却系统.第3部分:尺寸标注

This European Standard applies to heating and cooling systems embedded into the enclosure surfaces of the room to be heated or to be cooled. This document deals with the use in practical engineering of the results coming from part 2 and 5 and is applicable to floor-, ceiling- and wall heating systems, as well floor-, ceiling- and wall cooling systems. For heating systems, physiological limitations are taken into account when specifying the surface temperatures. In the case of floor heating systems the limitations are realised by a design based on the characteristic curves and limit curves determined in accordance with part 2 of this Standard. For cooling systems, only a limitation with respect to the dew point is taken into account. In predominating practice, this means that physiological limitations are included as well.

Water based surface embedded heating and cooling systems - Part 3: Dimensioning