Q15 墙体材料 标准查询与下载

DIN V 105-100:2005 粘土砌块.第100部分:具有特殊性能的粘土砌块

Clay masonry units - Part 100: Clay masonry units with specific properties

BS EN 1052-5:2005 圬工的试验方法.粘结扭转法测定粘结强度

This document specifies a method for determining the bond strength of horizontal bed joints in masonry using a bond wrench. Guidance is given on the preparation of the specimens, the conditioning required before testing, the testing equipment, machine, the method of test, the method of calculation and the contents of the test report.

Methods of test for masonry - Determination of bond strength by the bond wrench method

NF P31-302:2005 粘土屋面瓦和配件.产品定义和规范

Clay roofing tiles and fittings - Product definitions and specifications.

DIN EN 13748-1:2005 水磨石砖.第1部分:内部用水磨石砖

This European Standard specifies materials, properties and methods of testing for unreinforced cement-bound terrazzo tiles which are factory made and sold ready to be placed. The tiles are intended for internal use.#,,#

Terrazzo tiles - Part 1: Terrazzo tiles for internal use; German version EN 13748-1:2004 + A1:2005 + AC:2005

DIN V 20000-401:2005 结构物中建筑产品的应用.第401部分:符合DIN EN 771-1-2005的粘土砌块的应用规则

This prestandard gives provisions for the application of clay masonry units according to DIN EN 771-1:2003-08

Application of building products in structures - Part 401: Rules for the application of clay masonry units according to DIN EN 771-1:2005-05

DIN V 20000-402:2005 结构物中建筑产品的应用.第402部分:符合DIN EN 771-2-2005的硅酸钙砌块的应用规则

This prestandard gives provisions for the application of clay units according to DIN EN 771-2:2003-08

Application of building products in structures - Part 402: Rules for the application of calcium silicate masonry units according to DIN EN 771-2:2005-05

KS F 2263-2005 建筑用板材弯曲测试方法

이 규격은 건축용 보드류(1)의 휨 시험 방법에 대하여 규정한다.주(1) 건축용 보드

Method of bending test for boards of buildings

DIN EN 13748-2:2005 水磨面砖.第2部分:外部用水磨面砖

Terrazzo tiles - Part 2: Terrazzo tiles for external use; German version EN 13748-2:2004

DIN V 52252-3:2005 磨光盖面粘土砖和熔渣砖的耐霜冻性测定的试验方法.第3部分:测试壁的单面冷动

The freeze-thaw test method described in this standard serves to asses the frost resistance of fair faced clay-bricks and clinker-bricks used in the outer walls of buildings.

Test method for the determination of the frost resistance of fair faced clay-bricks and clincer-bricks - Part 3: One side freezing of test walls

ASTM C1072-05a 砌块抗弯粘结强度的测定的标准试验方法

1.1 This test method covers the determination of flexural bond strength of nonreinforced masonry by physical testing of each joint of masonry prisms.1.2This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Measurement of Masonry Flexural Bond Strength

ASTM C687-05 测定松填建筑绝热材料热阻的标准实施规程

1.1 This practice presents a laboratory guide to determine the thermal resistance of loose-fill building insulations at mean temperatures between 20 and 55C (4 to 131F).1.2 This practice applies to a wide variety of loose-fill thermal insulation products including fibrous glass, rock/slag wool, or cellulosic fiber materials; granular types including vermiculite and perlite; pelletized products; and any other insulation material installed pneumatically or poured in place. It does not apply to products that change their character after installation either by chemical reaction or the application of binders or adhesives, nor does it consider the effects of structures, containments, facings, or air films.1.3 Since this practice is designed for reproducible product comparison, it measures the thermal resistance of an insulation material which has been preconditioned to a relatively dry state. Consideration of changes of thermal performance of a hygroscopic insulation by sorption of water is beyond the scope of this practice.1.4 The sample preparation techniques outlined in this practice do not cover the characterization of loose-fill materials intended for enclosed applications. For those applications, a separate sample preparation technique that simulates the installed condition will be required. However, even for those applications, some other aspects of this practice are applicable.1.5 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Practice for Determination of Thermal Resistance of Loose-Fill Building Insulation

ASTM C1072-05b 砌块抗弯粘结强度的测定的标准试验方法

1.1 This test method covers the determination of flexural bond strength of nonreinforced masonry by physical testing of each joint of masonry prisms.1.2This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Measurement of Masonry Flexural Bond Strength

ASTM C1072-05 砌块抗弯粘结强度的测定的标准试验方法

1.1 This test method covers the determination of flexural bond strength of nonreinforced masonry by physical testing of each joint of masonry prisms. 1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Method for Measurement of Masonry Flexural Bond Strength

ASTM C62-05 建筑砖(粘土或页岩制实心砌块)的标准规范

1.1 This specification covers brick intended for both structural and nonstructural masonry where external appearance is not a requirement. The brick are prismatic units available in a variety of sizes, shapes, textures, and colors. The specification does not cover brick intended for use as facing units or where surface appearance is a requirement, (see Specification C 216). This specification does not cover brick intended for use as paving brick (see Specification C 902).1.2 The property requirements of this standard apply at the time of purchase. The use of results from testing of brick extracted from masonry structures for determining conformance or nonconformance to the property requirements (Section 3) of this standard is beyond the scope of this standard.1.3 Brick are manufactured from clay, shale, or similar naturally occurring earthy substances and subjected to a heat treatment at elevated temperatures (firing). The heat treatment must develop sufficient fired bond between the particulate constituents to provide the strength and durability requirements of this specification. (See firing, fired bond, and incipient fusion in Terminology C 43.)1.4 Brick are shaped during manufacture by molding, pressing, or extrusion, and the shaping method is a way to describe the brick (see Terminology C 43).1.5 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.1.6 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.

Standard Specification for Building Brick (Solid Masonry Units Made From Clay or Shale)

ASTM C652-05a 空心砖(粘土或页岩制空心砌块)的标准规范

1.1 This specification covers hollow building brick and hollow facing brick made from clay, shale, fire clay, or mixtures thereof, and fired to incipient fusion. Four types of hollow brick in each of two grades and two classes are covered. In this specification the term hollow brick shall be understood to mean hollow clay masonry units whose net cross-sectional area (solid area) in any plane parallel to the surface, containing the cores, cells, or deep frogs, is less than 75 % of its gross cross-sectional area measured in the same plane (see ). This specification does not cover brick intended for use as paving brick (see Specification C 902).1.2 The property requirements of this standard apply at the time of purchase. The use of results from testing of brick extracted from masonry structures for determining conformance or nonconformance to the property requirements (Section ) of this standard is beyond the scope of this standard.1.3 Brick covered by this specification are manufactured from clay, shale, or similar naturally occurring substances and subjected to a heat treatment at elevated temperatures (firing). The heat treatment shall develop sufficient fired bond between the particulate constituents to provide the strength and durability requirements of this specification. (See "firing" and "firing bond" in Terminology C 43.)1.4 Hollow brick differ from unglazed structural clay tile (Specifications C 34 and C 212) and solid brick (Specifications C 62 and C 216). Hollow brick require greater shell and web thicknesses and higher minimum compressive strength than structural clay tile, but permit greater void area and lesser distance from exposed edge to core hole than solid brick. Therefore, environmental and structural performance may be different in elements constructed of hollow brick from those constructed of structural clay tile or solid brick.1.5 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.1.6 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.

Standard Specification for Hollow Brick (Hollow Masonry Units Made From Clay or Shale)

ASTM C652-05 空心砖(粘土或页岩制空心砌块)的标准规范

1.1 This specification covers hollow building brick and hollow facing brick made from clay, shale, fire clay, or mixtures thereof, and fired to incipient fusion. Four types of hollow brick in each of two grades and two classes are covered. In this specification the term hollow brick shall be understood to mean hollow clay masonry units whose net cross-sectional area (solid area) in any plane parallel to the surface, containing the cores, cells, or deep frogs, is less than 75 % of its gross cross-sectional area measured in the same plane (see 3.3). This specification does not cover brick intended for use as paving brick (see Specification C 902).1.2 The property requirements of this standard apply at the time of purchase. The use of results from testing of brick extracted from masonry structures for determining conformance or nonconformance to the property requirements (Section 5) of this standard is beyond the scope of this standard.1.3 Brick covered by this specification are manufactured from clay, shale, or similar naturally occurring substances and subjected to a heat treatment at elevated temperatures (firing). The heat treatment shall develop sufficient fired bond between the particulate constituents to provide the strength and durability requirements of this specification. (See "firing" and "firing bond" in Terminology C 43.)1.4 Hollow brick differ from unglazed structural clay tile (Specifications C 34 and C 212) and solid brick (Specifications C 62 and C 216). Hollow brick require greater shell and web thicknesses and higher minimum compressive strength than structural clay tile, but permit greater void area and lesser distance from exposed edge to core hole than solid brick. Therefore, environmental and structural performance may be different in elements constructed of hollow brick from those constructed of structural clay tile or solid brick.1.5 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.1.6 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.

Standard Specification for Hollow Brick (Hollow Masonry Units Made From Clay or Shale)

ASTM C744-05 预制混凝土及硅酸钙砌块的标准规范

1.1 This specification covers prefaced concrete masonry units with the exposed-to-view-in-place surfaces covered at the point of manufacture with resin, resin and inert filler, or cement and inert filler to produce a smooth resinous tile facing. 1.2 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.

Standard Specification for Prefaced Concrete and Calcium Silicate Masonry Units

ASTM C67-05 砖及结构粘土瓦取样和试验的标准试验方法

1.1 These test methods cover procedures for the sampling and testing of brick and structural clay tile. Although not necessarily applicable to all types of units, tests include modulus of rupture, compressive strength, absorption, saturation coefficient, effect of freezing and thawing, efflorescence, initial rate of absorption and determination of weight, size, warpage, length change, and void area. (Additional methods of test pertinent to ceramic glazed facing tile are included in Specification C 126.) 1.2 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.Note 18212;The testing laboratory performing this test method should be evaluated in accordance with Practice C 1093.1.3 Unless otherwise indicated, the values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Test Methods for Sampling and Testing Brick and Structural Clay Tile

ASTM C1587-05a 抗压强度试验用现场可拆卸人造砌块和组件的制备的标准实施规程

1.1 The purpose of this practice is to standardize the preparation of manufactured masonry units and assemblies extracted from the field for compressive strength testing in a laboratory environment.1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and to determine the applicability of regulatory limitations prior to use.

Standard Practice for Preparation of Field Removed Manufactured Masonry Units and Assemblies for Compressive Strength Testing

ASTM C1587-05 抗压强度试验用现场可拆卸人造砌块和组件的制备的标准实施规程

1.1 The purpose of this practice is to standardize the preparation of manufactured masonry units and assemblies extracted from the field for compressive strength testing in a laboratory environment.1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and to determine the applicability of regulatory limitations prior to use.

Standard Practice for Preparation of Field Removed Manufactured Masonry Units and Assemblies for Compressive Strength Testing